AD629BN - ±270V High Common-Mode Difference Amplifier | Analog Devices
MPN: AD629BN ✓ Hoạt độngAD629BN Tóm tắt
A difference amplifier is a specialized amplifier IC that amplifies the voltage difference between two inputs while rejecting a voltage common to both inputs. This category sits within amplifier ICs and instrumentation signal-chain devices. It is particularly useful when a sensor, shunt, transducer, or measurement node operates at a high DC voltage but the useful information is represented by a comparatively small differential signal.
The AD629BN provides a differential gain of unity. To achieve its high common-mode range, an internal resistor divider attenuates the noninverting input by a factor of 20. Other internal resistors, including the feedback network, restore the overall differential gain to unity. This architecture allows accurate differential measurement without changing the nominal system gain.
The manufacturer identifies the AD629 as a production device and describes it as a precision device for measuring differential signals in the presence of common-mode voltages up to ±270 V. Its integrated resistor network simplifies the external circuit compared with a discrete difference-amplifier implementation. The eight-pin PDIP package also supports conventional through-hole assembly and prototype rework.
Typical uses include power-converter feedback monitoring, motor-drive bus measurement, industrial control sensing, battery-system instrumentation, and high-voltage test equipment. In these applications, the AD629BN can reject the large common-mode voltage while preserving a differential voltage measurement suitable for an ADC, comparator, control loop, or diagnostic circuit.
A key design consideration is that the input common-mode voltage must remain within the device's specified operating range under all transient and fault conditions. Designers should also verify the allowed differential input range, supply requirements, output swing, bandwidth, and gain error against their exact operating conditions using the manufacturer datasheet before finalizing the circuit.
This product page combines the AD629 architecture, operating-range details, package information, replacement guidance, and application-focused design notes to support faster component selection, PCB planning, and precision signal-chain design.
Bộ thay thế dễ dàng lắp đặt cho AD629BN — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD629BN (cùng hình factor và footprint) — khác nhau ở Common-Mode Input Voltage Range, Mounting Type, Package.
AD629BNZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD629ANZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
INA117P
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →AD629BN Tỷ lệ tối đa & tính chất điện
| Product Type | Precision difference amplifier |
| Common-Mode Input Voltage Range | ±270 V |
| Differential Gain | 1 V/V (unity gain) |
| Internal Noninverting Attenuation Ratio | 20:1 |
| Số lượng chân | 8 pins |
| Hộp | PDIP-8 |
| Kiểu lắp đặt | Through-hole |
| Device Type | Single amplifier |
Hướng dẫn cấu hình chân AD629BN pdip-8
Cấu hình chân cho AD629BN (pdip-8 gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD629BN.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD629BN phù hợp cho 6 Áp dụngs: High-Voltage Industrial Sensor Interface, Power-Converter Feedback Monitoring, Motor-Drive DC-Bus Measurement, Battery-Pack Balance Monitoring, High-Voltage Test and Measurement, Precision Bridge and Shunt Readout.
High-Voltage Industrial Sensor Interface
The AD629BN fits measurement nodes where two sensing wires can sit at a common-mode potential as high as ±270 V while carrying a small differential signal. Its unity-gain difference-amplifier architecture rejects the shared voltage and presents the differential component to a controller or ADC. The integrated 20:1 noninverting attenuation and feedback network simplify the front end. Designers should verify transient limits, input protection, bandwidth, and downstream signal range at the highest expected bus voltage.
Được đề xuất
Power-Converter Feedback Monitoring
The AD629BN can monitor a small voltage difference across a converter shunt or sensing network even when the power stage operates at a high DC bus voltage. Its ±270 V common-mode range is useful for isolating the useful differential feedback signal from the switching-node potential, while unity gain keeps the nominal transfer straightforward. Validate converter transients, bandwidth requirements, output settling, and common-mode excursions before using the amplifier directly at the switching node.
