ADF4106SRUZ-EP 6 GHz PLL Synthesizer | Analog Devices
MPN: ADF4106SRUZ-EP ✓ Hoạt độngADF4106SRUZ-EP Tóm tắt
A phase-locked loop, or PLL, is a feedback-controlled timing system that locks an oscillator to a stable reference frequency. Within the broader RF and wireless hierarchy, the ADF4106 is a clock-generation and timing IC used to develop programmable local oscillators for receiver and transmitter conversion stages. Its integer-N architecture is especially useful when predictable frequency steps, repeatable programming, and compact implementation are more important than fractional-N flexibility.
The device combines a programmable reference divider with a programmable prescaler, A counter, and B counter, allowing the output frequency to be set through a serial interface. According to the manufacturer datasheet, the architecture supports synthesis up to 6 GHz and includes a low-noise digital phase-frequency detector and precision charge pump. These characteristics make the part appropriate for RF tuning planes, microwave conversion chains, instrumentation, and controlled aerospace or defense equipment.
The ADF4106SRUZ-EP is differentiated from the standard ADF4106 product by its -55°C to +125°C operating range, controlled manufacturing baseline, single assembly and test site, single fabrication site, enhanced product-change notification, and AQEC-oriented qualification support. The suffix denotes an enhanced-product configuration rather than a different PLL architecture. The manufacturer product page also identifies availability of qualification data on request.
Typical uses include local-oscillator generation in wireless receivers, local-oscillator generation in wireless transmitters, microwave up-conversion and down-conversion, frequency-agile test equipment, and defense or aerospace RF subsystems. The 16-lead TSSOP keeps the implementation compact while exposing the programming and analog control interfaces needed for a closed-loop synthesizer.
When laying out the circuit, preserve continuous reference and feedback paths, place the loop-filter components close to their associated pins, and provide stable supply bypassing. The reference input and prescaler feedback are especially sensitive to layout discontinuities. Component values for the loop filter and charge-pump current should be calculated from the intended reference frequency, division ratio, phase-noise target, and settling-time requirement rather than copied without regard to those operating conditions.
This product summary combines the ADF4106-EP functional description, package and temperature information, lifecycle context, and practical guidance for evaluating the ADF4106SRUZ-EP in an RF timing design. It also highlights the key engineering distinction between ordinary ADF4106 variants and the EP product intended for controlled defense and aerospace manufacturing environments.
Bộ thay thế dễ dàng lắp đặt cho ADF4106SRUZ-EP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF4106SRUZ-EP (cùng hình factor và footprint) — khác nhau ở Charge Pump, Device Type, Package, Phase-Frequency Detector.
ADF4106SRU-EP
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4156BRUZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4106SRUZ-EP Thông số kỹ thuật
| Device Type | Integer-N frequency synthesizer / phase-locked loop |
| Maximum Synthesized Frequency | 6 GHz |
| Reference Divider | Programmable |
| Prescaler | Programmable dual-modulus P/P+1 |
| A Counter | 6-bit programmable |
| B Counter | 21-bit programmable |
| Phase-Frequency Detector | Low-noise digital type |
| Charge Pump | Precision programmable type |
| Khoảng nhiệt độ hoạt động | -55°C to +125°C |
| Hộp | 16-lead TSSOP, 4.40 mm width |
| Kiểu lắp đặt | Surface mount |
| Product Qualification Standard | AQEC |
| Manufacturing Sites | 1 fabrication site and 1 assembly/test site |
| Qualification Data | Available upon request |
Hướng dẫn cấu hình chân ADF4106SRUZ-EP 16-lead tssop, 4.40 mm width
Cấu hình chân cho ADF4106SRUZ-EP (16-lead tssop, 4.40 mm width gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADF4106SRUZ-EP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADF4106SRUZ-EP phù hợp cho 6 Áp dụngs: Wireless Receiver Local Oscillator, Wireless Transmitter Up-Conversion, Microwave Down-Conversion, Aerospace RF Subsystem, Defense Communications Equipment, RF Test and Measurement Instrument.
Wireless Receiver Local Oscillator
The ADF4106SRUZ-EP fits receiver local-oscillator generation because its 6 GHz maximum synthesized frequency, programmable prescaler, and programmable A and B counters permit division ratios to be selected for RF tuning stages. The low-noise digital phase-frequency detector and precision charge pump support the closed-loop frequency-generation function. Its 16-lead TSSOP format keeps the synthesizer compact, while the -55°C to +125°C range addresses controlled environmental requirements. Designers should calculate the loop filter from the reference frequency, prescaler, division ratio, target phase noise, and required settling time.
