ADF4001BRUZ-R7 - 200MHz PLL Clock Generator | Analog Devices
MPN: ADF4001BRUZ-R7 ✓ Hoạt độngADF4001BRUZ-R7 Tóm tắt
An integrated PLL is a feedback-controlled frequency synthesizer that compares a reference signal with a divided feedback signal, drives an external voltage-controlled oscillator or voltage-controlled crystal oscillator through a charge pump and loop filter, and locks the output to a stable frequency. Clock-generator PLLs belong to the broader clock and timing IC hierarchy and are used where a fixed or divided system clock is insufficient and precise, programmable frequency generation is required.
The ADF4001 supports reference input frequencies that can be selected through its programmable reference divider. Its separate charge-pump supply permits a higher tuning voltage in 5 V systems, while programmable charge-pump currents provide flexibility when tuning loop-filter behavior. Hardware and software power-down modes help reduce consumption when the synthesizer is not required. Analog and digital lock-detect outputs allow a controller to monitor whether the loop has acquired the intended frequency.
A three-wire serial interface provides programming access for the counters and control functions. The device includes a low-noise digital phase-frequency detector and precision charge pump, supporting low-noise clock generation and stable PLL reference sources. The 16-lead TSSOP package is compatible with the ADF4110, ADF4111, ADF4112, and ADF4113 family according to the manufacturer datasheet, which can simplify platform qualification and board-level standardization.
Typical uses include wireless-infrastructure reference clocks, instrumentation clocks, low-frequency RF synthesizers, clock-cleaning systems, and communication equipment requiring programmable division or multiplication. In a VCXO-based design, the charge-pump output drives the loop filter and tuning input of the oscillator, while the oscillator output feeds the RF input and reference path through suitable matching.
PCB design should keep the serial programming traces away from sensitive RF and charge-pump paths, provide solid ground-plane continuity, and place loop-filter components close to the charge-pump and VCO-related pins. Designers must also observe the difference between the 2.7 V to 5.5 V device supply and the separately supplied charge-pump voltage, particularly when operating in a 5 V system.
This page combines the manufacturer specifications with practical PLL design guidance, package-level pin information, application examples, and a structured comparison of genuine same-package alternatives for engineers evaluating clock-generator upgrades.
Bộ thay thế dễ dàng lắp đặt cho ADF4001BRUZ-R7 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADF4001BRUZ-R7 (cùng hình factor và footprint) — khác nhau ở Device Type, Package, Power-Down Modes, Serial Interface, Family Compatibility.
ADF4001BRUZ-RL
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADF4001BRUZ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4001BRU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADF4001BRUZ-R7 Thông số kỹ thuật
| Device Type | 200 MHz clock-generator PLL |
| PLL Bandwidth | 200 MHz |
| Output Channel Count | 1 channel |
| Power Supply Range | 2.7 V to 5.5 V |
| Separate Charge Pump Supply | Supported |
| Charge Pump Current | Programmable |
| Serial Interface | 3-wire |
| Power-Down Modes | Hardware and software |
| Lock Detect | Analog and digital |
| Typical Operating Current | 4.5 mA |
| N Counter | 13-bit programmable |
| R Counter | 14-bit programmable |
| Hộp | 16-lead TSSOP, 4.40 mm width |
| Nhiệt độ hoạt động | -40 °C to +85 °C |
| Trạng thái vòng đời | Production |
| Family Compatibility | ADF4110, ADF4111, ADF4112 and ADF4113 |
| Trạng thái RoHS | Compliant |
| REACH Status | Unaffected |
Cấu hình chân ADF4001BRUZ-R7
| Chân 1 | REFIN — Reference input |
| Chân 2 | CP — Charge-pump output |
| Chân 3 | VCO — Voltage-controlled oscillator input |
| Chân 4 | GND — Ground |
| Chân 5 | R — R-counter setting input |
| Chân 6 | N — N-counter setting input |
| Chân 7 | A — Programming data input |
| Chân 8 | B — Programming clock input |
| Chân 9 | VP — Charge-pump supply |
| Chân 10 | VDD — Analog and digital supply |
| Chân 11 | CLK — Programming clock input |
| Chân 12 | DATA — Programming data input |
| Chân 13 | LE — Programming latch enable |
| Chân 14 | SYNC — Power-down synchronization input |
| Chân 15 | MUXOUT — Multiplexer output |
| Chân 16 | CE — Chip enable |
Ứng dụng tiêu biểu
ADF4001BRUZ-R7 phù hợp cho 6 Áp dụngs: Wireless Infrastructure Clock Generation, Instrumentation and Test Equipment Clocks, VCXO-Based Frequency Standard, RF Local Oscillator Reference, Clock Cleaning and Jitter Reduction, Communication Equipment Timing Reference.
Wireless Infrastructure Clock Generation
The ADF4001BRUZ-R7 fits wireless-infrastructure clock-generation systems requiring a stable, programmable reference with low phase noise. Its 200 MHz PLL bandwidth, 14-bit R counter and 13-bit N counter allow the reference and synthesis ratios to be programmed for system clocks or local-oscillator references. The 4.5 mA typical operating current helps control power demand, while analog and digital lock detection lets baseband hardware confirm acquisition. Place the charge-pump path and loop filter away from high-speed digital return currents to preserve phase-noise margin.
