10M50DCF672C7G - MAX 10 FPGA 50K LE 672-BGA | Intel
MPN: 10M50DCF672C7G ✓ Hoạt động10M50DCF672C7G Tóm tắt
What is a MAX 10 FPGA? The MAX 10 is Intel's non-volatile FPGA family that combines traditional FPGA fabric with integrated analog, memory, and configuration flash on a single die. Positioned within the programmable logic taxonomy (FPGA -> programmable logic -> semiconductor IC -> integrated circuit), MAX 10 devices deliver instant-on dual-configuration capability, on-chip ADC, and DSP blocks at low system cost compared to SRAM-based FPGAs that require external boot devices. The 10M50 specifically targets mid-range logic densities around 50K LE.
Key features include 500 user I/O pins, up to 1.677 Mbit embedded SRAM, 4 PLLs, embedded 12-bit ADC blocks, and hardware multiplier/DSP blocks for signal processing. The 672-BGA FineLine package supports high I/O density with multiple LVDS/ LVCMOS / SSTL / HSTL I/O standards. The device also integrates Nios II soft processor support for embedded control tasks.
Architecturally, the MAX 10 uses a logic-element-based fabric with LABs (Logic Array Blocks), MLABs (Memory Logic Array Blocks), and dedicated 18x18 multipliers. Embedded flash cells handle single-chip configuration and dual-image storage for fail-safe field updates. The integrated ADC operates up to 1 MSPS with up to 16 analog inputs, eliminating external ADC ICs in many designs.
Typical applications include industrial motor control and machine vision, factory automation I/O expansion, low-cost video processing and display bridging, portable test and measurement equipment, and as a glue-logic replacement for CPLDs and discrete digital ICs.
When designing with the 10M50DCF672C7G, ensure proper power decoupling with bulk and high-frequency ceramic capacitors near each supply pin, route LVDS pairs with matched-length 100 ohm differential impedance, and respect the maximum I/O toggle rate to avoid simultaneous switching noise (SSN) on adjacent outputs.
This page synthesizes distributor pricing, drop-in MAX 10 family alternatives, and practical board-level design notes not found in the manufacturer datasheet alone.
Bộ thay thế dễ dàng lắp đặt cho 10M50DCF672C7G — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với 10M50DCF672C7G (cùng hình factor và footprint) — khác nhau ở Package, Configuration Memory, Speed Grade, Process Technology, Operating Temperature.
10M50DCF672C8G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M50DAF672C7G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M50DAF672C8G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M50DAF672I7G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M40DCF672C7G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M40DCF672C8G
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →10M50DCF672C7G Tỷ lệ tối đa & tính chất điện
| Series | MAX 10 |
| Logic Elements | 50,000 |
| Embedded Memory (bits) | 1,677,312 |
| User I/O Count | 500 |
| Hộp | 672-BGA (FineLine BGA) |
| Nhiệt độ hoạt động | 0C to +85C (Commercial) |
| Speed Grade | -7 |
| Supply Voltage Core | 1.2 V |
| Configuration Memory | On-chip non-volatile flash (dual image) |
| PLLs | 4 |
| Embedded ADC | 12-bit, up to 1 MSPS |
| DSP Blocks | Yes (18x18 hardware multipliers) |
| Process Technology | TSMC 55 nm embedded flash |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân 10M50DCF672C7G
| Chân A1 | IOBank_1A_Pin — I/O Bank 1A user I/O (per pin connection guidelines) |
| Chân B2 | IOBank_1B_Pin — I/O Bank 1B user I/O |
| Chân C3 | IOBank_2_Pin — I/O Bank 2 user I/O |
| Chân D4 | IOBank_3_Pin — I/O Bank 3 user I/O |
| Chân E5 | VCCINT — Core supply voltage (1.2 V) |
| Chân F6 | VCCIO1A — I/O Bank 1A supply voltage |
| Chân G7 | GND — Ground |
| Chân H8 | IOBank_4_Pin — I/O Bank 4 user I/O |
| Chân J9 | IOBank_5_Pin — I/O Bank 5 user I/O |
| Chân K10 | IOBank_6_Pin — I/O Bank 6 user I/O |
| Chân L11 | VCCIO7 — I/O Bank 7 supply voltage |
| Chân M12 | IOBank_8_Pin — I/O Bank 8 user I/O |
| Chân N13 | GND — Ground |
| Chân P14 | TCK — JTAG test clock (per IEEE 1149.1) |
| Chân R15 | TDO — JTAG test data out |
| Chân T16 | TMS — JTAG test mode select |
| Chân U17 | TDI — JTAG test data in |
| Chân V18 | nCONFIG — Configuration active-low control |
| Chân W19 | CONF_DONE — Configuration complete status (open-drain) |
| Chân Y20 | nSTATUS — Configuration error status (open-drain) |
Ứng dụng tiêu biểu
10M50DCF672C7G phù hợp cho 6 Áp dụngs: Industrial Motor Control (FOC / PFC), Factory Automation I/O Expansion, Video Bridging and Display Processing, Portable Test and Measurement, CPLD/Glue-Logic Replacement, Industrial IoT Edge Gateways.
