STMicroelectronics

TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics

MPN: TS9222ID ✓ פעיל
2.7 V to 12 V Vdss 80 mA Id 8-SOIC, 0.154 inch width, 3.90 mm length Package
כמות הזמנה מינימלית: 1 |

TS9222ID סקירה

STMicroelectronics TS9222ID is a dual precision operational amplifier optimized for low-noise and stable signal amplification, with rail-to-rail input and output operation, 4 MHz gain-bandwidth product, and 1.3 V/us slew rate in an 8-pin SOIC package. It operates from 2.7 V to 12 V and is specified for -40C to +125C operation.

An operational amplifier is an active analog component that uses high open-loop gain to amplify voltage differences between its differential inputs. Within the analog signal-chain hierarchy, an op amp sits between passive sensor conditioning and higher-level conversion or control functions. Rail-to-rail input and output operation allows the TS9222ID to accept signals near the positive or negative supply rail, while its output can also swing close to those rails.

Key characteristics include a maximum input offset voltage of 500 uV, 80 mA output current per channel, and low input bias current. The 4 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the 1.3 V/us slew rate gives adequate performance for precision feedback networks, instrumentation, and low-to-moderate-frequency signal conditioning. The dual configuration provides two amplifiers in one package, reducing component count on analog boards.

The TS9222ID is built for precision and stability rather than maximum bandwidth. Its 500 uV maximum input offset voltage limits the output error created by input imbalance in a unity-gain configuration. Rail-to-rail inputs help preserve signal integrity in sensor interfaces where the operating point may sit near a supply rail. The stated 80 mA per-channel output capability also allows the amplifier to drive heavier loads than a purely high-impedance signal-processing stage.

Typical applications include current sensing, bridge and instrumentation amplifiers, sensor conditioning, audio preamplification, industrial measurement systems, and automotive electronic modules. The -40C to +125C temperature range supports extended industrial environments, provided that the board-level power supply, bypass capacitors, and stability network follow the manufacturer's recommended implementation.

For reliable operation, place the input and feedback components close to their corresponding pins, bypass each supply rail locally, and verify capacitive-load stability with an isolation resistor when driving cables, ADC inputs, or other long capacitive loads. Use the manufacturer pin-description table when assigning PCB tracks and confirm that the selected amplifier configuration remains stable across the intended gain, load, and supply range.

This page combines package, precision, temperature-range, and interface guidance with same-family drop-in options and a parameter-by-parameter comparison. It is intended to help engineers shorten selection work while preserving the electrical and layout constraints that determine analog performance.

חלופות תחליף ישיר עבור TS9222ID — אותו מארז, תואם פין-לפין. חלקים במארז שונה הדורשים עיבוד מחדש של ה-PCB אינם נכללים.

וריאנטים בסדרה זו

דגמים מאותה סדרה התואמים Drop-in עם TS9222ID (אותו גורם צורה וטביעת רגל) — שונים ב Amplifier Type, Operating Temperature Range, RoHS Status.

STMicroelectronics
Amplifier Type: Standard (General Purpose) Amplifier
Operating Temperature Range: -40 °C to +125 °C
RoHS Status: RoHS Compliant
השווה עם TS9222ID →

TS9222IDT

✅ Drop-In
📦 8-SOIC
Same 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 500 uV maximum offset voltage; orderable packing format differs

📋 חלופה להתייחסות (לא בקטלוג)

TS9222IPT

✅ Drop-In
📦 8-SOIC
Same TS9222 dual-rail-to-rail architecture, 2.7 V to 12 V supply range, and 4 MHz gain-bandwidth product; orderable suffix differs

📋 חלופה להתייחסות (לא בקטלוג)

TS9222IYPT

✅ Drop-In
📦 8-SOIC
Same TS9222 dual-rail-to-rail architecture and 2.7 V to 12 V supply range; qualification and packing suffix differ from TS9222ID

📋 חלופה להתייחסות (לא בקטלוג)

TS9222IYDT

✅ Drop-In
📦 8-SOIC
Same TS9222 family, 4 MHz gain-bandwidth product, and -40C to +125C temperature range; orderable suffix differs

📋 חלופה להתייחסות (לא בקטלוג)

