AD977BRRL - 16-Bit 100 kSPS SAR ADC | Analog Devices
MPN: AD977BRRL ✗ 停產AD977BRRL 概覽
An ADC converts an analog voltage into a digital number for processing by a microcontroller, DSP, FPGA, or other digital controller. The AD977 belongs to the successive-approximation ADC category within the broader ADC and data-converter semiconductor hierarchy. Its internal switched-capillator architecture performs one conversion through a sequence of binary-weighted comparisons, allowing the 16-bit result to be transferred through a serial interface.
Key features include 100 kSPS throughput, 16-bit resolution, single 5 V operation, a serial SPI data interface, factory calibration, and a power-down mode. The manufacturer also tests the devices for signal-to-noise ratio and total harmonic distortion in addition to conventional offset, gain, and linearity specifications. These characteristics make the converter suitable for industrial instrumentation, sensor interfaces, process monitoring, and embedded measurement systems.
The switched-capitor SAR architecture provides deterministic sampling and conversion behavior while limiting power dissipation to 100 mW maximum. Because the converter is not a high-frequency pipeline ADC, it is better suited to continuous precision measurements than to waveform capture at megahertz rates. The SPI interface reduces the number of required signal connections and supports compact PCB layouts where pin count and routing simplicity are important.
Typical uses include digital pressure and temperature instrumentation, laboratory data acquisition, industrial process control, factory monitoring, and low-rate sensor signal capture. In these applications, the 100 kSPS rate is sufficient for many control and monitoring loops, while 16-bit resolution preserves fine amplitude distinctions after conversion. The single 5 V supply also simplifies analog and digital power architecture when the surrounding system already operates at 5 V.
When laying out the circuit, treat the analog input, reference, and ground connections as sensitive signal paths even though the sampling rate is relatively low. Place input and reference decoupling capacitors near their associated pins, keep digital clock and serial-data traces away from the analog input, and use a stable reference source. Follow the manufacturer datasheet pin-description table when assigning PCB tracks and verify the complete power-up sequence in the final system.
This product page consolidates the manufacturer specifications, package details, interface characteristics, selection guidance, and pin-compatible comparison information into one engineering-focused reference. It also distinguishes the AD977BRRL from related family members whose speed, package, or ordering options differ, helping designers verify replacement suitability before committing a PCB layout to production.
直接替換替代品,適用於 AD977BRRL — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。
AD977ARRL
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD977ABRL
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD977BRZRL
✅ 直接替換 ⚠️ 規格未經驗證📋 參考替代品(不在目錄中)
AD977BRRL 最大額定值與電氣特性
| 解析度 | 16 bit |
| 取樣率 | 100 kSPS |
| Input Count | 1 input |
| Architecture | Successive-approximation, switched-capillator |
| 供應電壓 | 5 V single supply |
| Maximum Power Dissipation | 100 mW |
| Digital Interface | Serial SPI |
| 封裝 | 20-lead SOIC |
| Package Width | 7.50 mm |
| Package Body Width | 0.295 inch |
| 安裝類型 | Surface mount |
| Terminal Count | 20 terminals |
| Package Shape | Rectangular |
| Lead Form | Gull wing |
| Temperature Grade | Industrial |
| Power-Down Mode | Supported |
| Factory Calibration | Supported |
| DC and AC Testing | Offset, gain, linearity, SNR, and THD |
| Packaging | Tape and reel |
AD977BRRL rectangular 腳位配置指南
AD977BRRL(rectangular 封裝)的腳位配置。 此類比元件具有輸入、輸出與電源腳位。偏移歸零、補償與致能腳位配置請參閱製造商資料表。適用於訊號調理與放大器電路。
無詳細腳位定義資料: AD977BRRL.
請參閱 資料表 以查看完整腳位配置。
典型應用
AD977BRRL 適用於 6 應用s: Industrial Sensor Acquisition, Process Control Instrumentation, Laboratory Data Acquisition, Digital Pressure Measurement, Power-Supply Monitoring, Embedded Test and Measurement.
Industrial Sensor Acquisition
The AD977BRRL fits industrial sensor acquisition when the measured signal requires 16-bit resolution but only a 100 kSPS sampling rate. Its single 5 V supply and maximum 100 mW power dissipation simplify embedded measurement electronics. Place the converter behind an anti-alias filter and low-noise input buffer, and use its SPI interface to transfer each conversion to a controller. The 100 kSPS throughput supports fast monitoring loops without the power and complexity of a high-speed pipeline ADC.
