AD977BRRL - 16-Bit 100 kSPS SAR ADC | Analog Devices
MPN: AD977BRRL ✗ Cuối đờiAD977BRRL Tóm tắt
An ADC converts an analog voltage into a digital number for processing by a microcontroller, DSP, FPGA, or other digital controller. The AD977 belongs to the successive-approximation ADC category within the broader ADC and data-converter semiconductor hierarchy. Its internal switched-capillator architecture performs one conversion through a sequence of binary-weighted comparisons, allowing the 16-bit result to be transferred through a serial interface.
Key features include 100 kSPS throughput, 16-bit resolution, single 5 V operation, a serial SPI data interface, factory calibration, and a power-down mode. The manufacturer also tests the devices for signal-to-noise ratio and total harmonic distortion in addition to conventional offset, gain, and linearity specifications. These characteristics make the converter suitable for industrial instrumentation, sensor interfaces, process monitoring, and embedded measurement systems.
The switched-capitor SAR architecture provides deterministic sampling and conversion behavior while limiting power dissipation to 100 mW maximum. Because the converter is not a high-frequency pipeline ADC, it is better suited to continuous precision measurements than to waveform capture at megahertz rates. The SPI interface reduces the number of required signal connections and supports compact PCB layouts where pin count and routing simplicity are important.
Typical uses include digital pressure and temperature instrumentation, laboratory data acquisition, industrial process control, factory monitoring, and low-rate sensor signal capture. In these applications, the 100 kSPS rate is sufficient for many control and monitoring loops, while 16-bit resolution preserves fine amplitude distinctions after conversion. The single 5 V supply also simplifies analog and digital power architecture when the surrounding system already operates at 5 V.
When laying out the circuit, treat the analog input, reference, and ground connections as sensitive signal paths even though the sampling rate is relatively low. Place input and reference decoupling capacitors near their associated pins, keep digital clock and serial-data traces away from the analog input, and use a stable reference source. Follow the manufacturer datasheet pin-description table when assigning PCB tracks and verify the complete power-up sequence in the final system.
This product page consolidates the manufacturer specifications, package details, interface characteristics, selection guidance, and pin-compatible comparison information into one engineering-focused reference. It also distinguishes the AD977BRRL from related family members whose speed, package, or ordering options differ, helping designers verify replacement suitability before committing a PCB layout to production.
Bộ thay thế dễ dàng lắp đặt cho AD977BRRL — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
AD977ARRL
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD977ABRL
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD977BRZRL
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
AD977BRRL Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 16 bit |
| Tỷ lệ lấy mẫu | 100 kSPS |
| Input Count | 1 input |
| Architecture | Successive-approximation, switched-capillator |
| Điện áp cung cấp | 5 V single supply |
| Maximum Power Dissipation | 100 mW |
| Digital Interface | Serial SPI |
| Hộp | 20-lead SOIC |
| Package Width | 7.50 mm |
| Package Body Width | 0.295 inch |
| Kiểu lắp đặt | Surface mount |
| Terminal Count | 20 terminals |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| Temperature Grade | Industrial |
| Power-Down Mode | Supported |
| Factory Calibration | Supported |
| DC and AC Testing | Offset, gain, linearity, SNR, and THD |
| Packaging | Tape and reel |
Hướng dẫn cấu hình chân AD977BRRL rectangular
Cấu hình chân cho AD977BRRL (rectangular gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho AD977BRRL.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
AD977BRRL phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Process Control Instrumentation, Laboratory Data Acquisition, Digital Pressure Measurement, Power-Supply Monitoring, Embedded Test and Measurement.
Industrial Sensor Acquisition
The AD977BRRL fits industrial sensor acquisition when the measured signal requires 16-bit resolution but only a 100 kSPS sampling rate. Its single 5 V supply and maximum 100 mW power dissipation simplify embedded measurement electronics. Place the converter behind an anti-alias filter and low-noise input buffer, and use its SPI interface to transfer each conversion to a controller. The 100 kSPS throughput supports fast monitoring loops without the power and complexity of a high-speed pipeline ADC.
Được đề xuất
Process Control Instrumentation
The AD977BRRL is suitable for process-control measurements where a controller must digitize a single analog variable with 16-bit precision. At 100 kSPS, it can update a supervisory or proportional control loop faster than many slow sensor systems require. Its single 5 V operation permits direct participation in a 5 V analog rail, while the serial SPI interface reduces wiring to the controller. Input settling, reference stability, and grounding remain critical to repeatable process readings.