Được đề xuất
Motor-Drive DC-Bus Measurement
The AD629BN is suitable for sensing a low-level differential signal in a motor-drive system where the high-voltage bus is common to multiple input nodes. The ±270 V common-mode capability allows the device to operate without external high-voltage attenuation when the measured node remains within its absolute limits. Use appropriate surge and transient protection, maintain signal ground integrity, and confirm that the amplifier's response bandwidth covers the required diagnostics and control-loop bandwidth.
Được đề xuất
Battery-Pack Balance Monitoring
The AD629BN can support differential monitoring of battery cells or packs when the cell stack imposes a high common-mode voltage on the measurement input. Its unity-gain behavior is useful when the system must preserve a small voltage difference for an ADC, comparator, or balancing controller. Check the exact differential input limit, supply arrangement, error over temperature, and protection strategy for series-cell systems rather than assuming the common-mode rating covers every transient condition.
Được đề xuất
High-Voltage Test and Measurement
The AD629BN provides a compact way to observe small differential signals in high-voltage test fixtures where both input nodes can share a large voltage relative to the measurement system. The unity-gain architecture and integrated resistor network can simplify instrumentation around shunt elements and sensor bridges. Confirm input protection, isolation requirements, common-mode accuracy, bandwidth, and output headroom in the complete fixture to avoid overloading the amplifier during switching or fault tests.
Được đề xuất
Precision Bridge and Shunt Readout
The AD629BN can read a bridge or shunt whose differential output is small but whose common-mode voltage is high. Unity gain preserves the scale of the differential measurement, while the internal resistor network provides a defined difference-amplifier function. For instrumentation-grade accuracy, verify the applicable grade, gain error, offset, input bias current, output swing, and temperature coefficient. Input filtering and protection should be designed to preserve accuracy without adding excessive loading or leakage.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD629BN — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD629BNZ | AD629ANZ | INA117P |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | PDIP-8 | PDIP-8 | PDIP-8 | PDIP-8 |
| Function | Precision difference amplifier | Precision difference amplifier | Precision difference amplifier | Precision unity-gain difference amplifier |
| Differential Gain | 1 V/V (unity gain) | 1 V/V (unity gain) | 1 V/V (unity gain) | 1 V/V (unity gain) |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins |
| Mounting Style | Through-hole | Through-hole | Through-hole | Through-hole |
Bảo phân biệt quan trọng
- Very high common-mode measurement range (vsINA117P)
- Integrated difference-amplifier resistor network (vsINA117P)
- Closest same-family ordering option (vsAD629ANZ)
Ghi chú thiết kế
Do not treat the ±270 V common-mode rating as permission to exceed the separate differential input, absolute maximum, or supply-voltage limits. Review the AD629 manufacturer data sheet for every input and output constraint, then calculate worst-case conditions including startup, load dump, switching spikes, and fault states. Add input protection where the external system can exceed those limits, and ensure protection leakage does not degrade the intended measurement accuracy.
Keep the input, output, supply, and reference routing compact to minimize susceptibility to coupled noise in a high-voltage environment. Place input filtering and protection close to the amplifier pins, maintain a continuous return path, and avoid long parallel traces that can capacitively pick up switching-node energy. Confirm the pin functions in the manufacturer package drawing before assigning PCB nets, since the integrated resistor topology depends on exact pin connections.
Validate the complete signal path at the operating common-mode voltage and required measurement bandwidth. The internal divider attenuates the noninverting input by a factor of 20, while the feedback network restores unity differential gain, so parasitic capacitance, leakage, and ground movement can influence practical accuracy. Use short input routes, appropriate bypass capacitors, and an output path that keeps the amplifier within its specified operating region under startup and overload conditions.
Thông tin tuân thủ
The Analog Devices product page identifies AD629 as a production device but does not state RoHS, REACH, lead-free, halogen-free, or conflict-minerals status for AD629BN.