AD510JH/+ - 100V/us Precision Operational Amplifier | Analog Devices
MPN: AD510JH/+ ✗ کۆتایی ژیانAD510JH/+ گشتی
An operational amplifier is a voltage-gain building block used to amplify, buffer, filter, or compare small analog signals. The AD510 belongs to the precision op-amp hierarchy, where low offset voltage, low bias current, and high open-loop gain are prioritized over rail-to-rail operation or wide common-mode range. Its 10 nV/sqrt(Hz) input-noise specification makes it suitable for instrumentation and sensor-interface circuits where the input signal is small relative to system noise.
Key electrical characteristics include 100 V/us slew rate, 100 uV maximum input offset voltage, 25 nA maximum input bias current, 5 nA maximum input offset current, and 3 uV/C input offset temperature drift. The amplifier operates over a 0 C to +70 C temperature range and is specified for 10 mA output current. Built-in compensation removes the need for an external compensation network in standard voltage-amplifier configurations.
The AD510 uses a bipolar input architecture, which contributes to its low-noise precision characteristics but requires suitable supply headroom for the chosen output range. The TO-99-8 package is a hermetically sealed, leaded metal-can format commonly associated with older precision analog equipment. Its mechanical format is substantially different from modern surface-mount op-amp packages, so board layout, insertion tooling, and replacement planning must account for the 8-pin cylindrical footprint.
Typical applications include low-level sensor amplification, laboratory instrumentation, process-control loops, bridge-amplifier interfaces, and precision current-to-voltage converters. Its 94 dB open-loop gain supports accurate closed-loop gain when feedback-network resistors are chosen with suitable tolerances. The 100 V/us slew rate also allows faithful reproduction of moderately fast waveforms without external compensation.
For stable operation, follow the recommended feedback and decoupling arrangements in the manufacturer datasheet. Decoupling capacitors should connect close to the supply pins, and unused inputs should be tied to a defined potential rather than left floating. Because this is a bipolar precision amplifier, verify output swing, common-mode range, and load current against the actual supply voltage before finalizing the circuit.
This page consolidates device specifications, package details, comparison information, and practical application guidance for engineers evaluating the AD510JH/+ in legacy or maintenance-oriented analog designs.
جێگرەوەکانی جێگۆڕکێ بۆ AD510JH/+ — هەمان پاکەت، پین بە پین گونجاو. ئەو بەشانەی پاکەتی جیاوازیان هەیە و پێویستیان بە چاککردنەوەی PCB هەیە لابراون.
جۆرەکان لەم زنجیرەیەدا
مۆدێلەکانی هەمان زنجیرە کە بە شێوەی ڕاستەوخۆ گونجاون لەگەڵ AD510JH/+ (هەمان شێوە و پێکهاتەی شوێن) — جیاوازە لە Mounting Type, Package.
AD510JH
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
OP-27CJ
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
MXL1001ACH
✅ جێگرەوەی ڕاستەوخۆ📋 جێگرەوەی سەرچاوە (لە کاتالۆگدا نییە)
AD510JH/+ زۆرترین ڕێژە و تایبەتمەندییە کارەباییەکان
| Number of Channels | 1 channel |
| Amplifier Type | General-purpose operational amplifier |
| Slew Rate | 100 V/us |
| Maximum Input Offset Voltage | 100 uV |
| Output Current | 10 mA |
| Input Voltage Noise Density | 10 nV/sqrt(Hz) at 1 kHz |
| Maximum Input Bias Current | 25 nA |
| Input Offset Temperature Drift | 3 uV/C |
| ئێستای دابینکردن | 4 mA |
| Maximum Input Offset Current | 5 nA |
| Open-Loop Gain | 94 dB |
| Compensation | Built-in |
| مەودای پلەی گەرمیی کارکردن | 0 C to +70 C |
| Input Architecture | Bipolar |
| پاکێج | TO-99-8 |
| جۆری دامەزراندن | Leaded, metal can |
ڕێنمایی ڕێکخستنی پینی AD510JH/+ to-99-8
ڕێکخستنی پین بۆ AD510JH/+ (پاکێجی to-99-8). ئەم پێکھاتە ئەنالۆگە پینی چوونەژوورەوە، دەرچوون و دابینکردنی وزەی ھەیە. سەرنج بدە بە داتاشیتی بەرھەمھێنەر بۆ ڕێکخستنەکانی پینی لادانی ئۆفسێت، قەرەبووکردنەوە و چالاککردن. گونجاوە بۆ ڕێکخستنی ئیشارەت و خولەکانی بەرزکەرەوە.
هیچ داتای وردی پینئاوت بەردەست نییە بۆ AD510JH/+.
سەرنج بدە بە داتاشیت بۆ ڕێکخستنی تەواوی پینەکان.
بەکارهێنانە باوەکان
AD510JH/+ گونجاوە بۆ 6 بەکارھێنانs: Precision Sensor Signal Conditioning, Strain-Gauge Bridge Instrumentation, Laboratory Measurement Instruments, Process-Control Loop Amplification, Current-to-Voltage Conversion, Legacy Test and Measurement Equipment.
