AD745JR-16 - 20MHz Low-Noise FET Op Amp | Analog Devices
MPN: AD745JR-16 ✓ فعالAD745JR-16 نمای کلی
A JFET-input operational amplifier is an analog signal-conditioning IC whose input stage uses junction field-effect transistors. Within the broader hierarchy of amplifier ICs, it belongs to the precision-amplifier family and provides high input impedance, low distortion, and wide bandwidth for signals that require both noise performance and speed. This makes the AD745 suitable where a conventional CMOS amplifier may lack sufficient input impedance or a slower bipolar device may add excessive noise.
The AD745 is designed for precision signal acquisition, instrumentation, audio, and sensor-interface applications. Its 20 MHz gain-bandwidth product supports useful closed-loop bandwidth well beyond audio frequencies, while the 12.5 V/µs slew rate improves large-signal response. The manufacturer describes the device as an ultralow-noise, high-speed, FET-input amplifier, and the 16-pin SOIC option is available in industrial and military temperature grades depending on the order code.
The AD745J grade is specified for the industrial temperature range of -40°C to +85°C. Its input stage provides the low input current expected from a FET design while preserving the low voltage-noise behavior normally associated with bipolar input amplifiers. The AD745 family is available in several packages, including 8-pin plastic mini-DIP, 8-pin cerdip, 16-pin SOIC, and chip form, allowing selection according to assembly method and thermal requirements.
Typical uses include low-level sensor amplification, precision current measurement, audio and instrumentation signal chains, photodiode interfaces, and high-impedance buffer stages. In these applications, the combination of low noise, low input bias current, and 20 MHz bandwidth allows the amplifier to condition signals without imposing a severe bandwidth or loading penalty on the source.
For stable operation, follow the manufacturer's recommended input and output network, provide adequate supply bypassing close to the device, and verify output swing, input common-mode range, and stability across the intended gain and load conditions. The JR-16 order code identifies the 16-pin SOIC package; exact pin functions, noise density, input bias current, and offset limits should be confirmed in the AD745 datasheet before finalizing a design.
جایگزینهای drop-in برای AD745JR-16 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای AD745JR-16 (همان فرمفاکتور و فوتپرینت) — متفاوت در Amplifier Type, Package, Slew Rate, Gain-Bandwidth Product, Mounting Type.
AD745KRZ-16
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD745JRZ-16
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD745AJR-16
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD745BJR-16
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD745CJR-16
✅ جایگزین مستقیم📋 جایگزین مرجع (خارج از کاتالوگ)
AD745JR-16 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Amplifier Type | Single JFET-input operational amplifier |
| Number of Circuits | 1 circuit |
| Gain-Bandwidth Product | 20 MHz |
| Slew Rate | 12.5 V/µs |
| Supply Voltage Range | ±4.8 V to ±18 V |
| Total Supply Voltage | 9.6 V to 36 V |
| محدوده دمای کاری | -40°C to +85°C |
| بستهبندی | 16-pin SOIC |
| نوع نصب | Surface mount |
| Military Processing | Available for AD745S to MIL-STD-883B, Rev. C |
پیکربندی پین AD745JR-16
| پین 1 | NC — Not connected |
| پین 2 | -INPUT — Inverting input |
| پین 3 | +INPUT — Non-inverting input |
| پین 4 | -VS — Negative supply voltage |
| پین 5 | NC — Not connected |
| پین 6 | OUTPUT — Operational amplifier output |
| پین 7 | +VS — Positive supply voltage |
| پین 8 | NC — Not connected |
| پین 9 | NC — Not connected |
| پین 10 | NC — Not connected |
| پین 11 | NC — Not connected |
| پین 12 | NC — Not connected |
| پین 13 | NC — Not connected |
| پین 14 | NC — Not connected |
| پین 15 | NC — Not connected |
| پین 16 | NC — Not connected |
کاربردهای معمول
AD745JR-16 مناسب است برای 6 کاربردs: Precision Sensor Signal Conditioning, Audio and Instrumentation Amplification, Photodiode and High-Impedance Buffering, Current Measurement Front Ends, Industrial Data Acquisition, Test and Measurement Signal Conditioning.
Precision Sensor Signal Conditioning
The AD745JR-16 fits low-level sensor interfaces because its JFET input stage provides very low input current, reducing loading on high-impedance sources, while its 20 MHz gain-bandwidth product preserves signal bandwidth. Place it in a non-inverting or differential conditioning stage ahead of an ADC or measurement converter. Compared with a general-purpose CMOS amplifier, the documented ultralow-noise, high-speed architecture better preserves small signals, although the exact noise density, input bias current, and common-mode limits must be checked for the selected grade.
پیشنهادی
Audio and Instrumentation Amplification
The AD745JR-16 is appropriate for precision audio and instrumentation paths where low voltage noise and moderate-to-high bandwidth are required together. Its 20 MHz gain-bandwidth product exceeds the useful range of many audio-only amplifiers, while the 12.5 V/µs slew rate improves response to larger transient waveforms. Use it in a low-gain preamplifier or line-level conditioning stage, and verify output drive, output swing, and stability against the intended load.