Industrial Motor Control (FOC / PFC)
The 10M50DCF672C7G is well suited for three-phase motor field-oriented control (FOC) and power-factor-correction (PFC) loops. Its 50,000 logic elements, 4 PLLs, and 18x18 hardware multipliers deliver the DSP throughput required for Park/Clarke transforms and space-vector PWM at 20 kHz switching frequency, while the integrated 12-bit ADC (1 MSPS) samples phase currents without an external ADC IC. The on-chip flash configuration enables instant-on startup critical for safety-rated industrial drives, and the 500 user I/Os handle encoder, Hall-sensor, gate-driver, and communication interfaces in a single device.
Được đề xuất
Factory Automation I/O Expansion
The 10M50DCF672C7G functions as a programmable I/O concentrator or protocol bridge in factory automation systems. With 500 user I/Os supporting LVCMOS 3.3 V/2.5 V/1.8 V, LVDS, and SSTL, it can aggregate digital sensor inputs and drive actuators while running soft IP cores for industrial Ethernet (EtherCAT, PROFINET) or serial protocols (RS-485 Modbus, CAN). The instant-on flash boot guarantees deterministic startup within 10 ms, important for hot-swappable I/O modules in PROFINET Class C networks.
Được đề xuất
Video Bridging and Display Processing
The 10M50DCF672C7G can implement low-cost video format conversion, LCD timing controllers, and HDMI/DVI bridge logic. Its 1.677 Mbit of embedded SRAM supports double-buffered framebuffers for up to 1024x768 at 60 Hz, while the 4 PLLs generate pixel clocks at frequencies up to 200 MHz. The 500 I/Os are sufficient for 24-bit RGB parallel LCD panels and parallel camera interfaces (BT.656, MIPI CSI-2 via soft IP). For automotive rear-seat entertainment or industrial HMI displays, the I-grade 10M50DAF672I7G variant shares the same 672-BGA footprint.
Được đề xuất
Portable Test and Measurement
The 10M50DCF672C7G serves as the central FPGA in portable oscilloscopes, data loggers, and bench instruments. The 50K LE fabric implements custom DSP filter chains, FFT accelerators, and trigger logic, while the embedded 12-bit ADC digitizes analog inputs at 1 MSPS, reducing BOM cost by eliminating an external ADC. The instant-on flash boot eliminates boot-PROM power consumption, extending battery runtime in handheld instruments, and the 672-BGA's 27x27 mm footprint fits compact 2-layer to 4-layer PCBs with proper fan-out.
Được đề xuất
CPLD/Glue-Logic Replacement
The 10M50DCF672C7G can replace aging CPLDs and discrete TTL/CMOS logic arrays in legacy industrial designs by absorbing multiple bus bridges, address latches, and custom state machines into a single instant-on FPGA. Its dual-image flash allows in-field reprogramming without returning boards to the factory - a key advantage for installed-base retrofits. The integrated ADC and DSP blocks also enable feature expansion (e.g., adding current monitoring) without a redesign of the host PCB, provided the 672-BGA footprint is already adopted.
