TPS22997QRYZRQ1 - 10A, 5.5V Load Switch | Texas Instruments
MPN: TPS22997QRYZRQ1 ✓ فعالTPS22997QRYZRQ1 جائزہ
A load switch is a power management IC that gates a power rail on and off using an integrated MOSFET controlled by a logic-level enable pin. In the power management hierarchy, load switches sit between the power source (a DC-DC converter or LDO) and the load, providing controlled power-up sequencing, inrush limiting, rail isolation, and fault protection that raw converters do not offer.
Key features include adjustable slew-rate control to minimize inrush current during turn-on, an adjustable quick output discharge (QOD) pin that actively pulls the output low when disabled, and a power-good output for rail monitoring and sequencing. The ON pin can interface directly with low-voltage GPIO signals. Thermal shutdown and low quiescent power consumption round out the feature set.
Technically, the 4 mΩ RON translates to only 40 mV of drop at 10A and just 0.4W of conduction loss, eliminating the need for a heatsink. The configurable rise time allows designers to trade startup time against inrush current to protect upstream regulators and downstream capacitors.
Typical applications include automotive ADAS processor and FPGA power sequencing, infotainment rail gating, sensor module power control, and battery-connected load management in 5V and sub-5V systems. The Q1 qualification supports all AEC-Q100 automotive ambient temperature grades.
Design tip: use the CT pin capacitor to set slew rate so that inrush into large downstream bulk capacitance stays within the upstream supply current limit, and verify bias voltage is present before asserting ON.
کے لیے ڈراپ اِن متبادل TPS22997QRYZRQ1 — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TPS22997QRYZRQ1 (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف On-Resistance (RON), Package, Power Good Output, Slew Rate Control.
TPS22997RYZR
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →ET3164
✅ ڈراپ-اِن ⚠️ تفصیلات غیر تصدیق شدہ📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TPS22997QRYZRQ1 زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Channel Count | 1 |
| Switch Type | N-Channel MOSFET (high-side) |
| Input Voltage Range (VIN) | 0.1 V to 5.5 V |
| Bias Voltage Range (VBIAS) | 1.5 V to 5.5 V |
| Maximum Continuous Current | 10 A |
| On-Resistance (RON) | 4 mOhm (typical) |
| Slew Rate Control | Adjustable via CT pin |
| Quick Output Discharge (QOD) | Adjustable |
| پاور گڈ آؤٹ پٹ | Yes |
| Enable Input (ON) | Yes, low-voltage GPIO compatible |
| تھرمل شٹ ڈاؤن | Yes |
| پیکیج | 10-WQFN-HR (RYZ), 1.5 mm x 2 mm |
| ماؤنٹنگ ٹائپ | Surface Mount |
| Qualification | AEC-Q100 (automotive) |
| RoHS اسٹیٹس | Compliant |
TPS22997QRYZRQ1 پن کنفیگریشن
| پن 1 | VBIAS — Bias supply, 1.5V to 5.5V, powers control circuit |
| پن 2 | GND — Ground |
| پن 3 | ON — Enable input, GPIO compatible |
| پن 4 | CT — Slew rate control capacitor pin |
| پن 5 | QOD — Quick output discharge control pin |
| پن 6 | PGOOD — Power good output signal |
| پن 7 | VIN — Input voltage, 0.1V to 5.5V |
| پن 8 | VIN — Input voltage sense |
| پن 9 | VOUT — Switched output voltage |
| پن 10 | VOUT — Switched output voltage |
عام استعمالات
TPS22997QRYZRQ1 کے لیے موزوں ہے 6 ایپلیکیشنs: ADAS Processor Power Sequencing, Infotainment Display and Audio Rail Gating, FPGA and MCU Core Rail Switching, Automotive Camera and Sensor Module Power, Body Electronics and Gateway Rail Control, E-Compressor and Motor Drive Auxiliary Rails.
ADAS Processor Power Sequencing
The TPS22997QRYZRQ1 gates the core and I/O rails of ADAS SoCs such as TDA4 processors, where its 10A capacity and 4 mΩ RON handle multi-amp core supplies with minimal drop (40 mV at 10A). The power-good output lets a sequencer or MCU confirm rail validity before releasing the next rail, while adjustable slew rate prevents inrush from collapsing upstream 5V rails during turn-on. Placed between the point-of-load converter and the processor, it adds no switching noise and only 0.4W conduction loss at full load. AEC-Q100 qualification makes it compliant for production automotive ADAS platforms.