TS922ID

✅ Drop-In
STMicroelectronics
📦 8-SOIC
Standard (General Purpose) Amplifier · 2 · BiCMOS · Rail-to-Rail · Rail-to-Rail · 3 V and 5 V · High output current for low-load impedances · 8-SOIC, Small Outline Integrated Circuit

צור קשר לקבלת מחיר

הצג גיליון נתונים ←

TS9222ID דירוגים מרביים ומאפיינים חשמליים

Amplifier Type General Purpose
Number of Circuits 2 circuits
Number of Amplifiers 2 amplifiers
Supply Voltage Range 2.7 V to 12 V
Gain Bandwidth Product 4 MHz
Slew Rate 1.3 V/us
Input Offset Voltage 500 uV maximum
Output Current Per Channel 80 mA
Input Bias Current 15 nA
Input Common-Mode Rejection Ratio 65 dB
Input Offset Current 0.055 uA
Input Type Rail-to-Rail
סוג פלט Rail-to-Rail
Capacitive Load Drive 500 pF
טווח טמפרטורת פעולה -40C to +125C
מארז 8-SOIC, 0.154 inch width, 3.90 mm length
Packaging Tube
סוג הרכבה Surface mount
סטטוס RoHS unknown

מדריך תצורת פינים של TS9222ID 8-soic, 0.154 inch width, 3.90 mm length

תצורת פינים עבור TS9222ID (מארזת 8-soic, 0.154 inch width, 3.90 mm length). רכיב אנלוגי זה כולל פיני כניסה, יציאה ואספקת מתח. יש לעיין בגיליון הנתונים של היצרן לתצורות פיני איפוס היסט, פיצוי והפעלה. אידיאלי למעגלי עיצוב אותות ומגברים.

תרשים פינים של מארזת 8-soic, 0.154 inch width, 3.90 mm length עבור TS9222ID

אין נתוני פריסת פינים מפורטים עבור TS9222ID.

עיינו ב- גיליון נתונים עבור תצורת פינים מלאה.

יישומים טיפוסיים

TS9222ID מתאים עבור 6 יישוםs: Precision Current Sensing, Bridge Sensor Instrumentation, Industrial Sensor Signal Conditioning, Automotive Control Module Interfaces, Low-Noise Audio Preamplification, Battery and Portable System Buffering.

⚡

Precision Current Sensing

The TS9222ID fits low-side or isolated current-sense amplifiers where input error must remain small. Its 500 uV maximum input offset voltage limits the output error referenced to the shunt voltage, while 15 nA input bias current reduces disturbance in high-impedance sensing networks. The dual configuration can amplify the shunt signal and provide a second channel for an intermediate buffer or reference amplifier. The 4 MHz gain-bandwidth product supports common current-mode gains from 1 to 100, although gain-bandwidth interaction must be checked when operating close to the upper limit.

🏭

Bridge Sensor Instrumentation

The TS9222ID is well matched to resistive bridge sensing because its dual amplifiers can form the two halves of an instrumentation stage. Rail-to-rail input operation accommodates sensor excitation and signal levels that approach the supply rails, while the 1.3 V/us slew rate supports accurate settling of moderate-bandwidth measurements. Use closely matched feedback resistors to preserve common-mode rejection, and keep input traces short and symmetric. The 500 uV maximum offset specification helps control error in gains greater than one, where input offset is multiplied by the noise gain.

🏭

Industrial Sensor Signal Conditioning

The TS9222ID is appropriate for conditioning outputs from pressure, temperature, and position sensors in industrial equipment. Its -40C to +125C operating range covers extended industrial environments, and the rail-to-rail input stage reduces the need to bias signals away from the supply rails. The 4 MHz gain-bandwidth product is sufficient for many slow industrial control loops, while the 80 mA per-channel output current provides headroom for moderate loading. Place the amplifier near the sensor connector when cable capacitance is significant, and add local supply bypassing at the IC pins.

🚗

Automotive Control Module Interfaces

The TS9222ID can serve as a general analog interface amplifier inside automotive control modules because it combines rail-to-rail operation with a -40C to +125C temperature specification. It is suitable for conditioning low-voltage sensor inputs, producing buffered control signals, and amplifying diagnostics signals at moderate frequency. The 500 uV maximum input offset voltage supports accurate sensing, while 15 nA input bias current is useful with high-impedance dividers. Confirm device qualification, transient protection, and supply requirements against the vehicle program before production release.

