AD510JH/+ - 100V/us Precision Operational Amplifier | Analog Devices
MPN: AD510JH/+ ✗ Cuối đờiAD510JH/+ Tóm tắt
An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, or compare small analog signals. The AD510 belongs to the precision op-amp hierarchy, where low offset voltage, low bias current, and high open-loop gain are prioritized over rail-to-rail operation or wide common-mode range. Its 10 nV/sqrt(Hz) input-noise specification makes it suitable for instrumentation and sensor-interface circuits where the input signal is small relative to system noise.
Key electrical characteristics include 100 V/us slew rate, 100 uV maximum input offset voltage, 25 nA maximum input bias current, 5 nA maximum input offset current, and 3 uV/C input offset temperature drift. The amplifier operates over a 0 C to +70 C temperature range and is specified for 10 mA output current. Built-in compensation removes the need for an external compensation network in standard voltage-amplifier configurations.
The AD510 uses a bipolar input architecture, which contributes to its low-noise precision characteristics but requires suitable supply headroom for the chosen output range. The TO-99-8 package is a hermetically sealed, leaded metal-can format commonly associated with older precision analog equipment. Its mechanical format is substantially different from modern surface-mount op-amp packages, so board layout, insertion tooling, and replacement planning must account for the 8-pin cylindrical footprint.
Typical applications include low-level sensor amplification, laboratory instrumentation, process-control loops, bridge-amplifier interfaces, and precision current-to-voltage converters. Its 94 dB open-loop gain supports accurate closed-loop gain when feedback-network resistors are chosen with suitable tolerances. The 100 V/us slew rate also allows faithful reproduction of moderately fast waveforms without external compensation.
For stable operation, follow the recommended feedback and decoupling arrangements in the manufacturer datasheet. Decoupling capacitors should connect close to the supply pins, and unused inputs should be tied to a defined potential rather than left floating. Because this is a bipolar precision amplifier, verify output swing, common-mode range, and load current against the actual supply voltage before finalizing the circuit.
This page consolidates device specifications, package details, comparison information, and practical application guidance for engineers evaluating the AD510JH/+ in legacy or maintenance-oriented analog designs.
Bộ thay thế dễ dàng lắp đặt cho AD510JH/+ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD510JH/+ (cùng hình factor và footprint) — khác nhau ở Mounting Type, Package.
AD510JH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
OP-27CJ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MXL1001ACH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD510JH/+ Tỷ lệ tối đa & tính chất điện
| Number of Channels | 1 channel |
| Amplifier Type | General-purpose operational amplifier |
| Slew Rate | 100 V/us |
| Maximum Input Offset Voltage | 100 uV |
| Output Current | 10 mA |
| Input Voltage Noise Density | 10 nV/sqrt(Hz) at 1 kHz |
| Maximum Input Bias Current | 25 nA |
| Input Offset Temperature Drift | 3 uV/C |
| Điện áp cung cấp | 4 mA |
| Maximum Input Offset Current | 5 nA |
| Open-Loop Gain | 94 dB |
| Compensation | Built-in |
| Khoảng nhiệt độ hoạt động | 0 C to +70 C |
| Input Architecture | Bipolar |
| Hộp | TO-99-8 |
| Kiểu lắp đặt | Leaded, metal can |
Hướng dẫn cấu hình chân AD510JH/+ to-99-8
Cấu hình chân cho AD510JH/+ (to-99-8 gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD510JH/+.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD510JH/+ phù hợp cho 6 Áp dụngs: Precision Sensor Signal Conditioning, Strain-Gauge Bridge Instrumentation, Laboratory Measurement Instruments, Process-Control Loop Amplification, Current-to-Voltage Conversion, Legacy Test and Measurement Equipment.
Precision Sensor Signal Conditioning
The AD510JH/+ suits low-level sensor conditioning because its 100 uV maximum input offset and 25 nA maximum input bias current limit errors in high-impedance sources. Its 10 nV/sqrt(Hz) input-noise density at 1 kHz also supports careful extraction of small signals. Place it in a non-inverting or differential stage with matched feedback resistors, and calculate the bias-current error against the actual sensor impedance before finalizing the gain.
