TS9222ID - Dual Precision Rail-to-Rail Op Amp | STMicroelectronics
N.º de pieza: TS9222ID ✓ ActivoTS9222ID Descripción general
An operational amplifier is an active analog component that uses high open-loop gain to amplify voltage differences between its differential inputs. Within the analog signal-chain hierarchy, an op amp sits between passive sensor conditioning and higher-level conversion or control functions. Rail-to-rail input and output operation allows the TS9222ID to accept signals near the positive or negative supply rail, while its output can also swing close to those rails.
Key characteristics include a maximum input offset voltage of 500 uV, 80 mA output current per channel, and low input bias current. The 4 MHz gain-bandwidth product supports closed-loop operation at moderate signal frequencies, while the 1.3 V/us slew rate gives adequate performance for precision feedback networks, instrumentation, and low-to-moderate-frequency signal conditioning. The dual configuration provides two amplifiers in one package, reducing component count on analog boards.
The TS9222ID is built for precision and stability rather than maximum bandwidth. Its 500 uV maximum input offset voltage limits the output error created by input imbalance in a unity-gain configuration. Rail-to-rail inputs help preserve signal integrity in sensor interfaces where the operating point may sit near a supply rail. The stated 80 mA per-channel output capability also allows the amplifier to drive heavier loads than a purely high-impedance signal-processing stage.
Typical applications include current sensing, bridge and instrumentation amplifiers, sensor conditioning, audio preamplification, industrial measurement systems, and automotive electronic modules. The -40C to +125C temperature range supports extended industrial environments, provided that the board-level power supply, bypass capacitors, and stability network follow the manufacturer's recommended implementation.
For reliable operation, place the input and feedback components close to their corresponding pins, bypass each supply rail locally, and verify capacitive-load stability with an isolation resistor when driving cables, ADC inputs, or other long capacitive loads. Use the manufacturer pin-description table when assigning PCB tracks and confirm that the selected amplifier configuration remains stable across the intended gain, load, and supply range.
This page combines package, precision, temperature-range, and interface guidance with same-family drop-in options and a parameter-by-parameter comparison. It is intended to help engineers shorten selection work while preserving the electrical and layout constraints that determine analog performance.
Alternativas directas para TS9222ID — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con TS9222ID (mismo factor de forma y huella) — difiere en Amplifier Type, Operating Temperature Range, RoHS Status.
TS9222IDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS9222IPT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS9222IYPT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS9222IYDT
✅ Sustitución directa📋 Alternativa de referencia (no en el catálogo)
TS922ID
✅ Sustitución directaConsulte el precio
Ver hoja de datos →TS9222ID Valores máximos y características eléctricas
| Amplifier Type | General Purpose |
| Number of Circuits | 2 circuits |
| Number of Amplifiers | 2 amplifiers |
| Supply Voltage Range | 2.7 V to 12 V |
| Gain Bandwidth Product | 4 MHz |
| Slew Rate | 1.3 V/us |
| Input Offset Voltage | 500 uV maximum |
| Output Current Per Channel | 80 mA |
| Input Bias Current | 15 nA |
| Input Common-Mode Rejection Ratio | 65 dB |
| Input Offset Current | 0.055 uA |
| Input Type | Rail-to-Rail |
| Tipo de salida | Rail-to-Rail |
| Capacitive Load Drive | 500 pF |
| Rango de temperatura de funcionamiento | -40C to +125C |
| Encapsulado | 8-SOIC, 0.154 inch width, 3.90 mm length |
| Packaging | Tube |
| Tipo de montaje | Surface mount |
| Estado RoHS | unknown |
Guía de configuración de pines de TS9222ID 8-soic, 0.154 inch width, 3.90 mm length
Configuración de pines para TS9222ID (encapsulado 8-soic, 0.154 inch width, 3.90 mm length). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para TS9222ID.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
TS9222ID es adecuado para 6 aplicacións: Precision Current Sensing, Bridge Sensor Instrumentation, Industrial Sensor Signal Conditioning, Automotive Control Module Interfaces, Low-Noise Audio Preamplification, Battery and Portable System Buffering.
Precision Current Sensing
The TS9222ID fits low-side or isolated current-sense amplifiers where input error must remain small. Its 500 uV maximum input offset voltage limits the output error referenced to the shunt voltage, while 15 nA input bias current reduces disturbance in high-impedance sensing networks. The dual configuration can amplify the shunt signal and provide a second channel for an intermediate buffer or reference amplifier. The 4 MHz gain-bandwidth product supports common current-mode gains from 1 to 100, although gain-bandwidth interaction must be checked when operating close to the upper limit.
