Analog Devices

AD744SH - Fast-Settling FET Op Amp | Analog Devices

料号: AD744SH ✗ 停产
300 uV Vdss 30 pA Id TO-99-8 metal can Package
最小起订量: 1 |

AD744SH 概述

The Analog Devices AD744SH is a precision, fast-settling, FET-input monolithic operational amplifier rated for 13 MHz gain-bandwidth performance, 300 uV input offset voltage, and 30 pA input bias current in an 8-pin TO-99 metal-can package. The AD744 family combines precision direct-current characteristics with enhanced settling behavior, slew rate, and bandwidth for high-impedance instrumentation and signal-conditioning systems.

An operational amplifier is an active semiconductor device that amplifies the voltage difference between its inverting and non-inverting inputs. A precision FET-input amplifier uses field-effect transistor input stages to provide very high input impedance and low input bias current. This places the AD744SH in the hierarchy of precision amplifiers, instrumentation amplifiers, analog signal-chain ICs, and semiconductor components.

The AD744 family’s principal characteristics include low input offset voltage, low bias current, and a 13 MHz gain-bandwidth product associated with the AD744SH/883B listing. Its precision input stage is useful when source impedance can create offset errors, while the fast-settling architecture supports applications requiring accurate signal recovery after a large input transition. The hermetic TO-99-8 package also supports applications where environmental robustness and stable operation are important.

Technically, the AD744 is a monolithic operational amplifier with a FET-input stage. Low bias current reduces the voltage error generated when input current flows through a high-value source resistance, while low offset voltage reduces the output error created by amplifier input mismatch. The 13 MHz bandwidth provides useful closed-loop bandwidth for low-frequency and moderate-frequency precision circuits when appropriate feedback and compensation networks are selected.

Typical uses include low-level signal conditioning, instrumentation front ends, active filters, transducers, laboratory measurement systems, and industrial control interfaces. The AD744SH is particularly appropriate where the input source has high impedance, the signal level is small, and measurement accuracy depends on minimizing both bias-current and offset-voltage errors.

Designers should begin with the manufacturer’s pin description and typical application circuits, then verify the external resistor, capacitor, and compensation selections against the required gain, bandwidth, and settling behavior. Pay particular attention to input common-mode range, supply voltage, output swing, and stability when driving capacitive loads; these requirements must be checked in the manufacturer datasheet before finalizing the circuit.

This page organizes the AD744SH product information with package guidance, source-linked technical data, application-focused engineering guidance, and a conservative drop-in-replacement assessment. It also distinguishes verified package and electrical characteristics from parameters that require confirmation in the manufacturer datasheet, helping engineers plan sourcing and design reviews more efficiently.

直接替换替代料: AD744SH ——相同封装,引脚兼容。需要 PCB 改动的不同封装料号已排除。

该产品暂无直接替换替代料。

请求替代料

AD744SH 最大额定值与电气特性

Product Type 1-circuit operational amplifier
Input Stage FET input
Gain-Bandwidth Product 13 MHz
Input Offset Voltage 300 uV
Input Bias Current 30 pA
封装 TO-99-8 metal can
引脚数量 8 pins
安装类型 Through-hole
RoHS 状态 Compliant

AD744SH to-99-8 metal can 引脚配置指南

AD744SH(to-99-8 metal can 封装)的引脚配置。 该模拟元件具有输入、输出和电源引脚。请参阅制造商数据手册以了解失调调零、补偿和使能引脚配置。适用于信号调理和放大器电路。

AD744SH 的 to-99-8 metal can 封装引脚图

暂无详细引脚数据: AD744SH.

请参阅 数据手册 以查看完整引脚配置。

典型应用

AD744SH 适用于 6 应用s: High-Impedance Instrumentation, Precision Active Filtering, Transducer Signal Conditioning, Laboratory Measurement Systems, Industrial Sensor Interfaces, Low-Level Buffering.

🏭

High-Impedance Instrumentation

The AD744SH fits high-impedance instrumentation front ends because its FET input stage provides 30 pA input bias current and 300 uV input offset voltage. The low bias current limits the voltage error developed as input current flows through high-value sensor resistors, while the low offset reduces output error from input-stage mismatch. Its 13 MHz gain-bandwidth product also permits useful closed-loop bandwidth when the required noise gain remains appropriate. Use a guarded, low-leakage layout around the input pins and confirm the common-mode range in the manufacturer datasheet before selecting the supply voltage.