Được đề xuất
Strain-Gauge Bridge Instrumentation
A strain-gauge bridge produces a small differential signal that the AD510JH/+ can amplify with its 94 dB open-loop gain and built-in compensation. The device's 25 nA maximum bias current is particularly relevant when the bridge impedance is high, while its 3 uV/C offset drift contributes directly to span error. Match the amplifier inputs and feedback network carefully, and include input-bias and thermal-drift errors in the instrument calibration budget.
Được đề xuất
Laboratory Measurement Instruments
The AD510JH/+ is appropriate for laboratory instruments that amplify small voltages around a system reference, including source-measurement and calibration interfaces. Its 100 V/us slew rate preserves moderately fast signal transitions, while internally compensated operation simplifies the implementation of standard closed-loop amplifiers. Use the TO-99-8 construction when maintaining vintage instrument designs, and route supply bypassing close to the device to limit noise pickup.
Được đề xuất
Process-Control Loop Amplification
The AD510JH/+ can amplify a low-level error signal in legacy process-control equipment where the loop requires high open-loop gain and controlled offset. Its 94 dB open-loop gain supports accurate feedback performance, and the 100 V/us slew rate allows satisfactory response to many slow control signals. Verify the sensor output range against the amplifier's input common-mode limits and the actuator demand against its output-swing capability.
Được đề xuất
Current-to-Voltage Conversion
The AD510JH/+ is useful in transimpedance stages for photodiode, optical-power, or electrochemical sensors because low bias current reduces current-conversion error. Its 100 uV maximum offset establishes a meaningful limit for small output voltages, while the 94 dB open-loop gain improves loop control in the inverting configuration. Add the required feedback compensation capacitance and check stability at the intended gain before increasing the transimpedance value.
Được đề xuất
Legacy Test and Measurement Equipment
The TO-99-8 AD510JH/+ is well suited to repair and modernization of older test equipment that used hermetically sealed precision analog packages. Its 100 V/us slew rate, 94 dB open-loop gain, and 0 C to +70 C commercial range align with many laboratory and industrial instruments. Maintain the original 8-lead metal-can footprint or redesign explicitly, and validate offset, bias current, noise, and supply behavior against the original circuit.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD510JH/+ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD510JH | OP-27CJ | MXL1001ACH |
|---|---|---|---|---|
| Package | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
Bảo phân biệt quan trọng
- Closest documented ordering alternative (vsAD510JH)
- Higher documented open-loop gain than generic comparison candidates (vsOP-27CJ)
- Defined noise and thermal-drift values for precision error budgeting (vsMXL1001ACH)
Ghi chú thiết kế
Design the supply rails so the AD510JH/+ retains adequate input common-mode range and output-swing margin at every operating point. The device has a bipolar input architecture and is characterized at approximately 4 mA supply current. Place supply-bypass capacitors close to the device leads and use separate return paths for input and output to reduce supply-induced offset and noise pickup.
Do not treat the TO-99-8 metal-can package as interchangeable with an SOIC or DIP footprint solely because both are eight-pin devices. Check lead spacing, body diameter, pin numbering, and the manufacturer pin-description table. The AD510JH ordering form is the closest documented match, while OP-27CJ and MXL1001ACH still require verification of pin mapping, bias current, compensation, and supply behavior.
For high-impedance sensor inputs, calculate the bias-current contribution using the source impedance and compare it with the AD510JH/+ specification of 25 nA maximum input bias current. Keep sensitive input traces short, guard high-impedance nodes where practical, and use matched feedback resistors. Include the specified 3 uV/C offset drift and 100 uV maximum offset in the total measurement-error budget.
Route the inverting and non-inverting connections away from supply pins and high-current output paths. Use a compact ground reference beneath the analog section and connect bypass-capacitor returns directly to the device ground pins. Since this is a leaded hermetically sealed package, also account for insertion stress and provide adequate clearance from tall adjacent components during legacy-board assembly and maintenance.
Thông tin tuân thủ
The TO-99-8 hermetically sealed package predates current surface-mount lead-free practices. No explicit RoHS, REACH, halogen-free, or conflict-minerals declarations were identified, so these fields remain unknown.