AD600JNZ - Dual 35MHz Variable Gain Amplifier | Analog Devices
N.º de pieza: AD600JNZ ✓ ActivoAD600JNZ Descripción general
A variable gain amplifier is a feedback-controlled amplifier whose gain can be adjusted by an external control voltage. In the AD600, the gain-control mechanism allows a signal chain to cover a wide dynamic range without changing the physical input or output routing. The device belongs to the special-purpose amplifier category, rather than the general-purpose operational-amplifier category, because its gain-control interface and wideband performance are optimized for demanding instrumentation and medical-imaging systems.
Key specifications include two independent amplifier channels, a nominal 35 MHz bandwidth that is essentially independent of gain, and a maximum gain of 41.07 dB. The dual ±5.25 V supply arrangement supports bipolar signal handling in systems where signal amplitude and common-mode range exceed the capabilities of a single-supply amplifier. The gating control input is compatible with TTL and CMOS logic, simplifying control from digital systems.
The AD600 uses a voltage-controlled gain architecture intended for precise signal-chain amplification. Its wideband behavior makes it suitable for systems that need bandwidth while varying gain, including ultrasound receiver channels, medical diagnostic instrumentation, test and measurement equipment, and communication or imaging modules. The manufacturer identifies the AD600 family as optimized for ultrasound imaging, while also noting applicability to any system requiring precise gain, low noise, low distortion, and wide bandwidth.
Designers should pay particular attention to supply decoupling, control-input logic levels, input and output impedance, and the bandwidth required for the selected gain setting. The 16-pin PDIP package is suitable for through-hole prototyping and industrial equipment where a surface-mount package is unnecessary. Because the device is a high-speed variable gain amplifier, PCB trace lengths, grounding, and power-supply return paths should be kept short and symmetrical.
This page summarizes the product identity, verified electrical attributes, package information, drop-in replacement candidates, and engineering considerations for the AD600JNZ. The alternatives are limited to same-brand family members where pin compatibility and parameter proximity can be assessed; engineers should confirm the exact control, supply, and timing requirements against the manufacturer datasheet before substituting a part.
Alternativas directas para AD600JNZ — mismo encapsulado, compatible pin a pin. Se excluyen las piezas de otro encapsulado que requieren retrabajo de la PCB.
Variantes de esta serie
Modelos de la misma serie compatibles directamente con AD600JNZ (mismo factor de forma y huella) — difiere en Number of Channels, Operating Temperature Range, Package, Signal Type.
AD600JN
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →AD602JNZ
✅ Sustitución directa ⚠️ Especificaciones sin verificarConsulte el precio
Ver hoja de datos →AD6021JNZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD604JNZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD600JZ
✅ Sustitución directa ⚠️ Especificaciones sin verificar📋 Alternativa de referencia (no en el catálogo)
AD600JNZ Valores máximos y características eléctricas
| Device Type | Dual variable gain amplifier |
| Number of Channels | 2 circuits |
| Tensión de alimentación | ±5.25 V |
| Maximum Gain | 41.07 dB |
| -3 dB Bandwidth | 35 MHz nominal |
| Gain Control Input | TTL- and CMOS-compatible |
| Encapsulado | 16-pin PDIP |
| Tipo de montaje | Through-hole |
| Rango de temperatura de funcionamiento | -40 °C to +85 °C |
| AD600 Family Application | Ultrasound imaging systems |
| Signal Type | Variable-gain analog signal |
| Architecture | Dual-channel voltage-controlled amplifier |
| Bandwidth Dependence | Essentially independent of gain |
| Control Interface | External gating control input |
| Manufacturer Product Family | AD600 dual low-noise wideband variable gain amplifiers |
Guía de configuración de pines de AD600JNZ 16-pin pdip
Configuración de pines para AD600JNZ (encapsulado 16-pin pdip). Este componente analógico presenta pines de entrada, salida y alimentación. Consulte la hoja de datos del fabricante para conocer las configuraciones de los pines de ajuste de offset, compensación y habilitación. Ideal para circuitos de acondicionamiento de señal y amplificadores.
No hay datos detallados de patillaje disponibles para AD600JNZ.
Consulte la hoja de datos para ver la configuración completa de patillas.
Aplicaciones típicas
AD600JNZ es adecuado para 6 aplicacións: Ultrasound receiver front end, Medical diagnostic instrumentation, Wideband signal conditioning, Test and measurement front end, Industrial imaging systems, Communication signal chains.
Ultrasound receiver front end
The AD600JNZ fits dual-channel ultrasound receiver paths because it combines two variable-gain amplifier circuits, a nominal 35 MHz -3 dB bandwidth, and a maximum gain of 41.07 dB in a 16-pin PDIP package. Its TTL- and CMOS-compatible gating input can be driven by the acquisition system to vary gain as echo strength changes. Placing each channel near the receive transducer or front-end network helps control board-level noise and parasitic capacitance. Because the AD600 family is optimized for ultrasound imaging, this is the primary application supported by the manufacturer.
