AD745JR-16 - 20MHz Low-Noise FET Op Amp | Analog Devices
MPN: AD745JR-16 ✓ Hoạt độngAD745JR-16 Tóm tắt
A JFET-input operational amplifier is an analog signal-conditioning IC whose input stage uses junction field-effect transistors. Within the broader hierarchy of amplifier ICs, it belongs to the precision-amplifier family and provides high input impedance, low distortion, and wide bandwidth for signals that require both noise performance and speed. This makes the AD745 suitable where a conventional CMOS amplifier may lack sufficient input impedance or a slower bipolar device may add excessive noise.
The AD745 is designed for precision signal acquisition, instrumentation, audio, and sensor-interface applications. Its 20 MHz gain-bandwidth product supports useful closed-loop bandwidth well beyond audio frequencies, while the 12.5 V/µs slew rate improves large-signal response. The manufacturer describes the device as an ultralow-noise, high-speed, FET-input amplifier, and the 16-pin SOIC option is available in industrial and military temperature grades depending on the order code.
The AD745J grade is specified for the industrial temperature range of -40°C to +85°C. Its input stage provides the low input current expected from a FET design while preserving the low voltage-noise behavior normally associated with bipolar input amplifiers. The AD745 family is available in several packages, including 8-pin plastic mini-DIP, 8-pin cerdip, 16-pin SOIC, and chip form, allowing selection according to assembly method and thermal requirements.
Typical uses include low-level sensor amplification, precision current measurement, audio and instrumentation signal chains, photodiode interfaces, and high-impedance buffer stages. In these applications, the combination of low noise, low input bias current, and 20 MHz bandwidth allows the amplifier to condition signals without imposing a severe bandwidth or loading penalty on the source.
For stable operation, follow the manufacturer's recommended input and output network, provide adequate supply bypassing close to the device, and verify output swing, input common-mode range, and stability across the intended gain and load conditions. The JR-16 order code identifies the 16-pin SOIC package; exact pin functions, noise density, input bias current, and offset limits should be confirmed in the AD745 datasheet before finalizing a design.
Bộ thay thế dễ dàng lắp đặt cho AD745JR-16 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với AD745JR-16 (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Slew Rate, Gain-Bandwidth Product, Mounting Type.
AD745KRZ-16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD745JRZ-16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD745AJR-16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD745BJR-16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD745CJR-16
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
AD745JR-16 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | Single JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 20 MHz |
| Slew Rate | 12.5 V/µs |
| Supply Voltage Range | ±4.8 V to ±18 V |
| Total Supply Voltage | 9.6 V to 36 V |
| Khoảng nhiệt độ hoạt động | -40°C to +85°C |
| Hộp | 16-pin SOIC |
| Kiểu lắp đặt | Surface mount |
| Military Processing | Available for AD745S to MIL-STD-883B, Rev. C |
Cấu hình chân AD745JR-16
| Chân 1 | NC — Not connected |
| Chân 2 | -INPUT — Inverting input |
| Chân 3 | +INPUT — Non-inverting input |
| Chân 4 | -VS — Negative supply voltage |
| Chân 5 | NC — Not connected |
| Chân 6 | OUTPUT — Operational amplifier output |
| Chân 7 | +VS — Positive supply voltage |
| Chân 8 | NC — Not connected |
| Chân 9 | NC — Not connected |
| Chân 10 | NC — Not connected |
| Chân 11 | NC — Not connected |
| Chân 12 | NC — Not connected |
| Chân 13 | NC — Not connected |
| Chân 14 | NC — Not connected |
| Chân 15 | NC — Not connected |
| Chân 16 | NC — Not connected |
Ứng dụng tiêu biểu
AD745JR-16 phù hợp cho 6 Áp dụngs: Precision Sensor Signal Conditioning, Audio and Instrumentation Amplification, Photodiode and High-Impedance Buffering, Current Measurement Front Ends, Industrial Data Acquisition, Test and Measurement Signal Conditioning.
Precision Sensor Signal Conditioning
The AD745JR-16 fits low-level sensor interfaces because its JFET input stage provides very low input current, reducing loading on high-impedance sources, while its 20 MHz gain-bandwidth product preserves signal bandwidth. Place it in a non-inverting or differential conditioning stage ahead of an ADC or measurement converter. Compared with a general-purpose CMOS amplifier, the documented ultralow-noise, high-speed architecture better preserves small signals, although the exact noise density, input bias current, and common-mode limits must be checked for the selected grade.
Được đề xuất
Audio and Instrumentation Amplification
The AD745JR-16 is appropriate for precision audio and instrumentation paths where low voltage noise and moderate-to-high bandwidth are required together. Its 20 MHz gain-bandwidth product exceeds the useful range of many audio-only amplifiers, while the 12.5 V/µs slew rate improves response to larger transient waveforms. Use it in a low-gain preamplifier or line-level conditioning stage, and verify output drive, output swing, and stability against the intended load.
