TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics
MPN: TS9222ID ✓ فعالTS9222ID جائزہ
An operational amplifier is an active analog component that uses high open-loop gain to amplify voltage differences between its differential inputs. Within the analog signal-chain hierarchy, an op amp sits between passive sensor conditioning and higher-level conversion or control functions. Rail-to-rail input and output operation allows the TS9222ID to accept signals near the positive or negative supply rail, while its output can also swing close to those rails.
Key characteristics include a maximum input offset voltage of 500 uV, 80 mA output current per channel, and low input bias current. The 4 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the 1.3 V/us slew rate gives adequate performance for precision feedback networks, instrumentation, and low-to-moderate-frequency signal conditioning. The dual configuration provides two amplifiers in one package, reducing component count on analog boards.
The TS9222ID is built for precision and stability rather than maximum bandwidth. Its 500 uV maximum input offset voltage limits the output error created by input imbalance in a unity-gain configuration. Rail-to-rail inputs help preserve signal integrity in sensor interfaces where the operating point may sit near a supply rail. The stated 80 mA per-channel output capability also allows the amplifier to drive heavier loads than a purely high-impedance signal-processing stage.
Typical applications include current sensing, bridge and instrumentation amplifiers, sensor conditioning, audio preamplification, industrial measurement systems, and automotive electronic modules. The -40C to +125C temperature range supports extended industrial environments, provided that the board-level power supply, bypass capacitors, and stability network follow the manufacturer's recommended implementation.
For reliable operation, place the input and feedback components close to their corresponding pins, bypass each supply rail locally, and verify capacitive-load stability with an isolation resistor when driving cables, ADC inputs, or other long capacitive loads. Use the manufacturer pin-description table when assigning PCB tracks and confirm that the selected amplifier configuration remains stable across the intended gain, load, and supply range.
This page combines package, precision, temperature-range, and interface guidance with same-family drop-in options and a parameter-by-parameter comparison. It is intended to help engineers shorten selection work while preserving the electrical and layout constraints that determine analog performance.
کے لیے ڈراپ اِن متبادل TS9222ID — یکساں پیکیج، پن سے پن مطابقت پذیر۔ مختلف پیکیج والے پرزے جن کے لیے PCB دوبارہ کام درکار ہو، شامل نہیں ہیں۔
اس سیریز میں مختلف ورژن
اسی سیریز کے ماڈلز جو ڈراپ اِن مطابقت رکھتے ہیں TS9222ID (یکساں فارم فیکٹر اور فٹ پرنٹ) — میں مختلف Amplifier Type, Operating Temperature Range, RoHS Status.
TS9222IDT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TS9222IPT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TS9222IYPT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TS9222IYDT
✅ ڈراپ-اِن📋 حوالہ جاتی متبادل (کیٹلاگ میں نہیں)
TS922ID
✅ ڈراپ-اِنقیمت کے لیے رابطہ کریں
ڈیٹا شیٹ دیکھیں →TS9222ID زیادہ سے زیادہ ریٹنگز اور برقی خصوصیات
| Amplifier Type | General Purpose |
| Number of Circuits | 2 circuits |
| Number of Amplifiers | 2 amplifiers |
| Supply Voltage Range | 2.7 V to 12 V |
| Gain Bandwidth Product | 4 MHz |
| Slew Rate | 1.3 V/us |
| Input Offset Voltage | 500 uV maximum |
| Output Current Per Channel | 80 mA |
| Input Bias Current | 15 nA |
| Input Common-Mode Rejection Ratio | 65 dB |
| Input Offset Current | 0.055 uA |
| Input Type | Rail-to-Rail |
| آؤٹ پٹ کی قسم | Rail-to-Rail |
| Capacitive Load Drive | 500 pF |
| آپریٹنگ درجہ حرارت رینج | -40C to +125C |
| پیکیج | 8-SOIC, 0.154 inch width, 3.90 mm length |
| Packaging | Tube |
| ماؤنٹنگ ٹائپ | Surface mount |
| RoHS اسٹیٹس | unknown |
TS9222ID 8-soic, 0.154 inch width, 3.90 mm length پن کنفیگریشن گائیڈ
TS9222ID (8-soic, 0.154 inch width, 3.90 mm length پیکیج) کے لیے پن کنفیگریشن۔ اس اینالاگ کمپوننٹ میں اِن پٹ، آؤٹ پٹ اور پاور سپلائی پنز شامل ہیں۔ آفسیٹ نل، کمپنسیشن اور اِن ایبل پن کنفیگریشنز کے لیے مینوفیکچرر کے ڈیٹا شیٹ سے رجوع کریں۔ سگنل کنڈیشننگ اور ایمپلیفائر سرکٹس کے لیے مثالی۔
کے لیے تفصیلی پن آؤٹ ڈیٹا دستیاب نہیں TS9222ID.
رجوع کریں ڈیٹا شیٹ مکمل پن کنفیگریشن کے لیے۔
عام استعمالات
TS9222ID کے لیے موزوں ہے 6 ایپلیکیشنs: Precision Current Sensing, Bridge Sensor Instrumentation, Industrial Sensor Signal Conditioning, Automotive Control Module Interfaces, Low-Noise Audio Preamplification, Battery and Portable System Buffering.