🌐

Precision Active Filtering

The AD744SH can serve in precision active-filter stages where low input current and adequate bandwidth are both important. The 30 pA input bias current reduces disturbance of high-impedance filter nodes, while the 13 MHz gain-bandwidth product supports closed-loop operation beyond the baseband in many measurement applications. Compensation resistors and capacitors should be selected using the Analog Devices recommended values for the required gain. Check noise gain, phase margin, and capacitive loading at the highest intended operating frequency rather than relying on gain-bandwidth product alone.

💊

Transducer Signal Conditioning

The AD744SH is appropriate for conditioning signals from high-impedance transducers such as strain gauges, piezoelectric sensors, and chemical sensors. Its 30 pA input bias current minimizes the voltage error associated with leakage through the transducer and its bias network, while 300 uV input offset voltage supports accurate amplification of small differential signals. The fast-settling characteristic of the AD744 family helps the circuit recover after calibration or range changes. The signal bandwidth, input bias network, and allowable sensor polarity must be evaluated together to avoid forcing the amplifier outside its electrical limits.

🧩

Laboratory Measurement Systems

The AD744SH fits laboratory measurement systems that combine low-level source signals with relatively high source impedance. Its low 30 pA input bias current reduces loading errors, and the 13 MHz gain-bandwidth product supports amplification of signals beyond baseband when the closed-loop design is stable. The precision FET-input architecture also makes the device useful in buffer and difference-amplifier arrangements. Keep input wiring short, use clean grounding, and separate sensitive input routing from digital and switching circuitry to prevent errors that are not attributable to the amplifier itself.

⚡

Industrial Sensor Interfaces

The AD744SH can be used at the input side of industrial sensor interfaces when low bias current, low offset, and fast signal settling are required. The FET input reduces errors from high-impedance sensor sources, and the 300 uV offset specification is useful when small process or environmental signals must be retained. The 13 MHz gain-bandwidth product allows the amplifier to close a useful loop bandwidth at moderate gains. In industrial equipment, verify operation temperature, supply range, isolation boundaries, and surge requirements in the manufacturer documentation before final release.

🔧

Low-Level Buffering

The AD744SH is effective as a low-level unity-gain buffer when the source has high impedance and output settling must follow input transitions quickly. In voltage-follower service, the 30 pA input bias current limits disturbance of the source, while the amplifier’s fast-settling behavior reduces acquisition time. A 13 MHz gain-bandwidth product leaves useful bandwidth for small-signal applications, but stability must be checked for the actual load and stray capacitance. Use a clean reference ground and ensure the buffered signal remains inside the device’s input and output ranges.