Được đề xuất
Wireless Transmitter Up-Conversion
The ADF4106SRUZ-EP can generate the programmable local oscillator used in a wireless transmitter up-conversion chain. Its maximum 6 GHz operating capability accommodates microwave and RF conversion stages, while the programmable reference divider, dual-modulus prescaler, and 6-bit A counter establish the required division relationship. The precision charge pump and low-noise phase-frequency detector are central to closing the loop and suppressing phase noise. RF board layout should minimize loop-filter perturbation and maintain controlled return paths from the charge-pump output.
Được đề xuất
Microwave Down-Conversion
The ADF4106SRUZ-EP is suitable for a microwave down-conversion local oscillator because it supports synthesis up to 6 GHz and offers programmable prescaler and counter paths for setting the required RF channel. The -55°C to +125°C operating range makes it relevant to controlled industrial, defense, and aerospace environments. The mixer and downstream circuitry will determine the full signal-chain performance, but the synthesizer must still deliver adequate phase noise and lock behavior. Loop-filter design and reference routing should therefore be evaluated as part of the complete conversion-path design.
Được đề xuất
Aerospace RF Subsystem
The ADF4106SRUZ-EP addresses aerospace RF subsystems that need a programmable 6 GHz frequency source within a -55°C to +125°C operating range. Its EP product configuration supports controlled manufacturing with one fabrication site, one assembly and test site, enhanced product-change notification, and qualification data available upon request. These attributes are more relevant than generic performance claims when preparing a qualified design. Program teams should still verify the exact device configuration, qualification evidence, and intended mission environment with the manufacturer.
Được đề xuất
Defense Communications Equipment
The ADF4106SRUZ-EP can support programmable local-oscillator generation in defense communications equipment where stable frequency synthesis and an extended -55°C to +125°C operating range are required. Its 6 GHz ceiling, programmable dual-modulus prescaler, and independently programmable reference and counter blocks provide flexible division-ratio generation. The compact 16-lead TSSOP helps limit board area in multi-channel RF assemblies. Signal-integrity measures should include a short reference path, careful charge-pump loop-filter routing, and stable supply decoupling around the device.
Được đề xuất
RF Test and Measurement Instrument
The ADF4106SRUZ-EP is useful in RF test equipment that requires a programmable local oscillator across multiple division ratios and frequencies up to 6 GHz. The integer-N architecture provides a straightforward implementation for stable instrument channels, while the serial-programming controls support automated frequency selection. Accuracy depends on the reference oscillator, divider ratios, loop bandwidth, and charge-pump settings rather than the maximum frequency label alone. For laboratory-grade phase-noise performance, calculate the loop filter from the desired integration bandwidth and compare measured results against the datasheet test conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF4106SRUZ-EP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADF4106SRU-EP | ADF4156BRUZ |
|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-lead TSSOP, 4.40 mm width | 16-lead TSSOP | 16-lead TSSOP |
| Maximum Synthesized Frequency | 6 GHz | 6 GHz | 6 GHz |
| Product Configuration | ADF4106-EP with AQEC-oriented support | ADF4106-EP family | ADF4156 family |
Bảo phân biệt quan trọng
- Extended military temperature operation (vsADF4106SRU-EP)
- Controlled EP manufacturing configuration (vsADF4156BRUZ)
- Programmable RF synthesis architecture (vsADF4156BRUZ)
Ghi chú thiết kế
Keep the reference input, prescaler feedback, and charge-pump loop-filter paths compact and away from noisy switching nodes. Ground the exposed return connections according to the package drawing and preserve a continuous ground reference beneath the device where the PCB design permits it. In an RF board, fixed vias and short loop-filter connections reduce parasitic inductance that can otherwise create phase-error peaks, unexpected ringing, or poor lock repeatability.
Do not select the prescaler or division-ratio limits without checking the relationship between the reference frequency, A counter, B counter, and requested output. The 6 GHz headline value is a maximum capability, not a guarantee that every output is realizable under all divider combinations. Program the device according to the register definitions in the manufacturer datasheet and confirm that the calculated lock frequency remains within the valid operating range.
Calculate the loop filter from the actual reference frequency, prescaler, division ratio, target phase noise, and settling-time requirement. Start with the charge-pump current and passive values recommended by the manufacturer, then verify lock behavior and phase noise on the final board. Changes to reference routing, power-supply impedance, or feedback isolation can alter loop performance, so measurement on representative hardware is preferable to relying only on nominal counter settings.
Thông tin tuân thủ
The manufacturer identifies the EP product as supporting the AQEC standard, with a -55°C to +125°C military temperature range and qualification data available upon request. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statuses were not established.