ADM3075EYRZ - 500 kbps RS-485 Transceiver | Analog Devices
MPN: ADM3075EYRZ ✓ Hoạt độngADM3075EYRZ Tóm tắt
An RS-485 transceiver is the physical-layer interface between a logic-level controller and a balanced, multipoint bus. The differential signaling improves noise immunity, supports longer cable runs than single-ended interfaces, and allows multiple nodes to share a bus when their combined load permits it. The related RS-422 operating mode supports balanced point-to-point communication using the same transceiver family.
Key characteristics include a 3.3 V supply, a maximum signaling rate of 500 kbps, 1/8-unit-load bus loading, half-duplex operation, and ±15 kV ESD protection on the bus-facing pins. The DE and RE inputs allow the host to place the transmitter and receiver into high-impedance states when the controller is not actively driving or receiving data. A fail-safe receiver function helps the output remain in a defined state when the bus is idle or the driver is disabled.
The ADM3075E family is intended for industrial instrumentation, communications equipment, security systems, sensing equipment, and data-acquisition systems operating on RS-485 or RS-422 networks. Its 500 kbps capability suits moderate-speed control links, position feedback, remote sensors, industrial gateways, and supervisory communication rather than high-speed backbone traffic.
A half-duplex design requires only one pair of bus conductors, but software must control bus turnaround so that the driver does not contend with an active remote transmitter. Leave adequate termination at both physical ends of the bus and use the specified biasing arrangement to hold the differential bus at an idle state. Place the device close to the connector or protected board edge when cables enter the enclosure.
This page combines device specifications, drop-in replacement options, application guidance, and design notes that support component selection and PCB implementation. Request the current quotation, lead time, and lifecycle confirmation through the Request a Quote form on this page.
Bộ thay thế dễ dàng lắp đặt cho ADM3075EYRZ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
ADM3075EWYRZ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
MAX3079EASD+T
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
XR3078XIDTR-F
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
SP3075EEN-L/TR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ADM3075EYRZ Thông số kỹ thuật
| Product Type | RS-485/RS-422 Transceiver |
| Điện áp cung cấp | 3.3 V |
| Tốc độ dữ liệu | 500 kbps |
| Duplex Mode | Half Duplex |
| Bus Loading | 1/8 Unit Load |
| Driver Count | 1 Driver |
| Receiver Count | 1 Receiver |
| ESD Protection | ±15 kV |
| Supported Standards | RS-422 and RS-485 |
| Enable Control | DE and RE |
| Receiver Fail-Safe | Yes |
| Hộp | 8-SOIC |
| Kiểu lắp đặt | Surface Mount |
| Minimum Operating Temperature | -40 °C |
| Trạng thái vòng đời | Production |
| Datasheet Revision | Rev. F |
Hướng dẫn cấu hình chân ADM3075EYRZ 8-soic
Cấu hình chân cho ADM3075EYRZ (8-soic gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADM3075EYRZ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADM3075EYRZ phù hợp cho 6 Áp dụngs: Industrial Sensor and Remote I/O Networks, Building Access Control and Security Systems, Data Acquisition and Instrumentation, Industrial Communication Gateways, Position Feedback and Motor Control Systems, Telecommunications and Network Equipment.
Industrial Sensor and Remote I/O Networks
The ADM3075EYRZ fits RS-485 networks that connect remote temperature, pressure, level, and digital I/O modules to a central controller. Its 500 kbps maximum rate is ample for periodic sensor updates and command traffic, while the 1/8-unit-load receiver helps preserve bus capacity across multiple nodes. The 3.3 V supply integrates easily with modern microcontrollers. In a multidrop installation, place termination only at the two cable endpoints and use controlled bus turnaround so the half-duplex driver releases the bus before the receiver is enabled.
Được đề xuất
Building Access Control and Security Systems
The ADM3075EYRZ is suitable for half-duplex RS-485 links between a door controller and distributed access-control readers, request-to-exit panels, or alarm modules. Its 500 kbps rate supports short bursts of credential and status traffic without occupying the cable for extended periods. The ±15 kV ESD rating adds useful protection for equipment connected through external building wiring. Firmware should enforce one active driver per bus and use the receiver fail-safe function so the controller can detect an idle or undriven line predictably.