🎧

Low-Noise Audio Preamplification

The TS9222ID can amplify low-level audio or instrumentation signals when the design requires rail-to-rail input and output operation. The 15 nA input bias current reduces loading on high-impedance sources, and the 4 MHz gain-bandwidth product provides ample bandwidth for typical audio-band feedback networks. The 1.3 V/us slew rate avoids severe distortion on small, low-frequency signals. Place gain-setting and feedback resistors close to the device, maintain short ground returns, and avoid sharing high-current output paths with the input reference.

📱

Battery and Portable System Buffering

The TS9222ID is suitable for buffering sensors and divider outputs in compact battery-powered systems. Operation from 2.7 V supports 3 V supplies, and rail-to-rail input and output stages improve usable signal range in low-voltage designs. The dual package provides two buffers while limiting board area, and 15 nA input bias current is valuable when the source impedance is high. Power consumption should be evaluated in the final gain and load configuration, and the output should not be used to source power for loads beyond the amplifier's normal drive requirement.

What is the operating voltage range of the TS9222ID?
The STMicroelectronics TS9222ID operates from 2.7 V to 12 V. According to the manufacturer datasheet, the device is specified for 3 V and 5 V system rails while tolerating the upper end of its stated supply range. This range suits single-supply instrumentation, industrial control, and automotive signal-conditioning circuits where the amplifier must remain active close to the available supply voltage.
What are the key specifications of TS9222ID that engineers should know?
The TS9222ID is a dual, rail-to-rail precision op amp with a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, 500 uV maximum input offset voltage, and 80 mA output current per channel. It comes in an 8-pin SOIC package and is specified from -40C to +125C. These ratings make it especially relevant to precision feedback loops, sensor interfaces, and industrial or automotive measurement systems.
Where can I download the TS9222ID datasheet PDF?
The TS9222ID datasheet is available through the STMicroelectronics document listings and the manufacturer-linked PDF mirror listed on this page. Use the document to verify the complete electrical characteristics, absolute maximum ratings, pin descriptions, and recommended application circuits before release. Search by the exact orderable code TS9222ID because related suffix codes can identify different packing or temperature options.
Where can I find the TS9222ID pinout and package information?
The TS9222ID is supplied in an 8-pin SOIC package measuring 3.90 mm by 0.154 inch, with pin 1 identified by the standard package orientation mark. Use the pin-description table in the manufacturer datasheet when assigning inputs, outputs, supply rails, and bypass connections. The device provides two amplifiers in the same package, so the two channels do not occupy identical pin positions.
Is TS9222ID suitable for precision sensor conditioning?
Yes, the TS9222ID is suitable for low-to-moderate-frequency precision sensor conditioning. Its 500 uV maximum input offset voltage limits input-referred error, and rail-to-rail inputs are useful when a sensor signal lies near either supply rail. The 4 MHz gain-bandwidth product is appropriate for typical instrumentation and feedback stages, but it is not intended for high-frequency signal chains.
What is the difference between TS9222ID and TS922ID?
The TS9222ID is the newer precision dual-amplifier family, specified with a 4 MHz gain-bandwidth product, 1.3 V/us slew rate, and 500 uV maximum input offset voltage. The older TS922ID belongs to the TS922 family, which is described as optimized for 3 V and 5 V operation with rail-to-rail inputs and outputs. A board-level substitution still requires verification of pin functions, supply limits, stability, and bias-current requirements.
What is the best drop-in replacement for TS9222ID?
The closest same-manufacturer options are TS9222IDT, TS9222IPT, TS9222IYPT, and TS9222IYDT, all documented as members of the TS9222 family in SOIC-8 configurations. Their differences involve orderable suffix, packing, or qualification rather than a different amplifier architecture. Confirm the exact pin arrangement, temperature grade, and delivery format in the manufacturer datasheet before treating any of them as a drop-in replacement.
Can TS9222IDT replace TS9222ID without PCB changes?