تجویز کردہ
Infotainment Display and Audio Rail Gating
Automotive infotainment head units use the TPS22997QRYZRQ1 to switch display panels and audio amplifier rails, enabling standby power savings. With a 0.1V minimum input and low-voltage GPIO-compatible ON pin, it can be driven directly from an SoC to isolate the 5V display rail. The adjustable quick output discharge actively pulls the display rail low when disabled, preventing ghosting or floating-panel conditions. Its 4 mΩ RON keeps dissipation negligible even for multi-amp amplifier supply rails, and thermal shutdown adds a layer of protection if the display connector shorts.
تجویز کردہ
FPGA and MCU Core Rail Switching
FPGAs and MCUs often require controlled power-down to guarantee deterministic reset. The TPS22997QRYZRQ1 provides controlled turn-off of core rails with active QOD discharge, ensuring the device resets cleanly across power cycles. At currents up to 10A, its 4 mΩ switch adds only milliohm-level IR drop, preserving the tight core voltage margin of modern FPGAs. The CT pin slew-rate control lets designers soften turn-on into large decoupling networks without external FETs or driver circuitry. This saves board area versus discrete MOSFET solutions in dense compute modules.
تجویز کردہ
Automotive Camera and Sensor Module Power
Surround-view and radar sensor modules are powered through long harnesses where inrush must be limited. The TPS22997QRYZRQ1 soft-starts the sensor rail via its CT-configured rise time, limiting inrush into camera module bulk capacitance and protecting the upstream supply from droop below reset thresholds. Its power-good flag reports rail status to the domain controller. AEC-Q100 qualification covers the harsh ambient range of automotive exterior modules, and the tiny 1.5 mm x 2 mm WQFN-HR package fits inside compact camera housings with strict board-area limits.
تجویز کردہ
Body Electronics and Gateway Rail Control
Body control modules and automotive Ethernet gateways use the TPS22997QRYZRQ1 to switch peripheral rails for transceivers and I/O expanders, enabling sleep-mode power reduction. Low power consumption when enabled and clean isolation when disabled reduce quiescent draw below module sleep budgets. The ON pin accepts low-voltage GPIO directly from a TMS320F280015x-class MCU without level shifting when bias is 3.3V. Thermal shutdown protects against connector faults, and the 10A rating covers high-current peripheral rails with ample margin.
تجویز کردہ
E-Compressor and Motor Drive Auxiliary Rails
Motor-drive systems built around gate drivers such as the DRV8353S use the TPS22997QRYZRQ1 to gate isolated auxiliary supply rails for sensors and communication circuits. During fault conditions, the load switch isolates the auxiliary domain quickly, and the QOD discharge guarantees a known state before restart. The 0.1V-5.5V input range accommodates rectified or low-voltage auxiliary rails, and 4 mΩ RON limits heating in thermally constrained drive enclosures. Functional isolation of measurement chains (for example, TMCS1101 current sensors) becomes manageable with one small-SMD switch.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TPS22997QRYZRQ1 — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TPS22997RYZR | ET3164 |
|---|---|---|---|
| Package | 10-WQFN-HR (RYZ) 1.5x2 mm | 10-WQFN-HR (RYZ) - same | 10-WQFN-HR (RYZ) - claimed same |
| Brand | Texas Instruments | Texas Instruments | ETEK (Merrillchip) |
| Max Continuous Current | 10 A | 10 A | 10 A (claimed) |
| Power Good Output | Yes | Yes | Yes (claimed) |
اہم امتیازی خصوصیات
- Automotive AEC-Q100 qualification (بمقابلہTPS22997RYZR)
- Extremely low 4 mΩ on-resistance at 10A (بمقابلہET3164)
- Adjustable slew rate plus adjustable QOD (بمقابلہTPS22997RYZR)
ڈیزائن نوٹس
Size the CT capacitor so the output rise time limits inrush current to a value the upstream regulator can source. Inrush approximates I = (CLOAD x VOUT) / tRISE. For a 1000 uF load charged to 5V in 2 ms, inrush is about 2.5A. Verify the bias rail is established before asserting ON, since the control circuitry is powered from VBIAS, not VIN.
At 10A and 4 mΩ RON, conduction loss is roughly 0.4W (I2R). The 1.5 mm x 2 mm WQFN-HR package relies heavily on the PCB thermal pad; use a solid via array from the exposed pad to at least one internal ground plane. Transient overloads are handled by thermal shutdown, but do not rely on it for repeated faults - it degrades long-term reliability.
Route VIN and VOUT with wide, short copper pours rated for 10A - use at least 2 oz copper or parallel planes for the power path. Place the CT and QOD resistors/capacitors close to their pins to keep control nodes quiet. Keep the PGOOD pull-up on a clean rail, and do not float ON; drive it from a defined logic level to prevent unintended turn-on during startup.
تعمیل کی معلومات
AEC-Q100 qualified automotive Q1 part. RoHS compliance per TI product page; REACH and halogen-free status not stated in retrieved data.