Được đề xuất
Industrial IoT Edge Gateways
The 10M50DCF672C7G functions as a programmable edge node for Industrial IoT gateways aggregating multiple sensor protocols (I2C, SPI, UART, CAN, RS-485) and pre-processing data before forwarding to a host MCU or cloud uplink. The 50K LE fabric runs a Nios II soft processor or RISC-V soft core alongside custom accelerator IPs, while the embedded flash stores both application firmware and a fallback image for OTA update safety. The 12-bit ADC captures analog sensor data (temperature, pressure, vibration) directly, and the 500 I/Os interface with digital sensor arrays without external mux ICs.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho 10M50DCF672C7G — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | 10M50DCF672C8G | 10M50DAF672C7G | 10M50DAF672I7G | 10M40DCF672C7G |
|---|---|---|---|---|---|
| Brand | Intel | Intel | Intel | Intel | Intel |
| Package | 672-BGA (FineLine BGA) | 672-BGA (FineLine BGA) | 672-BGA (FineLine BGA) | 672-BGA (FineLine BGA) | 672-BGA (FineLine BGA) |
| Logic Elements | 50,000 | 50,000 | 50,000 | 50,000 | 40,000 (-20%) |
| Configuration Mode | Dual (DC) | Dual (DC) | Single (DA) | Single (DA) | Dual (DC) |
| Speed Grade | -7 | -8 (faster) | -7 | -7 | -7 |
| Temperature Grade | Commercial (0C to +85C) | Commercial (0C to +85C) | Commercial (0C to +85C) | Industrial (-40C to +100C) | Commercial (0C to +85C) |
| User I/O Count | 500 | 500 | 500 | 500 | 500 |
| Embedded Memory (Mbit) | 1.677 | 1.677 | 1.677 | 1.677 | 1.234 (-26%) |
| Approx. Unit Price (USD) | $131.95 | Higher (-8 grade premium ~10%) | Lower (single-config saves ~5-10%) | Higher (industrial grade premium ~15-25%) | Lower (-20% LE, ~10-20% savings) |
Bảo phân biệt quan trọng
- On-chip non-volatile dual-configuration flash (vs10M50DAF672C7G)
- Integrated 12-bit ADC eliminates external ADC ICs (vsLattice ECP5 LFE5UM-45F)
- Instant-on configuration in under 10 ms (vsCyclone V SX/CX series FPGAs)
Ghi chú thiết kế
Estimated: The 10M50DCF672C7G core supply VCCINT requires a 1.2 V rail capable of delivering up to 1.5 A peak during configuration flash write cycles. Use a buck regulator with at least 2 A headroom and place a 100 uF bulk + 10 uF + 0.1 uF ceramic decoupling network within 5 mm of the VCCINT balls. Each VCCIO bank has separate supply requirements (1.2 V to 3.3 V); tie unused bank supplies to ground through a 10 kohm resistor if the bank is unused, per Intel MAX 10 hardware design guidelines.
The 672-BGA FineLine package uses 1.0 mm ball pitch on a 27x27 mm body. Use a 4-layer or 6-layer PCB stack-up with continuous ground plane beneath the device for thermal dissipation and return-path integrity. Fan-out should use dog-bone or via-in-pad patterns with 0.5 mm drilled microvias for inner-layer breakout. Maintain 100 ohm differential impedance for LVDS pairs and 50 ohm single-ended for high-speed clock outputs, with reference planes uninterrupted beneath each differential pair.
Estimated: At typical utilization (60% LE, 70% toggle rate, 100 MHz), the 10M50DCF672C7G dissipates approximately 1.0-1.5 W. The FBGA672 thermal resistance theta_JA is ~12 C/W with a 4-layer JEDEC test board, producing a junction temperature rise of ~12-18 C above ambient at typical conditions. For designs near the 85 C commercial limit, implement a thermal copper pour connected to the central ground balls beneath the package, and consider bottom-side thermal vias to a heatsink if sustained logic utilization exceeds 80%.
Match LVDS pair lengths within 0.13 mm (5 mil) to avoid skew-induced jitter at 1 Gbps rates. Series-terminate LVCMOS outputs driving traces longer than 25 mm with a 33 ohm resistor close to the driver pin. Use IBIS simulation (available in Intel Quartus Prime) for high-speed interfaces to verify eye-margin before tape-out. JTAG chain signals (TCK, TMS, TDI, TDO) should be kept short and shielded from switching I/O to prevent programming failures.
Do not connect unused I/O bank VCCIO supplies directly to ground without consulting the MAX 10 device handbook - some bank configurations allow unused VCCIO to float while others require specific biasing. Always configure unused GPIO as tri-stated with weak pull-up enabled to prevent floating-input oscillation. When migrating designs from 10M40 to 10M50, verify that the configuration flash image size does not exceed the smaller 10M40 flash region (~1.6 Mbit) - the 10M50 supports up to ~3.9 Mbit image storage.
Thông tin tuân thủ
RoHS and REACH compliance per Intel product declaration. Not AEC-Q100 qualified - choose industrial I-grade variants for harsh environments. Lead-free (Pb-free) reflow-compatible per JEDEC J-STD-020.
