AD744SH - Fast-Settling FET Op Amp | Analog Devices
MPN: AD744SH ✗ Cuối đờiAD744SH Tóm tắt
An operational amplifier is an active semiconductor device that amplifies the voltage difference between its inverting and non-inverting inputs. A precision FET-input amplifier uses field-effect transistor input stages to provide very high input impedance and low input bias current. This places the AD744SH in the hierarchy of precision amplifiers, instrumentation amplifiers, analog signal-chain ICs, and semiconductor components.
The AD744 family’s principal characteristics include low input offset voltage, low bias current, and a 13 MHz gain-bandwidth product associated with the AD744SH/883B listing. Its precision input stage is useful when source impedance can create offset errors, while the fast-settling architecture supports applications requiring accurate signal recovery after a large input transition. The hermetic TO-99-8 package also supports applications where environmental robustness and stable operation are important.
Technically, the AD744 is a monolithic operational amplifier with a FET-input stage. Low bias current reduces the voltage error generated when input current flows through a high-value source resistance, while low offset voltage reduces the output error created by amplifier input mismatch. The 13 MHz bandwidth provides useful closed-loop bandwidth for low-frequency and moderate-frequency precision circuits when appropriate feedback and compensation networks are selected.
Typical uses include low-level signal conditioning, instrumentation front ends, active filters, transducers, laboratory measurement systems, and industrial control interfaces. The AD744SH is particularly appropriate where the input source has high impedance, the signal level is small, and measurement accuracy depends on minimizing both bias-current and offset-voltage errors.
Designers should begin with the manufacturer’s pin description and typical application circuits, then verify the external resistor, capacitor, and compensation selections against the required gain, bandwidth, and settling behavior. Pay particular attention to input common-mode range, supply voltage, output swing, and stability when driving capacitive loads; these requirements must be checked in the manufacturer datasheet before finalizing the circuit.
This page organizes the AD744SH product information with package guidance, source-linked technical data, application-focused engineering guidance, and a conservative drop-in-replacement assessment. It also distinguishes verified package and electrical characteristics from parameters that require confirmation in the manufacturer datasheet, helping engineers plan sourcing and design reviews more efficiently.
Bộ thay thế dễ dàng lắp đặt cho AD744SH — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếAD744SH Tỷ lệ tối đa & tính chất điện
| Product Type | 1-circuit operational amplifier |
| Input Stage | FET input |
| Gain-Bandwidth Product | 13 MHz |
| Input Offset Voltage | 300 uV |
| Input Bias Current | 30 pA |
| Hộp | TO-99-8 metal can |
| Số chân | 8 pins |
| Kiểu lắp đặt | Through-hole |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân AD744SH to-99-8 metal can
Cấu hình chân cho AD744SH (to-99-8 metal can gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD744SH.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD744SH phù hợp cho 6 Áp dụngs: High-Impedance Instrumentation, Precision Active Filtering, Transducer Signal Conditioning, Laboratory Measurement Systems, Industrial Sensor Interfaces, Low-Level Buffering.
High-Impedance Instrumentation
The AD744SH fits high-impedance instrumentation front ends because its FET input stage provides 30 pA input bias current and 300 uV input offset voltage. The low bias current limits the voltage error developed as input current flows through high-value sensor resistors, while the low offset reduces output error from input-stage mismatch. Its 13 MHz gain-bandwidth product also permits useful closed-loop bandwidth when the required noise gain remains appropriate. Use a guarded, low-leakage layout around the input pins and confirm the common-mode range in the manufacturer datasheet before selecting the supply voltage.
Được đề xuất
Precision Active Filtering
The AD744SH can serve in precision active-filter stages where low input current and adequate bandwidth are both important. The 30 pA input bias current reduces disturbance of high-impedance filter nodes, while the 13 MHz gain-bandwidth product supports closed-loop operation beyond the baseband in many measurement applications. Compensation resistors and capacitors should be selected using the Analog Devices recommended values for the required gain. Check noise gain, phase margin, and capacitive loading at the highest intended operating frequency rather than relying on gain-bandwidth product alone.
Được đề xuất
Transducer Signal Conditioning
The AD744SH is appropriate for conditioning signals from high-impedance transducers such as strain gauges, piezoelectric sensors, and chemical sensors. Its 30 pA input bias current minimizes the voltage error associated with leakage through the transducer and its bias network, while 300 uV input offset voltage supports accurate amplification of small differential signals. The fast-settling characteristic of the AD744 family helps the circuit recover after calibration or range changes. The signal bandwidth, input bias network, and allowable sensor polarity must be evaluated together to avoid forcing the amplifier outside its electrical limits.
Được đề xuất
Laboratory Measurement Systems
The AD744SH fits laboratory measurement systems that combine low-level source signals with relatively high source impedance. Its low 30 pA input bias current reduces loading errors, and the 13 MHz gain-bandwidth product supports amplification of signals beyond baseband when the closed-loop design is stable. The precision FET-input architecture also makes the device useful in buffer and difference-amplifier arrangements. Keep input wiring short, use clean grounding, and separate sensitive input routing from digital and switching circuitry to prevent errors that are not attributable to the amplifier itself.
Được đề xuất
Industrial Sensor Interfaces
The AD744SH can be used at the input side of industrial sensor interfaces when low bias current, low offset, and fast signal settling are required. The FET input reduces errors from high-impedance sensor sources, and the 300 uV offset specification is useful when small process or environmental signals must be retained. The 13 MHz gain-bandwidth product allows the amplifier to close a useful loop bandwidth at moderate gains. In industrial equipment, verify operation temperature, supply range, isolation boundaries, and surge requirements in the manufacturer documentation before final release.
Được đề xuất
Low-Level Buffering
The AD744SH is effective as a low-level unity-gain buffer when the source has high impedance and output settling must follow input transitions quickly. In voltage-follower service, the 30 pA input bias current limits disturbance of the source, while the amplifier’s fast-settling behavior reduces acquisition time. A 13 MHz gain-bandwidth product leaves useful bandwidth for small-signal applications, but stability must be checked for the actual load and stray capacitance. Use a clean reference ground and ensure the buffered signal remains inside the device’s input and output ranges.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD744SH — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Ghi chú thiết kế
Keep the AD744SH input leads short and treat leakage around high-impedance nodes as part of the circuit design. With 30 pA input bias current, a 1 Gohm source resistance can produce an input-referred error of 30 mV, so board contamination, socket leakage, and guard-ring technique can materially affect accuracy. Follow the guarding and layout guidance in the Analog Devices AD744 documentation and use clean, low-leakage assembly practices.
Do not assume that every AD744 ordering code is board-compatible with the AD744SH. The family is offered in 8-pin plastic mini-DIP, small-outline, cerdip, and TO-99 packages. The AD744JRZ, for example, is an 8-pin SOIC and therefore does not share the AD744SH TO-99 land pattern. Before substitution, compare the mechanical drawing, lead dimensions, pin numbering, and each electrical limit rather than relying only on the base device name.
Route the sensitive input node as a short, guarded trace and place input-bias resistors directly beside the amplifier pins when practical. Keep the layout away from power-converter switches, clock lines, and high-impedance summing nodes. In high-gain or precision filtering applications, evaluate component tolerances and parasitic capacitance because the 13 MHz gain-bandwidth product can shift usable bandwidth, noise gain, and settling performance.
Thông tin tuân thủ
RoHS compliance is associated with the AD744SH/883B listing. Other environmental and material-compliance attributes are not established.