Được đề xuất
Data Acquisition and Instrumentation
The ADM3075EYRZ can connect laboratory or industrial instrumentation over an RS-422 or RS-485 link, allowing a controller to gather measurements from distributed analog-to-digital converters and sensor interfaces. The balanced bus helps reject common-mode noise present in industrial environments, while the 500 kbps ceiling provides sufficient bandwidth for moderate-rate acquisition. Keep the transceiver close to the protected connector, provide a solid ground reference, and verify that the number of attached 1/8-unit-load receivers remains within the intended bus budget.
Được đề xuất
Industrial Communication Gateways
The ADM3075EYRZ is useful in gateways that translate between a local microcontroller bus and RS-485 equipment such as drives, meters, programmable controllers, or remote terminal blocks. Its 3.3 V operating voltage supports low-voltage system partitioning, and the half-duplex architecture reduces the number of physical bus conductors. At 500 kbps, the link handles control and status frames efficiently. The gateway should implement deterministic arbitration, timeout handling, and controlled DE/RE transitions to avoid driver contention on shared segments.
Được đề xuất
Position Feedback and Motor Control Systems
The ADM3075EYRZ can carry incremental feedback, encoder status, or supervisory commands between a motor controller and remote axis modules using an RS-485 network. The 500 kbps rate supports real-time status exchange while leaving bandwidth for diagnostic traffic. Differential signaling is beneficial in motion systems where motor currents and switching equipment can create ground-offset noise. Maintain a low-impedance reference ground, use shielded cable where appropriate, and terminate the bus at each cable end rather than at every controller.
Được đề xuất
Telecommunications and Network Equipment
The ADM3075EYRZ supports low-speed management and control interfaces in telecommunications equipment, where a 3.3 V RS-485 link can connect rack modules over a balanced cable. The 1/8-unit-load receiver allows several modules to share a segment, and the half-duplex architecture simplifies the physical layer to a single bidirectional bus pair. The 500 kbps limit is appropriate for management traffic rather than high-speed payload transport. Panel-entry protection and chassis grounding remain important because the device is a physical-layer interface, not a surge-protection network.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADM3075EYRZ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADM3075EWYRZ | MAX3079EASD+T | XR3078XIDTR-F | SP3075EEN-L/TR |
|---|---|---|---|---|---|
| Brand | Analog Devices | Analog Devices | Maxim Integrated | MaxLinear | SP Micro |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Supported Interfaces | RS-422 and RS-485 | RS-422 and RS-485 | RS-422 and RS-485 | RS-485 | RS-485 |
Bảo phân biệt quan trọng
- Direct Analog Devices family choice for existing ADM3075E designs (vsADM3075EWYRZ)
- ESD protection matches the leading bus-interface alternatives (vsMAX3079EASD+T)
- Same-footprint cross-brand sourcing option (vsSP3075EEN-L/TR)
Ghi chú thiết kế
Route the two bus conductors as a closely matched differential pair, connect the transceiver ground to the equipment ground reference, and place the device near the cable entry or protection network. Keep the DE and RE traces away from the bus traces to reduce capacitive coupling. For a half-duplex network, termination resistors belong at the two physical ends of the segment rather than beside every transceiver.
Follow the ADM3075E application guidance for supply decoupling and bus-side protection. Place the local bypass capacitor immediately across the device supply pins, with the connection loop kept short. Verify the 3.3 V rail tolerance, ground continuity, and the voltage seen by the receiver under bus-idle and bus-fault conditions before releasing the design for production.
Do not enable the driver while another node is transmitting. In firmware, disable DE, allow the transceiver propagation delay and bus release time to elapse, and then enable RE for reception. Also avoid populating termination across every node because excessive loading reduces the differential signal amplitude and can prevent reliable communication at the longest cable lengths.
Thông tin tuân thủ
The ADM3075E family is listed in production by Analog Devices. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or declaration.