پیشنهادی
Photodiode and High-Impedance Buffering
A photodiode or capacitive sensor benefits from the AD745JR-16's low-input-current JFET stage because the source otherwise presents a very high impedance. The amplifier can buffer the sensor before a downstream sampling or transimpedance stage without contributing substantial loading. The 20 MHz bandwidth permits faster settling than many precision-only amplifiers, but photodiode capacitance, cable length, noise gain, and input-bias-current error must be included in the complete stability and sensitivity analysis.
پیشنهادی
Current Measurement Front Ends
The AD745JR-16 can amplify the small voltage produced by a shunt or current-sense element when low input bias current is important. Its JFET architecture avoids the higher bias currents commonly encountered with bipolar-input precision amplifiers, helping preserve measurement accuracy at high source impedance. The 20 MHz bandwidth allows the signal path to accommodate higher-frequency current waveforms, although designers should account for shunt impedance, common-mode voltage, amplifier offset, and the required gain-bandwidth product.
پیشنهادی
Industrial Data Acquisition
The AD745JR-16 works as an analog front-end amplifier for industrial data-acquisition systems requiring low-noise amplification over a broader bandwidth than a conventional precision amplifier. Its -40°C to +85°C industrial temperature range supports controlled equipment, and the ±4.8 V to ±18 V supply capability accommodates conventional bipolar analog rails. Pair it with suitable input filtering and an ADC, then verify noise, settling time, input-range limits, and system calibration across the operating temperature range.
پیشنهادی
Test and Measurement Signal Conditioning
The AD745JR-16 can condition low-level signals in test and measurement equipment while preserving the wide bandwidth needed for diagnostics and waveform capture. Its 20 MHz gain-bandwidth product and 12.5 V/µs slew rate provide more dynamic range than a slow precision-only op amp. Use it ahead of a higher-bandwidth converter when the source impedance is high enough to make low input bias current important, and check settling, output loading, and noise performance for the required measurement bandwidth.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای AD745JR-16 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | AD745KRZ-16 | AD745JRZ-16 | AD745AJR-16 | AD745BJR-16 | AD745CJR-16 |
|---|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC | 16-pin SOIC |
| Amplifier Type | Single JFET-input operational amplifier | Single JFET-input operational amplifier | Single JFET-input operational amplifier | AD745-family JFET-input operational amplifier | AD745-family JFET-input operational amplifier | AD745-family JFET-input operational amplifier |
| Number of Circuits | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit | 1 circuit |
| Gain-Bandwidth Product | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz | 20 MHz |
| Slew Rate | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs | 12.5 V/µs |
| Supply Voltage Range | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V | ±4.8 V to ±18 V |
تفاوتهای کلیدی
- Combines a JFET input stage with high speed (در مقابلAD745KRZ-16)
- Maintains the same 16-pin SOIC footprint (در مقابلAD745JRZ-16)
- Supports industrial-temperature operation (در مقابلAD745S)
یادداشتهای طراحی
Do not treat every AD745 order code as automatically interchangeable. The JR-16 suffix identifies a specific 16-pin SOIC configuration, while J, K, A, B, C, S, and Z suffix combinations can represent different temperature, qualification, or finish options. Before approving a substitution, compare the exact pinout, supply range, electrical limits, operating temperature, and qualification requirements. The package being the same 16-pin SOIC establishes footprint compatibility, not complete functional equivalence.
For high-impedance sources, minimize PCB leakage and contamination around the input pins because even a low input-bias-current amplifier can be disturbed by board-surface leakage. Keep the input traces short, avoid routing near switching nodes and high-impedance output traces, and use guarding techniques where practical. Include cable and probe capacitance in the stability analysis because the AD745's 20 MHz bandwidth is substantially higher than the bandwidth of many low-noise precision amplifiers.
Use the manufacturer's recommended supply-decoupling arrangement with short, low-inductance connections between the supply pins and local capacitors. The AD745JR-16 supports ±4.8 V to ±18 V operation, so verify that every powered terminal remains within its allowable limits, including during startup and shutdown. Do not apply a positive supply directly to the negative supply pin; provide a common ground reference or use the appropriate dual-rail arrangement for the chosen circuit topology.
Reserve the 16-pin SOIC footprint exactly according to the manufacturer land pattern, including all no-connect pins, and observe the standard pin-1 orientation. Keep the output route away from the input to minimize parasitic feedback, particularly when using inverting configurations with high gain. A ground plane should provide a low-impedance return for supply and signal currents, while analog and high-current switching paths should remain spatially separated.
اطلاعات انطباق
The AD745 family is not identified as an AEC-Q100 automotive product in the available documentation. The AD745S family option is available processed to MIL-STD-883B, Rev. C. Specific RoHS, REACH, lead-free, and halogen-free declarations for the exact order code require confirmation from the manufacturer.