Recomendado
Bridge Sensor Instrumentation
The TS9222ID is well matched to resistive bridge sensing because its dual amplifiers can form the two halves of an instrumentation stage. Rail-to-rail input operation accommodates sensor excitation and signal levels that approach the supply rails, while the 1.3 V/us slew rate supports accurate settling of moderate-bandwidth measurements. Use closely matched feedback resistors to preserve common-mode rejection, and keep input traces short and symmetric. The 500 uV maximum offset specification helps control error in gains greater than one, where input offset is multiplied by the noise gain.
Recomendado
Industrial Sensor Signal Conditioning
The TS9222ID is appropriate for conditioning outputs from pressure, temperature, and position sensors in industrial equipment. Its -40C to +125C operating range covers extended industrial environments, and the rail-to-rail input stage reduces the need to bias signals away from the supply rails. The 4 MHz gain-bandwidth product is sufficient for many slow industrial control loops, while the 80 mA per-channel output current provides headroom for moderate loading. Place the amplifier near the sensor connector when cable capacitance is significant, and add local supply bypassing at the IC pins.
Recomendado
Automotive Control Module Interfaces
The TS9222ID can serve as a general analog interface amplifier inside automotive control modules because it combines rail-to-rail operation with a -40C to +125C temperature specification. It is suitable for conditioning low-voltage sensor inputs, producing buffered control signals, and amplifying diagnostics signals at moderate frequency. The 500 uV maximum input offset voltage supports accurate sensing, while 15 nA input bias current is useful with high-impedance dividers. Confirm device qualification, transient protection, and supply requirements against the vehicle program before production release.
Recomendado
Low-Noise Audio Preamplification
The TS9222ID can amplify low-level audio or instrumentation signals when the design requires rail-to-rail input and output operation. The 15 nA input bias current reduces loading on high-impedance sources, and the 4 MHz gain-bandwidth product provides ample bandwidth for typical audio-band feedback networks. The 1.3 V/us slew rate avoids severe distortion on small, low-frequency signals. Place gain-setting and feedback resistors close to the device, maintain short ground returns, and avoid sharing high-current output paths with the input reference.
Recomendado
Battery and Portable System Buffering
The TS9222ID is suitable for buffering sensors and divider outputs in compact battery-powered systems. Operation from 2.7 V supports 3 V supplies, and rail-to-rail input and output stages improve usable signal range in low-voltage designs. The dual package provides two buffers while limiting board area, and 15 nA input bias current is valuable when the source impedance is high. Power consumption should be evaluated in the final gain and load configuration, and the output should not be used to source power for loads beyond the amplifier's normal drive requirement.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para TS9222ID — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | TS9222IDT | TS9222IPT | TS9222IYPT | TS9222IYDT | TS922ID |
|---|---|---|---|---|---|---|
| Brand | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics | STMicroelectronics |
| Package | 8-SOIC | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint | 8-SOIC - same footprint |
| Number of Amplifiers | 2 | 2 | 2 | 2 | 2 | 2 |
| Output Current Per Channel | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA | 80 mA |
| Input and Output Common-Mode Range | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output | Rail-to-rail input and output |
Diferenciadores clave
- Precision offset specification for the dual SOIC configuration (frente a TS922ID)
- Same electrical family with direct orderable-code flexibility (frente a TS9222IDT)
- Low input bias current for high-impedance sensing (frente a LM2902N/PB)
- Rail-to-rail operation across a wide supply range (frente a LM324ADR)
Notas de diseño
Do not assume that rail-to-rail input operation eliminates the need to check common-mode limits under transient conditions. The 500 uV maximum input offset voltage is multiplied by noise gain in a non-inverting amplifier, so a gain of 100 can turn 500 uV into 50 mV of input-referred error. Choose feedback resistors with suitable tolerance, keep input capacitance balanced, and verify the final configuration in the manufacturer datasheet.
Place the supply bypass capacitors immediately beside the TS9222ID supply pins, and connect each capacitor's ground terminal directly to the associated ground plane or pin. Keep feedback resistors and input components close to the amplifier to minimize parasitic capacitance and pickup. For sensitive bridge or current-sense designs, maintain symmetrical input routing and isolate the analog return path from high-current motor, relay, and power-converter returns.
The listed 500 pF capacitive-load capability should be treated as a starting point, not a guarantee for every gain and output configuration. Add a 10 ohm to 100 ohm series isolation resistor when driving long cables, ADC sampling inputs, or loads with uncertain capacitance, then confirm settling and stability on the assembled board. A scope measurement of the output edge will reveal unwanted oscillation or excessive overshoot.
The 2.7 V minimum supply supports 3 V systems, but input and output signal limits change with the actual supply voltage. Do not exceed 12 V, and do not assume the output can reach the positive rail at every load or supply condition. Derive expected headroom from the amplifier's output swing specification, leaving additional margin for temperature, supply tolerance, and fast transient signals.
Información de cumplimiento
No explicit compliance declarations were identified for the exact TS9222ID orderable code. Check the current STMicroelectronics product-page declarations and quality-document links before release.