TJA1021T/10/CM - 20 kbps LIN Bus Transceiver | NXP
MPN: TJA1021T/10/CM ✗ اختتامِ زندگیTJA1021T/10/CM جائزہ
A LIN transceiver, also called a LIN physical-layer interface, is the semiconductor bridge between a microcontroller-based LIN protocol controller and the physical LIN wiring harness. It belongs to the interface IC hierarchy, connecting automotive and industrial network controllers to a low-cost, single-wire communications bus. Unlike a logic-level serial transceiver, the TJA1021 includes the physical bus driver, receiver, voltage regulator, waveform shaping, and fault-recovery functions required by LIN nodes.
The TJA1021T/10/CM operates from 5.5 V to 27 V, supports bus rates from 1 kBd to 20 kBd, and has a bus output current of 4 mA. Its 10 uA low-power specification supports energy-conscious node implementations. The optimized slew rate and wave shaping minimize electromagnetic emissions, while enhanced ESD protection of ±6 kV improves robustness in automotive environments exposed to ESD events on the bus wiring.
The integrated voltage regulator supplies the external transceiver circuitry, reducing the number of supporting components. Communication features include local and bus wake-up, TXD timeout protection, bus-fault protection, and thermal shutdown. According to the NXP manufacturer documentation, the TJA1021 is pin-compatible with the TJA1020 and MC33662(B), allowing those devices to be considered when an existing board uses the same SOIC-8 footprint.
Typical uses include LIN master nodes in vehicle body controllers, door and seat modules, climate-control interfaces, ambient-light sensors, switch panels, and industrial supervisory controllers. The 20 kBd ceiling supports the highest baud rates specified by the cited LIN and SAE J2602 protocols, while local and bus wake-up provide practical options for low-current systems.
PCB layout should preserve the transceiver layout specified in the manufacturer datasheet, keep the LIN connection away from sensitive analog and high-speed digital traces, and provide a low-impedance return path to the ground plane. Verify the exact pin orientation, exposed connections, external resistor and capacitor requirements, and transceiver-state behavior against the current NXP datasheet before releasing a new layout.
This page organizes the manufacturer specifications, protocol coverage, lifecycle information, drop-in cross-references, application guidance, and design considerations needed to evaluate the TJA1021T/10/CM for an existing LIN node design.
کے لیے ڈراپ اِن متبادل TJA1021T/10/CM — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TJA1021T/10/CM (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Product Type, Package, ESD Protection, Package Type.
TJA1020T/N1
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TJA1021T/20/C
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TJA1021BT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
MC33662JEF
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TJA1021T/10/CM تفصیلات
| Product Type | LIN bus transceiver |
| Maximum LIN Baud Rate | 20 kBd |
| Supported LIN Baud Rate Range | 1 kBd to 20 kBd |
| Supply Voltage Range | 5.5 V to 27 V |
| Quiescent or Low-Power Current | 10 uA |
| Bus Output Current | 4 mA |
| ESD Protection | ±6 kV |
| پیکیج | 8-pin SOIC, 3.90 mm width |
| ماؤنٹنگ ٹائپ | Surface mount |
| Supported LIN Versions | LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A |
| Automotive Protocol Support | SAE J2602 |
| International Standard Support | ISO 17987-4:2016 |
| Protection Features | Bus fault protection and thermal shutdown |
| Wake-Up Features | Local wake-up and bus wake-up |
| Controller Interface Protection | TXD timeout protection |
| Voltage Regulator | Integrated |
| Pin Compatibility | Compatible with TJA1020 and MC33662(B) |
| RoHS اسٹیٹس | Compliant |
TJA1021T/10/CM 8-pin soic, 3.90 mm width پن کنفیگریشن گائیڈ
TJA1021T/10/CM (8-pin soic, 3.90 mm width پیکیج) کے لیے پن کنفیگریشن۔ پن نمبرنگ، فنکشنز اور کنکشن ڈایاگرامز مینوفیکچرر کے ڈیٹا شیٹ میں بیان کیے گئے ہیں۔ درست فٹ پرنٹ اور سولڈرنگ رہنما ہدایات کے لیے اسی سے رجوع کریں۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TJA1021T/10/CM.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
TJA1021T/10/CM کے لیے موزوں ہے 6 ایپلیکیشنs: Automotive LIN Master Node, Vehicle Door and Seat Module, Climate-Control Interface, Ambient and Accessory Sensor Node, Industrial LIN Controller Interface, Switch Panel and HMI Subnet.
Automotive LIN Master Node
The TJA1021T/10/CM fits a LIN master node that converts TXD commands from a protocol controller into standardized bus waveforms and returns bus state through RXD. Its 1 kBd to 20 kBd operating range covers the protocol families cited by the manufacturer, while optimized slew rate and wave shaping reduce electromagnetic emissions. The integrated voltage regulator and 4 mA bus output capability simplify the physical-layer section of a body, lighting, or climate-control controller. Designers should still verify the master timing, pull-up arrangement, and external component values against the NXP application circuit before layout release.