What is the AD744SH?
The AD744SH is a precision, fast-settling, FET-input monolithic operational amplifier from Analog Devices. The device is associated with a 13 MHz gain-bandwidth product, 300 uV input offset voltage, and 30 pA input bias current. According to the Analog Devices AD744 product information, it combines the direct-current characteristics of the AD711 BiFET family with improved settling behavior, slew rate, and bandwidth for precision signal-conditioning applications.
Where can I download the AD744SH datasheet PDF?
The official AD744SH family documentation is available through the Analog Devices AD744 product page at https://www.analog.com/en/products/ad744.html. The manufacturer datasheet contains the authoritative pin descriptions, electrical characteristics, package outlines, ordering information, and typical application circuits. Use the AD744SH order code when checking package and screening details, and confirm the operating limits against the specific revision of the manufacturer documentation.
What are the key specifications of AD744SH that engineers should know?
The AD744SH is a single monolithic operational amplifier with a FET input stage, 13 MHz gain-bandwidth product, 300 uV input offset voltage, and 30 pA input bias current. It is associated with the 8-pin TO-99-8 metal-can package. Analog Devices describes the AD744 as a fast-settling precision amplifier that enhances the settling, slew-rate, and bandwidth characteristics of the AD711 BiFET family while retaining low-error input behavior.
Why is the 30 pA input bias current of AD744SH important?
The 30 pA input bias current makes the AD744SH suitable for signals sourced from high-impedance sensors because current flowing through a high source resistance creates an input-referred voltage error. The resulting error is approximately the bias current multiplied by the effective source resistance. The manufacturer’s AD744 product information identifies the AD744 as a precision FET-input amplifier, making its low-current input stage useful for strain gauges, photodetectors, chemical sensors, and laboratory instrumentation.
Is AD744SH suitable for high-impedance sensor front ends?
Yes, the AD744SH is suited to high-impedance sensor front ends because its FET input stage provides 30 pA input bias current and 300 uV input offset voltage. These characteristics reduce errors from leakage through high-value source resistors and from amplifier input mismatch. The exact usable common-mode range and input network must still be checked in the manufacturer datasheet because those limits depend on the supply configuration.
What is AD744SH vs AD711 and which is better for fast settling?
The AD744SH is the better choice when fast settling is more important than using the original AD711 architecture. According to the Analog Devices product information, the AD744 retains the excellent direct-current characteristics associated with the AD711 BiFET family while adding enhanced settling, slew rate, and bandwidth. A design that already meets its accuracy requirements with an AD711 may still benefit from the AD744 when transition recovery or acquisition time dominates performance.
When should I choose AD744SH instead of a general-purpose precision amplifier?
Choose the AD744SH when the signal source has appreciable impedance, low input bias current is important, and the amplifier must recover quickly after a signal transition. Its 30 pA input bias current, 300 uV input offset voltage, and 13 MHz gain-bandwidth product provide a clear combination of precision and speed. A general-purpose amplifier may be adequate when source impedance is low and settling requirements are relaxed, but the AD744SH adds more targeted performance for precision front ends.
Is AD744SH suitable for active filters and precision signal conditioning?
The AD744SH is suitable for active filters and precision signal-conditioning circuits because it combines a 13 MHz gain-bandwidth product with low input bias current and low offset voltage. The high bandwidth provides closed-loop capability beyond the audio range when the loop gain and noise-gain requirements permit it. Component tolerances and the amplifier’s stability behavior must be considered at the selected gain, especially when the filter presents reactive loads.
What can replace AD744SH?
No confirmed pin-to-pin drop-in replacement for the AD744SH is established by the available manufacturer and cross-reference information. The AD744 family is offered in several packages, including 8-pin plastic mini-DIP, small-outline, cerdip, and TO-99 forms, so an AD744-family ordering code may use a different footprint. A replacement should therefore be accepted only after its exact package, pin assignments, electrical limits, screening level, and mounting configuration have been compared with the AD744SH.
What is the best cross-brand equivalent for AD744SH?
A specific cross-brand drop-in equivalent for the AD744SH cannot be recommended without an exact pinout and parametric comparison. Cross-reference search results indicate that the AD744 has numerous functional or possible analogues, but those categories do not prove that a candidate has the same TO-99-8 pin assignments or preserves the 300 uV offset and 30 pA bias-current requirements. Request a quotation through the Request a Quote form on this page, and request a manufacturer-approved migration recommendation when qualification risk must be minimized.
Can AD744JRZ replace AD744SH on the same PCB?
No, the AD744JRZ should not be treated as a direct board-level replacement for the AD744SH. The AD744JRZ is identified in the ordering information as an 8-pin SOIC, whereas the AD744SH is associated with the 8-pin TO-99 metal-can package. The different lead geometry and package outline require different PCB pads, so this is not a pin-to-pin drop-in substitution.
Where can I buy AD744SH online?
Use the Request a Quote form on this page to request the current AD744SH quotation, availability, lot traceability, and delivery schedule. Because this is a legacy precision amplifier, stock, condition, screening, and package handling can vary by lot. The customer-facing quote process avoids presenting stale market figures and lets the supplier confirm the exact AD744SH order code and any inspection requirements before an order is placed.
What is the price of AD744SH?
The current commercial price for the AD744SH is obtained through the Request a Quote form on this page. Quote requests should specify the required quantity, package, screening level, acceptable date code, and traceability documents. Legacy amplifier pricing can vary significantly with quantity and condition, so a firm quotation is more useful than a generic market figure or an unrelated AD744 package listing.
What is the lead time for AD744SH?
The current lead time for AD744SH is confirmed through the Request a Quote form on this page. For a legacy TO-99 precision amplifier, lead time can depend on available inventory, manufacturer lot status, inspection, and whether the order requires a specific date code or screening level. Provide the required quantity and traceability criteria with the request so the supplier can confirm the most accurate delivery commitment.
Is AD744SH in stock?
Current AD744SH inventory is checked when a customer submits the Request a Quote form on this page. Because the AD744SH is a legacy orderable device, stock may consist of different lots, screening conditions, or date codes. The quotation response should confirm the exact manufacturer part number, package, quantity, inspection status, and estimated delivery rather than treating every AD744-family listing as interchangeable.
How should I design the AD744SH input and feedback network?
Begin with the typical circuits in the Analog Devices AD744 datasheet and use low-leakage resistors or capacitors when source impedance is high. Keep the summing-node connections short, place sensitive input traces away from switching nodes, and verify stability with the intended gain, load, and cable capacitance. The 30 pA input bias current makes leakage control important, while the 13 MHz gain-bandwidth product requires attention to closed-loop bandwidth and noise gain.