Được đề xuất
Photodiode and High-Impedance Buffering
A photodiode or capacitive sensor benefits from the AD745JR-16's low-input-current JFET stage because the source otherwise presents a very high impedance. The amplifier can buffer the sensor before a downstream sampling or transimpedance stage without contributing substantial loading. The 20 MHz bandwidth permits faster settling than many precision-only amplifiers, but photodiode capacitance, cable length, noise gain, and input-bias-current error must be included in the complete stability and sensitivity analysis.
Được đề xuất
Current Measurement Front Ends
The AD745JR-16 can amplify the small voltage produced by a shunt or current-sense element when low input bias current is important. Its JFET architecture avoids the higher bias currents commonly encountered with bipolar-input precision amplifiers, helping preserve measurement accuracy at high source impedance. The 20 MHz bandwidth allows the signal path to accommodate higher-frequency current waveforms, although designers should account for shunt impedance, common-mode voltage, amplifier offset, and the required gain-bandwidth product.
Được đề xuất
Industrial Data Acquisition
The AD745JR-16 works as an analog front-end amplifier for industrial data-acquisition systems requiring low-noise amplification over a broader bandwidth than a conventional precision amplifier. Its -40°C to +85°C industrial temperature range supports controlled equipment, and the ±4.8 V to ±18 V supply capability accommodates conventional bipolar analog rails. Pair it with suitable input filtering and an ADC, then verify noise, settling time, input-range limits, and system calibration across the operating temperature range.
Được đề xuất
Test and Measurement Signal Conditioning
The AD745JR-16 can condition low-level signals in test and measurement equipment while preserving the wide bandwidth needed for diagnostics and waveform capture. Its 20 MHz gain-bandwidth product and 12.5 V/µs slew rate provide more dynamic range than a slow precision-only op amp. Use it ahead of a higher-bandwidth converter when the source impedance is high enough to make low input bias current important, and check settling, output loading, and noise performance for the required measurement bandwidth.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD745JR-16 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD745KRZ-16 | AD745JRZ-16 | AD745AJR-16 | AD745BJR-16 | AD745CJR-16 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Amplifier Type | Single JFET-input operational amplifier | Single JFET-input operational amplifier | Single JFET-input operational amplifier | AD745-family JFET-input operational amplifier | AD745-family JFET-input operational amplifier | AD745-family JFET-input operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Slew Rate | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs |
| Supply Voltage Range | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V |
Bảo phân biệt quan trọng
- Combines a JFET input stage with high speed (vsAD745KRZ-16)
- Maintains the same 16-pin SOIC footprint (vsAD745JRZ-16)
- Supports industrial-temperature operation (vsAD745S)
Ghi chú thiết kế
Do not treat every AD745 order code as automatically interchangeable. The JR-16 suffix identifies a specific 16-pin SOIC configuration, while J, K, A, B, C, S, and Z suffix combinations can represent different temperature, qualification, or finish options. Before approving a substitution, compare the exact pinout, supply range, electrical limits, operating temperature, and qualification requirements. The package being the same 16-pin SOIC establishes footprint compatibility, not complete functional equivalence.
For high-impedance sources, minimize PCB leakage and contamination around the input pins because even a low input-bias-current amplifier can be disturbed by board-surface leakage. Keep the input traces short, avoid routing near switching nodes and high-impedance output traces, and use guarding techniques where practical. Include cable and probe capacitance in the stability analysis because the AD745's 20 MHz bandwidth is substantially higher than the bandwidth of many low-noise precision amplifiers.
Use the manufacturer's recommended supply-decoupling arrangement with short, low-inductance connections between the supply pins and local capacitors. The AD745JR-16 supports ±4.8 V to ±18 V operation, so verify that every powered terminal remains within its allowable limits, including during startup and shutdown. Do not apply a positive supply directly to the negative supply pin; provide a common ground reference or use the appropriate dual-rail arrangement for the chosen circuit topology.
Reserve the 16-pin SOIC footprint exactly according to the manufacturer land pattern, including all no-connect pins, and observe the standard pin-1 orientation. Keep the output route away from the input to minimize parasitic feedback, particularly when using inverting configurations with high gain. A ground plane should provide a low-impedance return for supply and signal currents, while analog and high-current switching paths should remain spatially separated.
Thông tin tuân thủ
The AD745 family is not identified as an AEC-Q100 automotive product in the available documentation. The AD745S family option is available processed to MIL-STD-883B, Rev. C. Specific RoHS, REACH, lead-free, and halogen-free declarations for the exact order code require confirmation from the manufacturer.