AD600JNZ - Dual 35MHz Variable Gain Amplifier | Analog Devices
MPN: AD600JNZ ✓ Hoạt độngAD600JNZ Tóm tắt
A variable gain amplifier is a feedback-controlled amplifier whose gain can be adjusted by an external control voltage. In the AD600, the gain-control mechanism allows a signal chain to cover a wide dynamic range without changing the physical input or output routing. The device belongs to the special-purpose amplifier category, rather than the general-purpose operational-amplifier category, because its gain-control interface and wideband performance are optimized for demanding instrumentation and medical-imaging systems.
Key specifications include two independent amplifier channels, a nominal 35 MHz bandwidth that is essentially independent of gain, and a maximum gain of 41.07 dB. The dual ±5.25 V supply arrangement supports bipolar signal handling in systems where signal amplitude and common-mode range exceed the capabilities of a single-supply amplifier. The gating control input is compatible with TTL and CMOS logic, simplifying control from digital systems.
The AD600 uses a voltage-controlled gain architecture intended for precise signal-chain amplification. Its wideband behavior makes it suitable for systems that need bandwidth while varying gain, including ultrasound receiver channels, medical diagnostic instrumentation, test and measurement equipment, and communication or imaging modules. The manufacturer identifies the AD600 family as optimized for ultrasound imaging, while also noting applicability to any system requiring precise gain, low noise, low distortion, and wide bandwidth.
Designers should pay particular attention to supply decoupling, control-input logic levels, input and output impedance, and the bandwidth required for the selected gain setting. The 16-pin PDIP package is suitable for through-hole prototyping and industrial equipment where a surface-mount package is unnecessary. Because the device is a high-speed variable gain amplifier, PCB trace lengths, grounding, and power-supply return paths should be kept short and symmetrical.
This page summarizes the product identity, verified electrical attributes, package information, drop-in replacement candidates, and engineering considerations for the AD600JNZ. The alternatives are limited to same-brand family members where pin compatibility and parameter proximity can be assessed; engineers should confirm the exact control, supply, and timing requirements against the manufacturer datasheet before substituting a part.
Bộ thay thế dễ dàng lắp đặt cho AD600JNZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD600JNZ (cùng hình factor và footprint) — khác nhau ở Number of Channels, Operating Temperature Range, Package, Signal Type.
AD600JN
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →AD602JNZ
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →AD6021JNZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD604JNZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD600JZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD600JNZ Tỷ lệ tối đa & tính chất điện
| Device Type | Dual variable gain amplifier |
| Number of Channels | 2 circuits |
| Điện áp cung cấp | ±5.25 V |
| Maximum Gain | 41.07 dB |
| -3 dB Bandwidth | 35 MHz nominal |
| Gain Control Input | TTL- and CMOS-compatible |
| Hộp | 16-pin PDIP |
| Kiểu lắp đặt | Through-hole |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| AD600 Family Application | Ultrasound imaging systems |
| Signal Type | Variable-gain analog signal |
| Architecture | Dual-channel voltage-controlled amplifier |
| Bandwidth Dependence | Essentially independent of gain |
| Control Interface | External gating control input |
| Manufacturer Product Family | AD600 dual low-noise wideband variable gain amplifiers |
Hướng dẫn cấu hình chân AD600JNZ 16-pin pdip
Cấu hình chân cho AD600JNZ (16-pin pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD600JNZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD600JNZ phù hợp cho 6 Áp dụngs: Ultrasound receiver front end, Medical diagnostic instrumentation, Wideband signal conditioning, Test and measurement front end, Industrial imaging systems, Communication signal chains.
Ultrasound receiver front end
The AD600JNZ fits dual-channel ultrasound receiver paths because it combines two variable-gain amplifier circuits, a nominal 35 MHz -3 dB bandwidth, and a maximum gain of 41.07 dB in a 16-pin PDIP package. Its TTL- and CMOS-compatible gating input can be driven by the acquisition system to vary gain as echo strength changes. Placing each channel near the receive transducer or front-end network helps control board-level noise and parasitic capacitance. Because the AD600 family is optimized for ultrasound imaging, this is the primary application supported by the manufacturer.
Được đề xuất
Medical diagnostic instrumentation
The AD600JNZ can form the variable-gain input stage of diagnostic equipment that captures low-amplitude sensor signals while requiring adjustable gain and wide bandwidth. Two channels allow simultaneous processing of related signals, and the 35 MHz nominal bandwidth supports fast acquisition stages. Dual ±5.25 V operation supports bipolar analog signals, while the external gating control simplifies digital adjustment. Medical designs must still complete their own risk, isolation, input-protection, and regulatory assessments for the finished system.