تجویز کردہ
Vehicle Door and Seat Module
A door or seat module can use the TJA1021T/10/CM to communicate switch position, motor commands, and sensor status over a LIN subnet. The 5.5 V to 27 V operating range suits a node connected to an automotive supply environment, while local wake-up and bus wake-up support systems that must remain asleep until the user or remote node requests activity. Its ±6 kV ESD protection is useful on wiring that may be exposed to electrostatic discharge. Confirm the node's sleep-current budget, dominant-state behavior, and temperature qualification against the final vehicle electrical specification.
تجویز کردہ
Climate-Control Interface
The TJA1021T/10/CM is appropriate for climate-control modules that exchange button, position, and sensor information over a low-cost single-wire network. Supporting LIN 2.0 through LIN 2.2A, SAE J2602, and ISO 17987-4:2016 gives the physical layer broad compatibility with established automotive network specifications. The device's integrated regulator reduces support circuitry, while its 20 kBd maximum rate provides margin within the specified LIN range. Layout should separate the LIN route from sensitive sensor lines and follow the manufacturer's grounding and bus-termination guidance.
تجویز کردہ
Ambient and Accessory Sensor Node
An ambient-light, door-position, or accessory sensor node can use the TJA1021T/10/CM as its LIN physical-layer interface. The 10 uA low-power figure helps when the node spends extended periods in sleep, and local or bus wake-up provides two practical activation paths. At the maximum documented LIN rate of 20 kBd, the interface supports standard automotive network timing without a separate physical-layer transceiver. The system designer should account for the controller's sleep current, sensor standby demand, and the total node leakage when evaluating the advertised low-power characteristic.
تجویز کردہ
Industrial LIN Controller Interface
The TJA1021T/10/CM can bridge an embedded controller to a LIN physical bus in an industrial subsystem using inexpensive wiring. Its 5.5 V to 27 V supply range, 20 kBd maximum communication rate, and bus-fault protection support robust point-to-point and multi-node arrangements. The device's standardized LIN behavior is valuable when interoperating with third-party controllers, while wake-up functions reduce the need for continuously active node electronics. For industrial deployment, verify immunity, operating temperature, grounding, cable length, and protection requirements for the installation environment.
تجویز کردہ
Switch Panel and HMI Subnet
A switch panel, rotary controller, or human-machine interface can use the TJA1021T/10/CM to connect user commands to a LIN master. The standardized physical layer supports communication from 1 kBd to 20 kBd and includes local wake-up for activation at the panel. Integrated voltage regulation can simplify the transceiver supply arrangement, while TXD timeout protection helps the system respond safely when the host controller stops issuing valid transmit commands. The interface should be placed away from display switching and high-current actuator traces to minimize coupling into the LIN waveform.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TJA1021T/10/CM — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TJA1020 | TJA1021T/20 | TJA1021BT | MC33662(B) |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Documented Pin Compatibility | Pin-compatible with TJA1020 and MC33662(B) | Pin-compatible with TJA1021 | Same TJA1021 family | Pin-to-pin and hardware/software compatible with TJA1021T/20 | Pin-compatible with TJA1021 |
اہم امتیازی خصوصیات
- Supports the full documented 20 kBd LIN operating range (بمقابلہTJA1020)
- Provides both local and bus wake-up functions (بمقابلہMC33662(B))
- Uses an ESD-protected LIN physical layer for vehicle wiring (بمقابلہTJA1021T/20)
ڈیزائن نوٹس
Place the TJA1021T/10/CM and its required external components according to the NXP application circuit. Keep the LIN connection away from switching-regulator nodes, display flex cables, and other high-edge-rate traces. Use a continuous ground reference beneath the device and avoid routing the bus through areas with switching-current loops. The optimized slew-rate circuitry reduces emissions, but layout symmetry and controlled return paths remain necessary for reliable waveform quality.
Provide a supply that remains within the specified 5.5 V to 27 V operating range across load transients, wiring losses, and automotive supply disturbances. Decouple the device close to its supply and ground pins, and use the regulator output only for the loads permitted by the manufacturer application circuit. Do not infer absolute-maximum or transient tolerances from the operating range; use the NXP manufacturer datasheet for those limits.
A same-footprint device is not automatically a functional substitute. Compare TXD polarity, dominant and recessive levels, RXD output behavior, regulator output, wake-up logic, timeout response, ESD rating, and LIN timing before replacing TJA1021T/10/CM. The TJA1020, TJA1021BT, and MC33662(B) each have documented compatibility attributes, but production qualification should include the complete node power states and bus timing tests.
Use the manufacturer's recommended LIN bus routing and termination arrangement to control waveform rise time and minimize radiated emissions. Keep external regulator and bus components close to their associated device pins, and avoid long stubs from the LIN trace. If the enclosure, cable, or neighboring harness produces difficult EMC results, verify that the complete reference design—not only the transceiver—is being compared, because cable impedance and node configuration strongly influence emissions.
تعمیل کی معلومات
RoHS compliance is identified for the exact TJA1021T/10/CM,118 order code. The listing identifies the device as an automotive LIN transceiver with AEC-Q100 status. REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified.