TJA1021T/10/CM - 20 kbps LIN Bus Transceiver | NXP
料号: TJA1021T/10/CM ✗ 停产TJA1021T/10/CM 概述
A LIN transceiver, also called a LIN physical-layer interface, is the semiconductor bridge between a microcontroller-based LIN protocol controller and the physical LIN wiring harness. It belongs to the interface IC hierarchy, connecting automotive and industrial network controllers to a low-cost, single-wire communications bus. Unlike a logic-level serial transceiver, the TJA1021 includes the physical bus driver, receiver, voltage regulator, waveform shaping, and fault-recovery functions required by LIN nodes.
The TJA1021T/10/CM operates from 5.5 V to 27 V, supports bus rates from 1 kBd to 20 kBd, and has a bus output current of 4 mA. Its 10 uA low-power specification supports energy-conscious node implementations. The optimized slew rate and wave shaping minimize electromagnetic emissions, while enhanced ESD protection of ±6 kV improves robustness in automotive environments exposed to ESD events on the bus wiring.
The integrated voltage regulator supplies the external transceiver circuitry, reducing the number of supporting components. Communication features include local and bus wake-up, TXD timeout protection, bus-fault protection, and thermal shutdown. According to the NXP manufacturer documentation, the TJA1021 is pin-compatible with the TJA1020 and MC33662(B), allowing those devices to be considered when an existing board uses the same SOIC-8 footprint.
Typical uses include LIN master nodes in vehicle body controllers, door and seat modules, climate-control interfaces, ambient-light sensors, switch panels, and industrial supervisory controllers. The 20 kBd ceiling supports the highest baud rates specified by the cited LIN and SAE J2602 protocols, while local and bus wake-up provide practical options for low-current systems.
PCB layout should preserve the transceiver layout specified in the manufacturer datasheet, keep the LIN connection away from sensitive analog and high-speed digital traces, and provide a low-impedance return path to the ground plane. Verify the exact pin orientation, exposed connections, external resistor and capacitor requirements, and transceiver-state behavior against the current NXP datasheet before releasing a new layout.
This page organizes the manufacturer specifications, protocol coverage, lifecycle information, drop-in cross-references, application guidance, and design considerations needed to evaluate the TJA1021T/10/CM for an existing LIN node design.
直接替换替代料: TJA1021T/10/CM ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。
本系列中的变体
可与以下型号直接替换的同系列型号: TJA1021T/10/CM (相同外形与封装尺寸) ——差异在于 Product Type, Package, ESD Protection, Package Type.
TJA1020T/N1
✅ 直接替换联系询价
查看数据手册 →TJA1021T/20/C
✅ 直接替换 ⚠️ 规格未核验联系询价
查看数据手册 →TJA1021BT
✅ 直接替换📋 参考替代料(不在目录中)
MC33662JEF
✅ 直接替换联系询价
查看数据手册 →TJA1021T/10/CM 规格参数
| Product Type | LIN bus transceiver |
| Maximum LIN Baud Rate | 20 kBd |
| Supported LIN Baud Rate Range | 1 kBd to 20 kBd |
| Supply Voltage Range | 5.5 V to 27 V |
| Quiescent or Low-Power Current | 10 uA |
| Bus Output Current | 4 mA |
| ESD Protection | ±6 kV |
| 封装 | 8-pin SOIC, 3.90 mm width |
| 安装类型 | Surface mount |
| Supported LIN Versions | LIN 2.0, LIN 2.1, LIN 2.2 and LIN 2.2A |
| Automotive Protocol Support | SAE J2602 |
| International Standard Support | ISO 17987-4:2016 |
| Protection Features | Bus fault protection and thermal shutdown |
| Wake-Up Features | Local wake-up and bus wake-up |
| Controller Interface Protection | TXD timeout protection |
| Voltage Regulator | Integrated |
| Pin Compatibility | Compatible with TJA1020 and MC33662(B) |
| RoHS 状态 | Compliant |
TJA1021T/10/CM 8-pin soic, 3.90 mm width 引脚配置指南
TJA1021T/10/CM(8-pin soic, 3.90 mm width 封装)的引脚配置。 引脚编号、功能和连接图在制造商数据手册中定义。请参阅该手册以了解确切的封装尺寸和焊接指南。
暂无详细引脚数据: TJA1021T/10/CM.
请参阅 数据手册 以查看完整引脚配置。
典型应用
TJA1021T/10/CM 适用于 6 应用s: Automotive LIN Master Node, Vehicle Door and Seat Module, Climate-Control Interface, Ambient and Accessory Sensor Node, Industrial LIN Controller Interface, Switch Panel and HMI Subnet.
Automotive LIN Master Node
The TJA1021T/10/CM fits a LIN master node that converts TXD commands from a protocol controller into standardized bus waveforms and returns bus state through RXD. Its 1 kBd to 20 kBd operating range covers the protocol families cited by the manufacturer, while optimized slew rate and wave shaping reduce electromagnetic emissions. The integrated voltage regulator and 4 mA bus output capability simplify the physical-layer section of a body, lighting, or climate-control controller. Designers should still verify the master timing, pull-up arrangement, and external component values against the NXP application circuit before layout release.
推荐
Vehicle Door and Seat Module
A door or seat module can use the TJA1021T/10/CM to communicate switch position, motor commands, and sensor status over a LIN subnet. The 5.5 V to 27 V operating range suits a node connected to an automotive supply environment, while local wake-up and bus wake-up support systems that must remain asleep until the user or remote node requests activity. Its ±6 kV ESD protection is useful on wiring that may be exposed to electrostatic discharge. Confirm the node's sleep-current budget, dominant-state behavior, and temperature qualification against the final vehicle electrical specification.
推荐
Climate-Control Interface
The TJA1021T/10/CM is appropriate for climate-control modules that exchange button, position, and sensor information over a low-cost single-wire network. Supporting LIN 2.0 through LIN 2.2A, SAE J2602, and ISO 17987-4:2016 gives the physical layer broad compatibility with established automotive network specifications. The device's integrated regulator reduces support circuitry, while its 20 kBd maximum rate provides margin within the specified LIN range. Layout should separate the LIN route from sensitive sensor lines and follow the manufacturer's grounding and bus-termination guidance.
推荐
Ambient and Accessory Sensor Node
An ambient-light, door-position, or accessory sensor node can use the TJA1021T/10/CM as its LIN physical-layer interface. The 10 uA low-power figure helps when the node spends extended periods in sleep, and local or bus wake-up provides two practical activation paths. At the maximum documented LIN rate of 20 kBd, the interface supports standard automotive network timing without a separate physical-layer transceiver. The system designer should account for the controller's sleep current, sensor standby demand, and the total node leakage when evaluating the advertised low-power characteristic.
推荐
Industrial LIN Controller Interface
The TJA1021T/10/CM can bridge an embedded controller to a LIN physical bus in an industrial subsystem using inexpensive wiring. Its 5.5 V to 27 V supply range, 20 kBd maximum communication rate, and bus-fault protection support robust point-to-point and multi-node arrangements. The device's standardized LIN behavior is valuable when interoperating with third-party controllers, while wake-up functions reduce the need for continuously active node electronics. For industrial deployment, verify immunity, operating temperature, grounding, cable length, and protection requirements for the installation environment.
推荐
Switch Panel and HMI Subnet
A switch panel, rotary controller, or human-machine interface can use the TJA1021T/10/CM to connect user commands to a LIN master. The standardized physical layer supports communication from 1 kBd to 20 kBd and includes local wake-up for activation at the panel. Integrated voltage regulation can simplify the transceiver supply arrangement, while TXD timeout protection helps the system respond safely when the host controller stops issuing valid transmit commands. The interface should be placed away from display switching and high-current actuator traces to minimize coupling into the LIN waveform.
推荐
推荐产品汇总
工程参考数据: TJA1021T/10/CM ——对比、设计指导和合规信息。
选型指南
与替代料对比
| 参数 | 本产品 | TJA1020 | TJA1021T/20 | TJA1021BT | MC33662(B) |
|---|---|---|---|---|---|
| Brand | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors | NXP Semiconductors |
| Package | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC | 8-pin SOIC |
| Documented Pin Compatibility | Pin-compatible with TJA1020 and MC33662(B) | Pin-compatible with TJA1021 | Same TJA1021 family | Pin-to-pin and hardware/software compatible with TJA1021T/20 | Pin-compatible with TJA1021 |
关键差异点
- Supports the full documented 20 kBd LIN operating range (对比 TJA1020)
- Provides both local and bus wake-up functions (对比 MC33662(B))
- Uses an ESD-protected LIN physical layer for vehicle wiring (对比 TJA1021T/20)
设计说明
Place the TJA1021T/10/CM and its required external components according to the NXP application circuit. Keep the LIN connection away from switching-regulator nodes, display flex cables, and other high-edge-rate traces. Use a continuous ground reference beneath the device and avoid routing the bus through areas with switching-current loops. The optimized slew-rate circuitry reduces emissions, but layout symmetry and controlled return paths remain necessary for reliable waveform quality.
Provide a supply that remains within the specified 5.5 V to 27 V operating range across load transients, wiring losses, and automotive supply disturbances. Decouple the device close to its supply and ground pins, and use the regulator output only for the loads permitted by the manufacturer application circuit. Do not infer absolute-maximum or transient tolerances from the operating range; use the NXP manufacturer datasheet for those limits.
A same-footprint device is not automatically a functional substitute. Compare TXD polarity, dominant and recessive levels, RXD output behavior, regulator output, wake-up logic, timeout response, ESD rating, and LIN timing before replacing TJA1021T/10/CM. The TJA1020, TJA1021BT, and MC33662(B) each have documented compatibility attributes, but production qualification should include the complete node power states and bus timing tests.
Use the manufacturer's recommended LIN bus routing and termination arrangement to control waveform rise time and minimize radiated emissions. Keep external regulator and bus components close to their associated device pins, and avoid long stubs from the LIN trace. If the enclosure, cable, or neighboring harness produces difficult EMC results, verify that the complete reference design—not only the transceiver—is being compared, because cable impedance and node configuration strongly influence emissions.
合规信息
RoHS compliance is identified for the exact TJA1021T/10/CM,118 order code. The listing identifies the device as an automotive LIN transceiver with AEC-Q100 status. REACH, lead-free, halogen-free, and conflict-minerals declarations were not identified.