Được đề xuất
Laboratory Data Acquisition
The AD977BRRL can serve as the measurement ADC in a compact laboratory data-acquisition front end that emphasizes resolution and low power rather than waveform capture. The 100 kSPS rate is appropriate for temperature, pressure, strain-gauge, and slowly varying laboratory signals. Its 16-bit output provides fine numerical granularity, and the SPI interface allows a microcontroller to capture, timestamp, and process measurements. A low-noise reference and carefully isolated analog layout are essential for laboratory accuracy.
Được đề xuất
Digital Pressure Measurement
The AD977BRRL fits digital pressure transmitters and pressure-controller modules where the transducer output is slow enough for a 100 kSPS SAR conversion. The converter’s 16-bit resolution can represent small pressure-related voltage changes without requiring a parallel ADC. Use an instrumentation front end to condition the bridge or sensor output, then connect the AD977BRRL to a controller through SPI. Stable reference voltage and short analog traces help prevent gain drift from being interpreted as pressure variation.
Được đề xuất
Power-Supply Monitoring
The AD977BRRL can monitor a scaled voltage in a power-supply or battery-management subsystem when feedback precision matters more than waveform bandwidth. A 100 kSPS sampling rate supports supervisory measurements of an output rail, while 16-bit resolution captures small deviations after suitable attenuation. The converter operates from a single 5 V supply and has a maximum power dissipation of 100 mW. Its serial interface makes it practical for central diagnostics with multiple measurements handled through multiplexing.
Được đề xuất
Embedded Test and Measurement
The AD977BRRL is appropriate for embedded test equipment that measures one analog channel with high numerical resolution and modest acquisition bandwidth. Examples include production-line testers, board monitors, and portable diagnostic instruments. Its 100 kSPS rate allows repeated single-shot or small-block acquisitions, while SPI supports connection to a microcontroller without a wide parallel bus. Component selection should account for the obsolete lifecycle status, so new production designs should verify long-term supply before committing the layout.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho AD977BRRL — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | AD977ARRL | AD977ABRL | AD977BRZRL |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-lead SOIC | 20-lead SOIC | 20-lead SOIC | 20-lead SOIC |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit |
| Input Count | 1 input | 1 input | 1 input | 1 input |
| Supply Voltage | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply |
| Digital Interface | Serial SPI | Serial SPI | Serial SPI | Serial SPI |
| Architecture | Successive-approximation, switched-capillator | Successive-approximation, switched-capulator | Successive-approximation, switched-capulator | Successive-approximation, switched-capulator |
Bảo phân biệt quan trọng
- Moderate sampling rate in a 16-bit SAR architecture (vsAD977ABRL)
- Single-channel conversion with serial data transfer (vsAD977ARRL)
- Low-power operation from a single rail (vsAD977BRZRL)
Ghi chú thiết kế
Route the analog input and reference connections away from SPI clock and data traces. Place the input and reference capacitors at the corresponding IC pins, use a compact analog path, and provide a quiet ground-return plane. Crosstalk and reference disturbance can appear directly in the 16-bit result even though the converter operates at only 100 kSPS.
Use the manufacturer’s recommended analog and digital supply arrangements and decoupling values. The AD977BRRL operates from a single 5 V supply, but reference and input circuitry may require additional filtering. Keep switching-regulator routing and magnetics away from the converter to prevent supply ripple from degrading SNR and THD.
Do not substitute an AD977A-family part without checking conversion timing and pin assignments. The AD977A reaches 200 kSPS, twice the AD977 rate, and related ordering codes can use different package or temperature options. Confirm supply voltage, analog input range, reference requirement, SPI timing, power-down behavior, and all 20 physical pins in the manufacturer datasheet.
Treat the reference as an analog signal and keep its return path short and continuous. Reference drift multiplies directly into the converted result, while source impedance and capacitor selection affect settling before conversion. Validate the complete input network for the highest expected source impedance and verify the available acquisition time against the manufacturer’s acquisition specifications.
Thông tin tuân thủ
The industrial temperature grade is confirmed, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated. AEC-Q100 is not applicable to this industrial ADC unless a separate automotive qualification is established.