推薦
Process Control Instrumentation
The AD977BRRL is suitable for process-control measurements where a controller must digitize a single analog variable with 16-bit precision. At 100 kSPS, it can update a supervisory or proportional control loop faster than many slow sensor systems require. Its single 5 V operation permits direct participation in a 5 V analog rail, while the serial SPI interface reduces wiring to the controller. Input settling, reference stability, and grounding remain critical to repeatable process readings.
推薦
Laboratory Data Acquisition
The AD977BRRL can serve as the measurement ADC in a compact laboratory data-acquisition front end that emphasizes resolution and low power rather than waveform capture. The 100 kSPS rate is appropriate for temperature, pressure, strain-gauge, and slowly varying laboratory signals. Its 16-bit output provides fine numerical granularity, and the SPI interface allows a microcontroller to capture, timestamp, and process measurements. A low-noise reference and carefully isolated analog layout are essential for laboratory accuracy.
推薦
Digital Pressure Measurement
The AD977BRRL fits digital pressure transmitters and pressure-controller modules where the transducer output is slow enough for a 100 kSPS SAR conversion. The converter’s 16-bit resolution can represent small pressure-related voltage changes without requiring a parallel ADC. Use an instrumentation front end to condition the bridge or sensor output, then connect the AD977BRRL to a controller through SPI. Stable reference voltage and short analog traces help prevent gain drift from being interpreted as pressure variation.
推薦
Power-Supply Monitoring
The AD977BRRL can monitor a scaled voltage in a power-supply or battery-management subsystem when feedback precision matters more than waveform bandwidth. A 100 kSPS sampling rate supports supervisory measurements of an output rail, while 16-bit resolution captures small deviations after suitable attenuation. The converter operates from a single 5 V supply and has a maximum power dissipation of 100 mW. Its serial interface makes it practical for central diagnostics with multiple measurements handled through multiplexing.
推薦
Embedded Test and Measurement
The AD977BRRL is appropriate for embedded test equipment that measures one analog channel with high numerical resolution and modest acquisition bandwidth. Examples include production-line testers, board monitors, and portable diagnostic instruments. Its 100 kSPS rate allows repeated single-shot or small-block acquisitions, while SPI supports connection to a microcontroller without a wide parallel bus. Component selection should account for the obsolete lifecycle status, so new production designs should verify long-term supply before committing the layout.
推薦
推薦產品摘要
工程參考資料,適用於 AD977BRRL — 比較、設計指引及合規資訊。
選型指南
與替代品比較
| 參數 | 本產品 | AD977ARRL | AD977ABRL | AD977BRZRL |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 20-lead SOIC | 20-lead SOIC | 20-lead SOIC | 20-lead SOIC |
| Resolution | 16 bit | 16 bit | 16 bit | 16 bit |
| Input Count | 1 input | 1 input | 1 input | 1 input |
| Supply Voltage | 5 V single supply | 5 V single supply | 5 V single supply | 5 V single supply |
| Digital Interface | Serial SPI | Serial SPI | Serial SPI | Serial SPI |
| Architecture | Successive-approximation, switched-capillator | Successive-approximation, switched-capulator | Successive-approximation, switched-capulator | Successive-approximation, switched-capulator |
主要差異化特點
- Moderate sampling rate in a 16-bit SAR architecture (對比AD977ABRL)
- Single-channel conversion with serial data transfer (對比AD977ARRL)
- Low-power operation from a single rail (對比AD977BRZRL)
設計說明
Route the analog input and reference connections away from SPI clock and data traces. Place the input and reference capacitors at the corresponding IC pins, use a compact analog path, and provide a quiet ground-return plane. Crosstalk and reference disturbance can appear directly in the 16-bit result even though the converter operates at only 100 kSPS.
Use the manufacturer’s recommended analog and digital supply arrangements and decoupling values. The AD977BRRL operates from a single 5 V supply, but reference and input circuitry may require additional filtering. Keep switching-regulator routing and magnetics away from the converter to prevent supply ripple from degrading SNR and THD.
Do not substitute an AD977A-family part without checking conversion timing and pin assignments. The AD977A reaches 200 kSPS, twice the AD977 rate, and related ordering codes can use different package or temperature options. Confirm supply voltage, analog input range, reference requirement, SPI timing, power-down behavior, and all 20 physical pins in the manufacturer datasheet.
Treat the reference as an analog signal and keep its return path short and continuous. Reference drift multiplies directly into the converted result, while source impedance and capacitor selection affect settling before conversion. Validate the complete input network for the highest expected source impedance and verify the available acquisition time against the manufacturer’s acquisition specifications.
合規資訊
The industrial temperature grade is confirmed, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations are not stated. AEC-Q100 is not applicable to this industrial ADC unless a separate automotive qualification is established.