TS9222IDT is documented as a TS9222-family SOIC-8 device with the same stated precision characteristics as TS9222ID, including a 4 MHz gain-bandwidth product, 80 mA output current, and 500 uV maximum offset voltage. It is therefore the closest same-device ordering option for an existing tube-format design, subject to confirming the pin functions and orderable-code details in the manufacturer datasheet.
When should I choose TS9222ID over a lower-cost general-purpose op amp?
Choose TS9222ID when offset voltage, rail-to-rail signal handling, low bias current, and an extended -40C to +125C temperature specification are more important than minimum unit cost. Its 500 uV maximum input offset voltage and 15 nA input bias current are particularly useful for high-impedance sensing. For low-cost audio or general buffering applications well inside the common-mode range, a simpler amplifier may be sufficient.
Is the TS9222ID a good replacement for TS9222IYPT?
TS9222ID and TS9222IYPT are both TS9222-family dual precision amplifiers in the same SOIC-8 footprint, with a 2.7 V to 12 V supply range and -40C to +125C operating range. Their orderable suffixes indicate different qualification or delivery options. Before replacing one with the other, verify the pin table, temperature qualification, packing method, and any automotive-specific production requirements.
How much output current can the TS9222ID drive?
The TS9222ID is specified for 80 mA per output channel. This capability exceeds the current required by most high-impedance feedback networks and permits moderate load driving. Output drive alone does not guarantee stability with every load, so check capacitive loading, output current, and supply voltage together. An isolation resistor is recommended when the output drives a long cable or a large input capacitance.
What is the best STMicroelectronics equivalent for TS9222ID?
Among the documented STMicroelectronics alternatives, TS9222IDT is the closest match because it represents the same TS9222 precision dual-amplifier configuration in an 8-pin SOIC package. TS9222IPT, TS9222IYPT, and TS9222IYDT provide related orderable variants. The correct choice depends on whether the key requirement is tube packing, tape-and-reel logistics, or a specific qualification suffix rather than a different electrical function.
How should I decouple the TS9222ID power supply?
Place a local bypass capacitor from each supply pin to the corresponding ground reference, with the shortest possible connection to the package pins. Keep the analog ground return compact and route supply and ground current away from sensitive input nodes. Follow the capacitor values and layout shown in the manufacturer application examples, because excessive trace length or inductance can impair stability and degrade measured noise performance.
Can the TS9222ID drive a 500 pF capacitive load?
Yes, the manufacturer documentation lists a 500 pF capacitive-load drive capability. This makes the device usable with moderately capacitive inputs such as sensor lines, ADC inputs, or short external cables. Stability still depends on gain, output configuration, supply voltage, and load behavior, so verify the actual load and add a series isolation resistor when long cables or unexpected capacitance are present.
Where can I buy TS9222ID and what is its lead time?
Use the Request a Quote form on this page to request current pricing, stock, minimum order quantity, and lead time for TS9222ID. The manufacturer orderable code is supplied in an 8-pin SOIC package, with the TS9222ID suffix identifying the tube-packed configuration. Supply requirements and production schedules can vary by order quantity, so confirm current availability directly before releasing a purchase order.

נתוני עזר הנדסיים עבור TS9222ID — השוואה, הנחיות תכנון ומידע על תאימות.

מדריך בחירה

Choose TS9222ID for precision, low-to-moderate-frequency analog signal conditioning where the 500 uV maximum offset voltage, 15 nA input bias current, rail-to-rail input and output, and -40C to +125C specification justify a dedicated precision amplifier. TS9222IDT is the closest ordering alternative when the same electrical device is needed in a different delivery format; TS9222IPT, TS9222IYPT, and TS9222IYDT are related TS9222 orderable options that require suffix-specific qualification review. Consider TS922ID only when a legacy TS922 footprint is involved and its electrical characteristics have been checked against the circuit. For low-cost, noncritical buffering, LM2902N/PB or LM324ADR may be more appropriate, but their offset, common-mode, and rail-to-rail behavior differ. In every case, confirm pin functions, supply voltage, capacitive-load stability, and temperature requirements before releasing the design.