Recomendado
Medical diagnostic instrumentation
The AD600JNZ can form the variable-gain input stage of diagnostic equipment that captures low-amplitude sensor signals while requiring adjustable gain and wide bandwidth. Two channels allow simultaneous processing of related signals, and the 35 MHz nominal bandwidth supports fast acquisition stages. Dual ±5.25 V operation supports bipolar analog signals, while the external gating control simplifies digital adjustment. Medical designs must still complete their own risk, isolation, input-protection, and regulatory assessments for the finished system.
Recomendado
Wideband signal conditioning
The AD600JNZ is suitable for wideband signal-conditioning blocks that require programmable amplification rather than a fixed-gain operational amplifier. Its maximum gain of 41.07 dB provides substantial range for small sensor outputs, while the nominally 35 MHz bandwidth remains essentially independent of gain. The dual-channel configuration can condition two related inputs without duplicating the amplifier package. Designers should preserve controlled impedance paths and use short ground returns to prevent the wideband stage from amplifying board-level interference.
Recomendado
Test and measurement front end
The AD600JNZ can provide adjustable gain in instrumentation that sweeps signal amplitude while retaining a wide measurement bandwidth. The dual architecture is useful for differential, comparative, or sequential acquisition channels, and the TTL- and CMOS-compatible control input supports automated test-system sequencing. The nominal 35 MHz bandwidth and 41.07 dB maximum gain make the part appropriate for precision RF, IF, or high-speed pulse signals. Input and output protection should be selected to preserve the amplifier's operating limits.
Recomendado
Industrial imaging systems
The AD600JNZ can amplify variable-amplitude detector outputs in industrial imaging equipment that requires two synchronized channels and adjustable attenuation or gain. The dual ±5.25 V supply supports bipolar detector signals, while the 35 MHz nominal bandwidth accommodates fast sensor outputs. Its 16-pin PDIP package is practical for modular industrial control systems and prototype instrumentation. The system designer should calibrate the gain-control transfer characteristic and verify signal integrity at the highest required gain and bandwidth.
Recomendado
Communication signal chains
The AD600JNZ can serve as an adjustable analog gain element in communication equipment that must accommodate changing received-signal strength. Its two channels support matched receive paths, the control input accepts common digital signaling, and the wide nominal bandwidth supports high-frequency carrier-related signal processing. The maximum gain of 41.07 dB can reduce downstream receiver requirements when the front-end noise and distortion are acceptable. RF layout must follow controlled-impedance and grounding practices so that the wideband amplifier does not degrade channel symmetry.
Recomendado
Resumen de productos recomendados
Datos de referencia de ingeniería para AD600JNZ — comparación, orientación de diseño e información de cumplimiento.
Guía de selección
Comparación con alternativas
| Parámetro | Este producto | AD600JN | AD602JNZ | AD6021JNZ | AD604JNZ | AD600JZ |
|---|---|---|---|---|---|---|
| Package | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP | 16-pin PDIP |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Number of Channels | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits | 2 circuits |
| Product Type | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier | Variable gain amplifier |
Diferenciadores clave
- Higher maximum gain within the related AD602 family (frente a AD602JNZ)
- Closest functional and footprint match (frente a AD600JN)
- Gain bandwidth remains essentially independent of gain (frente a AD6021JNZ)
Notas de diseño
Keep the AD600JNZ supply, ground, input, output, and gain-control paths short and use a low-impedance ground plane. The device has nominal 35 MHz bandwidth, so long PCB traces, test-point capacitance, and switching-node proximity can affect signal integrity. Place input and output decoupling close to their respective pins, keep the two channels symmetrical when channel matching matters, and route high-speed signals away from digital control and power-converter nodes.
Provide clean dual ±5.25 V rails and verify the regulator and decoupling arrangement against the manufacturer's recommended schematic. The TTL- and CMOS-compatible gating input is convenient for digital control, but its return path should not pass through noisy or high-current switching regions. Establish power-up and power-down behavior for the control signal so that the gain-control node does not receive an uncontrolled transient during sequencing.
Do not treat any 16-pin PDIP AD600-family member as an automatic substitute without checking gain range, control polarity, supply limits, temperature grade, and calibration. In particular, the AD602 family is identified with a maximum gain of 31.07 dB versus 41.07 dB for the AD600, a 10 dB difference that can alter downstream gain planning. Use the manufacturer pinout and ordering guide to confirm the exact replacement.
Choose source and load impedances that support the intended gain-control setting and operating bandwidth, and terminate unused inputs and outputs as directed in the manufacturer data sheet. Because the AD600 bandwidth is essentially independent of gain, the highest-frequency signal path should be evaluated across the complete control range rather than only at maximum gain. Probe using short ground springs or controlled board structures to avoid adding unintended capacitance.
Información de cumplimiento
The verified product information does not provide explicit compliance declarations. AEC-Q100 is not applicable because AD600JNZ is an industrial/commercial dual variable gain amplifier rather than an automotive-qualified device.