Precision Current Sensing
The TS9222ID fits low-side or isolated current-sense amplifiers where input error must remain small. Its 500 uV maximum input offset voltage limits the output error referenced to the shunt voltage, while 15 nA input bias current reduces disturbance in high-impedance sensing networks. The dual configuration can amplify the shunt signal and provide a second channel for an intermediate buffer or reference amplifier. The 4 MHz gain-bandwidth product supports common current-mode gains from 1 to 100, although gain-bandwidth interaction must be checked when operating close to the upper limit.
تجویز کردہ
Bridge Sensor Instrumentation
The TS9222ID is well matched to resistive bridge sensing because its dual amplifiers can form the two halves of an instrumentation stage. Rail-to-rail input operation accommodates sensor excitation and signal levels that approach the supply rails, while the 1.3 V/us slew rate supports accurate settling of moderate-bandwidth measurements. Use closely matched feedback resistors to preserve common-mode rejection, and keep input traces short and symmetric. The 500 uV maximum offset specification helps control error in gains greater than one, where input offset is multiplied by the noise gain.
تجویز کردہ
Industrial Sensor Signal Conditioning
The TS9222ID is appropriate for conditioning outputs from pressure, temperature, and position sensors in industrial equipment. Its -40C to +125C operating range covers extended industrial environments, and the rail-to-rail input stage reduces the need to bias signals away from the supply rails. The 4 MHz gain-bandwidth product is sufficient for many slow industrial control loops, while the 80 mA per-channel output current provides headroom for moderate loading. Place the amplifier near the sensor connector when cable capacitance is significant, and add local supply bypassing at the IC pins.
تجویز کردہ
Automotive Control Module Interfaces
The TS9222ID can serve as a general analog interface amplifier inside automotive control modules because it combines rail-to-rail operation with a -40C to +125C temperature specification. It is suitable for conditioning low-voltage sensor inputs, producing buffered control signals, and amplifying diagnostics signals at moderate frequency. The 500 uV maximum input offset voltage supports accurate sensing, while 15 nA input bias current is useful with high-impedance dividers. Confirm device qualification, transient protection, and supply requirements against the vehicle program before production release.
تجویز کردہ
Low-Noise Audio Preamplification
The TS9222ID can amplify low-level audio or instrumentation signals when the design requires rail-to-rail input and output operation. The 15 nA input bias current reduces loading on high-impedance sources, and the 4 MHz gain-bandwidth product provides ample bandwidth for typical audio-band feedback networks. The 1.3 V/us slew rate avoids severe distortion on small, low-frequency signals. Place gain-setting and feedback resistors close to the device, maintain short ground returns, and avoid sharing high-current output paths with the input reference.
تجویز کردہ
Battery and Portable System Buffering
The TS9222ID is suitable for buffering sensors and divider outputs in compact battery-powered systems. Operation from 2.7 V supports 3 V supplies, and rail-to-rail input and output stages improve usable signal range in low-voltage designs. The dual package provides two buffers while limiting board area, and 15 nA input bias current is valuable when the source impedance is high. Power consumption should be evaluated in the final gain and load configuration, and the output should not be used to source power for loads beyond the amplifier's normal drive requirement.
تجویز کردہ
تجویز کردہ پروڈکٹس کا خلاصہ
کے لیے انجینئرنگ ریفرنس ڈیٹا TS9222ID — موازنہ، ڈیزائن رہنمائی، اور تعمیل کی معلومات۔
انتخاب کی گائیڈ
متبادلات کے ساتھ موازنہ
| پیرامیٹر | یہ پروڈکٹ | TS9222IDT | TS9222IPT | TS9222IYPT | TS9222IYDT | TS922ID |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Current Per Channel | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA |
| Input and Output Common-Mode Range | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
اہم امتیازی خصوصیات
- Precision offset specification for the dual SOIC configuration (بمقابلہTS922ID)
- Same electrical family with direct orderable-code flexibility (بمقابلہTS9222IDT)
- Low input bias current for high-impedance sensing (بمقابلہLM2902N/PB)
- Rail-to-rail operation across a wide supply range (بمقابلہLM324ADR)
ڈیزائن نوٹس
Do not assume that rail-to-rail input operation eliminates the need to check common-mode limits under transient conditions. The 500 uV maximum input offset voltage is multiplied by noise gain in a non-inverting amplifier, so a gain of 100 can turn 500 uV into 50 mV of input-referred error. Choose feedback resistors with suitable tolerance, keep input capacitance balanced, and verify the final configuration in the manufacturer datasheet.
Place the supply bypass capacitors immediately beside the TS9222ID supply pins, and connect each capacitor's ground terminal directly to the associated ground plane or pin. Keep feedback resistors and input components close to the amplifier to minimize parasitic capacitance and pickup. For sensitive bridge or current-sense designs, maintain symmetrical input routing and isolate the analog return path from high-current motor, relay, and power-converter returns.
The listed 500 pF capacitive-load capability should be treated as a starting point, not a guarantee for every gain and output configuration. Add a 10 ohm to 100 ohm series isolation resistor when driving long cables, ADC sampling inputs, or loads with uncertain capacitance, then confirm settling and stability on the assembled board. A scope measurement of the output edge will reveal unwanted oscillation or excessive overshoot.
The 2.7 V minimum supply supports 3 V systems, but input and output signal limits change with the actual supply voltage. Do not exceed 12 V, and do not assume the output can reach the positive rail at every load or supply condition. Derive expected headroom from the amplifier's output swing specification, leaving additional margin for temperature, supply tolerance, and fast transient signals.
تعمیل کی معلومات
No explicit compliance declarations were identified for the exact TS9222ID orderable code. Check the current STMicroelectronics product-page declarations and quality-document links before release.