Được đề xuất
Instrumentation and Test Equipment Clocks
The ADF4001BRUZ-R7 can generate stable clocks for instrumentation systems that require programmable division, multiplication or frequency synthesis from a single reference. A 2.7 V to 5.5 V operating range supports both lower-voltage and 5 V system architectures, while the separate charge-pump supply provides additional tuning headroom. The three-wire interface allows a microcontroller or test controller to configure the 13-bit N counter and 14-bit R counter. Use lock detection before enabling sensitive measurement circuitry, and isolate the reference input from high-current switching nodes.
Được đề xuất
VCXO-Based Frequency Standard
The ADF4001BRUZ-R7 is appropriate for a VCXO-based frequency standard where a crystal oscillator must be corrected against a stable reference. Its charge-pump output drives the loop filter and oscillator tuning input, while oscillator feedback returns to the RF input for phase comparison. The manufacturer example uses a 13 MHz VCXO and a T-network for 50 Ω matching between the oscillator output, REFIN path and RFIN input. Component selection must account for the actual oscillator gain, tuning range and required phase noise.
Được đề xuất
RF Local Oscillator Reference
The ADF4001BRUZ-R7 can support an RF local-oscillator reference architecture by synthesizing the required reference frequency from an external source. Its low-noise digital phase-frequency detector and precision charge pump are useful when phase-noise performance is more important than the simplicity of a fixed divider. The separate charge-pump supply is valuable in 5 V systems that require an extended tuning voltage. Keep the loop-filter components compact and terminated close to CP, and route RFIN and REFIN as controlled-impedance paths if their operating frequencies require it.
Được đề xuất
Clock Cleaning and Jitter Reduction
The ADF4001BRUZ-R7 can serve as the synthesizer element in a clock-cleaning system that removes accumulated timing error from an incoming reference. Programmable reference and feedback ratios allow a common source frequency to be converted into the required system clock, while lock detect provides a usable acquisition indication. The 4.5 mA typical current is valuable in portable test equipment, and the 16-lead TSSOP package simplifies compact implementation. Validate loop bandwidth against the input jitter spectrum rather than optimizing only for capture range.
Được đề xuất
Communication Equipment Timing Reference
The ADF4001BRUZ-R7 provides programmable frequency synthesis for communication equipment requiring a stable internal timing reference. The 200 MHz bandwidth supports reference-clock generation, the three-wire interface supports direct microcontroller configuration, and hardware or software power-down can disable activity during inactive operating intervals. Analog and digital lock outputs allow the host to distinguish a locked reference from an unlocked loop before enabling downstream transmitters or converters. Design the grounding and return paths so reference noise is not coupled from switching supplies or digital processors.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADF4001BRUZ-R7 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADF4001BRUZ-RL | ADF4001BRUZ | ADF4001BRU |
|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Package | 16-lead TSSOP | 16-lead TSSOP - same | 16-lead TSSOP - same | 16-lead TSSOP - same |
| Device Type | 200 MHz clock-generator PLL | ADF4001 family clock-generator PLL | ADF4001 family clock-generator PLL | ADF4001 family clock-generator PLL |
| PLL Bandwidth | 200 MHz | 200 MHz | 200 MHz | 200 MHz |
| Power Supply Range | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V | 2.7 V to 5.5 V |
| Typical Operating Current | 4.5 mA | 4.5 mA | 4.5 mA | 4.5 mA |
| Serial Interface | 3-wire | 3-wire | 3-wire | 3-wire |
| Lock Detect | Analog and digital | Analog and digital | Analog and digital | Analog and digital |
| Ordering and Packing Difference | -R7 configuration | -RL temperature-grade suffix | Base -BRUZ ordering option | Base family ordering option |
Bảo phân biệt quan trọng
- High-bandwidth clock synthesis in a compact package (vsADF4001BRUZ)
- Separate charge-pump supply supports extended tuning (vsADF4001BRUZ-RL)
- Programmable acquisition monitoring and shutdown (vsADF4001BRU)
Ghi chú thiết kế
Route the charge-pump output from CP directly into the loop-filter network, and place the filter components close to the relevant pins. Keep the CP and VCO traces short and controlled-impedance when required by the operating frequency. Do not run these sensitive paths beneath digital programming traces or between noisy switching nodes, because parasitic coupling can increase phase noise or produce reference spurs.
The 2.7 V to 5.5 V main supply and the separate charge-pump supply serve different circuit functions. Decouple each supply locally and follow the manufacturer's recommended capacitor arrangement. In a 5 V system, verify the permitted VP range before using it to extend the oscillator tuning voltage; exceeding the charge-pump or main-supply limit can compromise tuning range, reliability or component life.
Do not interpret the 200 MHz PLL bandwidth as an unconditional output-frequency limit. The achievable operating range depends on the reference frequency, counter division ratios, VCO gain, tuning range, loop filter and phase-noise requirements. Program the 13-bit N counter and 14-bit R counter within their valid ranges, and verify lock behavior across temperature, supply and process corners before releasing the design.
Treat REFIN and RFIN as precision inputs rather than ordinary digital nets. Terminate them according to the selected reference source and oscillator interface, minimize discontinuities, and keep the return path close to the signal path. If a T-network provides the 50 Ω matching shown in the manufacturer's VCXO example, calculate resistor and capacitor values for the actual source impedance and operating frequency rather than copying them without validation.
Thông tin tuân thủ
RoHS compliance and REACH unaffected status are identified for the exact ADF4001BRUZ-R7 component. The ADF4001 family is listed in production by Analog Devices. No automotive qualification, lead-free statement, halogen-free statement or conflict-minerals declaration was established for this ordering code.