Precision Sensor Signal Conditioning
The AD510JH/+ suits low-level sensor conditioning because its 100 uV maximum input offset and 25 nA maximum input bias current limit errors in high-impedance sources. Its 10 nV/sqrt(Hz) input-noise density at 1 kHz also supports careful extraction of small signals. Place it in a non-inverting or differential stage with matched feedback resistors, and calculate the bias-current error against the actual sensor impedance before finalizing the gain.
پێشنیارکراو
Strain-Gauge Bridge Instrumentation
A strain-gauge bridge produces a small differential signal that the AD510JH/+ can amplify with its 94 dB open-loop gain and built-in compensation. The device's 25 nA maximum bias current is particularly relevant when the bridge impedance is high, while its 3 uV/C offset drift contributes directly to span error. Match the amplifier inputs and feedback network carefully, and include input-bias and thermal-drift errors in the instrument calibration budget.
پێشنیارکراو
Laboratory Measurement Instruments
The AD510JH/+ is appropriate for laboratory instruments that amplify small voltages around a system reference, including source-measurement and calibration interfaces. Its 100 V/us slew rate preserves moderately fast signal transitions, while internally compensated operation simplifies the implementation of standard closed-loop amplifiers. Use the TO-99-8 construction when maintaining vintage instrument designs, and route supply bypassing close to the device to limit noise pickup.
پێشنیارکراو
Process-Control Loop Amplification
The AD510JH/+ can amplify a low-level error signal in legacy process-control equipment where the loop requires high open-loop gain and controlled offset. Its 94 dB open-loop gain supports accurate feedback performance, and the 100 V/us slew rate allows satisfactory response to many slow control signals. Verify the sensor output range against the amplifier's input common-mode limits and the actuator demand against its output-swing capability.
پێشنیارکراو
Current-to-Voltage Conversion
The AD510JH/+ is useful in transimpedance stages for photodiode, optical-power, or electrochemical sensors because low bias current reduces current-conversion error. Its 100 uV maximum offset establishes a meaningful limit for small output voltages, while the 94 dB open-loop gain improves loop control in the inverting configuration. Add the required feedback compensation capacitance and check stability at the intended gain before increasing the transimpedance value.
پێشنیارکراو
Legacy Test and Measurement Equipment
The TO-99-8 AD510JH/+ is well suited to repair and modernization of older test equipment that used hermetically sealed precision analog packages. Its 100 V/us slew rate, 94 dB open-loop gain, and 0 C to +70 C commercial range align with many laboratory and industrial instruments. Maintain the original 8-lead metal-can footprint or redesign explicitly, and validate offset, bias current, noise, and supply behavior against the original circuit.
پێشنیارکراو
کورتەی بەرهەمە پێشنیارکراوەکان
داتای سەرچاوەی ئەندازیاری بۆ AD510JH/+ — بەراوردکردن، ڕێنمایی دیزاین و زانیاری پابەندبوون.
ڕێنمایی هەڵبژاردن
بەراوردکردن لەگەڵ جێگرەوەکان
| پارامەتر | ئەم بەرهەمە | AD510JH | OP-27CJ | MXL1001ACH |
|---|---|---|---|---|
| Package | TO-99-8 | TO-99-8 | TO-99-8 | TO-99-8 |
| Brand | Analog Devices | Analog Devices | Analog Devices | Maxim Integrated |
جیاکەرەوە سەرەکییەکان
- Closest documented ordering alternative (بەراورد بەAD510JH)
- Higher documented open-loop gain than generic comparison candidates (بەراورد بەOP-27CJ)
- Defined noise and thermal-drift values for precision error budgeting (بەراورد بەMXL1001ACH)
تێبینییەکانی دیزاین
Design the supply rails so the AD510JH/+ retains adequate input common-mode range and output-swing margin at every operating point. The device has a bipolar input architecture and is characterized at approximately 4 mA supply current. Place supply-bypass capacitors close to the device leads and use separate return paths for input and output to reduce supply-induced offset and noise pickup.
Do not treat the TO-99-8 metal-can package as interchangeable with an SOIC or DIP footprint solely because both are eight-pin devices. Check lead spacing, body diameter, pin numbering, and the manufacturer pin-description table. The AD510JH ordering form is the closest documented match, while OP-27CJ and MXL1001ACH still require verification of pin mapping, bias current, compensation, and supply behavior.
For high-impedance sensor inputs, calculate the bias-current contribution using the source impedance and compare it with the AD510JH/+ specification of 25 nA maximum input bias current. Keep sensitive input traces short, guard high-impedance nodes where practical, and use matched feedback resistors. Include the specified 3 uV/C offset drift and 100 uV maximum offset in the total measurement-error budget.
Route the inverting and non-inverting connections away from supply pins and high-current output paths. Use a compact ground reference beneath the analog section and connect bypass-capacitor returns directly to the device ground pins. Since this is a leaded hermetically sealed package, also account for insertion stress and provide adequate clearance from tall adjacent components during legacy-board assembly and maintenance.
زانیاری پابەندبوون
The TO-99-8 hermetically sealed package predates current surface-mount lead-free practices. No explicit RoHS, REACH, halogen-free, or conflict-minerals declarations were identified, so these fields remain unknown.