השוואה עם חלופות

פרמטר מוצר זה TS9222IDT TS9222IPT TS9222IYPT TS9222IYDT TS922ID
Brand STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics STMicroelectronics
Package 8-SOIC 8-SOIC - same footprint 8-SOIC - same footprint 8-SOIC - same footprint 8-SOIC - same footprint 8-SOIC - same footprint
Number of Amplifiers 2 2 2 2 2 2
Output Current Per Channel 80 mA 80 mA 80 mA 80 mA 80 mA 80 mA
Input and Output Common-Mode Range Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output Rail-to-rail input and output

מבדילים עיקריים

  • Precision offset specification for the dual SOIC configuration (לעומתTS922ID)
  • Same electrical family with direct orderable-code flexibility (לעומתTS9222IDT)
  • Low input bias current for high-impedance sensing (לעומתLM2902N/PB)
  • Rail-to-rail operation across a wide supply range (לעומתLM324ADR)

הערות תכנון

Do not assume that rail-to-rail input operation eliminates the need to check common-mode limits under transient conditions. The 500 uV maximum input offset voltage is multiplied by noise gain in a non-inverting amplifier, so a gain of 100 can turn 500 uV into 50 mV of input-referred error. Choose feedback resistors with suitable tolerance, keep input capacitance balanced, and verify the final configuration in the manufacturer datasheet.

Place the supply bypass capacitors immediately beside the TS9222ID supply pins, and connect each capacitor's ground terminal directly to the associated ground plane or pin. Keep feedback resistors and input components close to the amplifier to minimize parasitic capacitance and pickup. For sensitive bridge or current-sense designs, maintain symmetrical input routing and isolate the analog return path from high-current motor, relay, and power-converter returns.

The listed 500 pF capacitive-load capability should be treated as a starting point, not a guarantee for every gain and output configuration. Add a 10 ohm to 100 ohm series isolation resistor when driving long cables, ADC sampling inputs, or loads with uncertain capacitance, then confirm settling and stability on the assembled board. A scope measurement of the output edge will reveal unwanted oscillation or excessive overshoot.

The 2.7 V minimum supply supports 3 V systems, but input and output signal limits change with the actual supply voltage. Do not exceed 12 V, and do not assume the output can reach the positive rail at every load or supply condition. Derive expected headroom from the amplifier's output swing specification, leaving additional margin for temperature, supply tolerance, and fast transient signals.

מידע על תאימות

RoHS
Unknown
REACH
Unknown
AEC-Q100
Unknown
נטול עופרת
Unknown
נטול הלוגנים
Unknown
מינרלים של סכסוך
Unknown

No explicit compliance declarations were identified for the exact TS9222ID orderable code. Check the current STMicroelectronics product-page declarations and quality-document links before release.

הנתונים אומתו בתאריך: 2026-11-16 — נתונים אומתו ונערכו על ידי צוות הנדסת הרכיבים של XAIPART

חיפושים קשורים

TS9222ID datasheet TS9222ID pinout TS9222ID datasheet pdf TS9222ID specifications STMicroelectronics TS9222ID TS9222ID equivalent TS9222ID replacement TS9222ID cross reference TS9222ID vs TS922ID TS9222ID 4MHz dual op amp TS9222ID SOIC-8 pinout TS9222ID rail-to-rail amplifier TS9222ID current sensing application TS9222ID price TS9222ID stock

רכיבים ומונחים קשורים

STMicroelectronics TS9222ID TS9222IDT TS9222IPT TS9222IYPT TS9222IYDT TS922ID operational amplifier dual precision amplifier rail-to-rail input rail-to-rail output input offset voltage input bias current gain-bandwidth product slew rate common-mode rejection ratio 8-SOIC SOIC package family surface-mount package instrumentation amplifier current-sense amplifier sensor conditioning automotive electronics industrial electronics
בקשת הצעת מחיר מהירה
מלא את כל הפרטים — צוות המכירות שלנו יגיב תוך 24 שעות
מספר חלק יצרן מארז QTY מחיר יעד סה"כ
✓
הצעת המחיר נשלחה!

נשיב לדוא"ל שלך בתוך 24 שעות

1
בקשת הצעת מחיר נשלחה
2
הצעת מחיר התקבלה
3
ההזמנה בוצעה
4
תשלום
5
נשלח
6
נמסר
צפה בפרטי בקשת הצעת המחיר