工程参考数据: AD744SH ——对比、设计指导和合规信息。

选型指南

Choose the AD744SH when the design needs a precision FET-input operational amplifier with 30 pA input bias current, 300 uV input offset voltage, fast settling, and the 13 MHz gain-bandwidth product associated with the device. It is especially appropriate for high-impedance instrumentation, low-level transducer interfaces, precision filters, and laboratory measurement circuits. The TO-99-8 metal-can package is suitable when a legacy through-hole mechanical format is required. The AD744JRZ is not a drop-in choice for an existing AD744SH board because it uses an 8-pin SOIC package. No verified pin-to-pin replacement is identified, so alternate-family or cross-brand devices should enter the design only after their package, pinout, electrical limits, common-mode range, stability, and screening requirements are reviewed. For new TO-99 designs, request the manufacturer’s current lifecycle and documentation status before committing to production quantities.

设计说明

Keep the AD744SH input leads short and treat leakage around high-impedance nodes as part of the circuit design. With 30 pA input bias current, a 1 Gohm source resistance can produce an input-referred error of 30 mV, so board contamination, socket leakage, and guard-ring technique can materially affect accuracy. Follow the guarding and layout guidance in the Analog Devices AD744 documentation and use clean, low-leakage assembly practices.

Do not assume that every AD744 ordering code is board-compatible with the AD744SH. The family is offered in 8-pin plastic mini-DIP, small-outline, cerdip, and TO-99 packages. The AD744JRZ, for example, is an 8-pin SOIC and therefore does not share the AD744SH TO-99 land pattern. Before substitution, compare the mechanical drawing, lead dimensions, pin numbering, and each electrical limit rather than relying only on the base device name.

Route the sensitive input node as a short, guarded trace and place input-bias resistors directly beside the amplifier pins when practical. Keep the layout away from power-converter switches, clock lines, and high-impedance summing nodes. In high-gain or precision filtering applications, evaluate component tolerances and parasitic capacitance because the 13 MHz gain-bandwidth product can shift usable bandwidth, noise gain, and settling performance.

合规信息

RoHS
Compliant
REACH
Unknown
AEC-Q100
Not Applicable
无铅
Unknown
无卤
Unknown
冲突矿物
Unknown

RoHS compliance is associated with the AD744SH/883B listing. Other environmental and material-compliance attributes are not established.

相关搜索

ad744 datasheet AD744SH datasheet AD744SH datasheet pdf AD744SH pinout AD744SH equivalent AD744SH replacement AD744SH cross reference AD744SH TO-99-8 AD744SH 13 MHz AD744SH 30 pA AD744SH price AD744SH stock Analog Devices AD744SH AD744SH high impedance amplifier AD744SH vs AD711

相关元器件 & 术语

Analog Devices AD744SH AD744 AD711 AD744JRZ AD744SH/883B AD7450BRM AD745JR-16 operational amplifier precision amplifier FET-input amplifier BiFET input stage monolithic amplifier analog signal-chain IC semiconductor TO-99-8 TO-99 metal can through-hole package 13 MHz gain-bandwidth product 300 uV input offset voltage 30 pA input bias current high-impedance instrumentation precision active filter transducer signal conditioning
快速报价
填写完整信息——我们的销售团队将在 24 小时内回复
料号 制造商 封装 QTY 目标价 小计
✓
报价已提交!

我们将在 24 小时内回复您的邮件

1
询价已提交
2
已收到报价
3
已下单
4
支付
5
已发货
6
已送达
查看询价详情