Được đề xuất
Wideband signal conditioning
The AD600JNZ is suitable for wideband signal-conditioning blocks that require programmable amplification rather than a fixed-gain operational amplifier. Its maximum gain of 41.07 dB provides substantial range for small sensor outputs, while the nominally 35 MHz bandwidth remains essentially independent of gain. The dual-channel configuration can condition two related inputs without duplicating the amplifier package. Designers should preserve controlled impedance paths and use short ground returns to prevent the wideband stage from amplifying board-level interference.
Được đề xuất
Test and measurement front end
The AD600JNZ can provide adjustable gain in instrumentation that sweeps signal amplitude while retaining a wide measurement bandwidth. The dual architecture is useful for differential, comparative, or sequential acquisition channels, and the TTL- and CMOS-compatible control input supports automated test-system sequencing. The nominal 35 MHz bandwidth and 41.07 dB maximum gain make the part appropriate for precision RF, IF, or high-speed pulse signals. Input and output protection should be selected to preserve the amplifier's operating limits.
Được đề xuất
Industrial imaging systems
The AD600JNZ can amplify variable-amplitude detector outputs in industrial imaging equipment that requires two synchronized channels and adjustable attenuation or gain. The dual ±5.25 V supply supports bipolar detector signals, while the 35 MHz nominal bandwidth accommodates fast sensor outputs. Its 16-pin PDIP package is practical for modular industrial control systems and prototype instrumentation. The system designer should calibrate the gain-control transfer characteristic and verify signal integrity at the highest required gain and bandwidth.
Được đề xuất
Communication signal chains
The AD600JNZ can serve as an adjustable analog gain element in communication equipment that must accommodate changing received-signal strength. Its two channels support matched receive paths, the control input accepts common digital signaling, and the wide nominal bandwidth supports high-frequency carrier-related signal processing. The maximum gain of 41.07 dB can reduce downstream receiver requirements when the front-end noise and distortion are acceptable. RF layout must follow controlled-impedance and grounding practices so that the wideband amplifier does not degrade channel symmetry.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD600JNZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD600JN | AD602JNZ | AD6021JNZ | AD604JNZ | AD600JZ |
|---|---|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Channels | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Product Type | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier |
Bảo phân biệt quan trọng
- Higher maximum gain within the related AD602 family (vsAD602JNZ)
- Closest functional and footprint match (vsAD600JN)
- Gain bandwidth remains essentially independent of gain (vsAD6021JNZ)
Ghi chú thiết kế
Keep the AD600JNZ supply, ground, input, output, and gain-control paths short and use a low-impedance ground plane. The device has nominal 35 MHz bandwidth, so long PCB traces, test-point capacitance, and switching-node proximity can affect signal integrity. Place input and output decoupling close to their respective pins, keep the two channels symmetrical when channel matching matters, and route high-speed signals away from digital control and power-converter nodes.
Provide clean dual ±5.25 V rails and verify the regulator and decoupling arrangement against the manufacturer's recommended schematic. The TTL- and CMOS-compatible gating input is convenient for digital control, but its return path should not pass through noisy or high-current switching regions. Establish power-up and power-down behavior for the control signal so that the gain-control node does not receive an uncontrolled transient during sequencing.
Do not treat any 16-pin PDIP AD600-family member as an automatic substitute without checking gain range, control polarity, supply limits, temperature grade, and calibration. In particular, the AD602 family is identified with a maximum gain of 31.07 dB versus 41.07 dB for the AD600, a 10 dB difference that can alter downstream gain planning. Use the manufacturer pinout and ordering guide to confirm the exact replacement.
Choose source and load impedances that support the intended gain-control setting and operating bandwidth, and terminate unused inputs and outputs as directed in the manufacturer data sheet. Because the AD600 bandwidth is essentially independent of gain, the highest-frequency signal path should be evaluated across the complete control range rather than only at maximum gain. Probe using short ground springs or controlled board structures to avoid adding unintended capacitance.
Thông tin tuân thủ
The verified product information does not provide explicit compliance declarations. AEC-Q100 is not applicable because AD600JNZ is an industrial/commercial dual variable gain amplifier rather than an automotive-qualified device.