Analog Devices

ADM3075EYRZ - 500 kbps RS-485 Transceiver | Analog Devices

MPN: ADM3075EYRZ ✓ 啟用中
3.3 V Vdss RS-422 and RS-485 Rds(on) 8-SOIC Package
MOQ: 1 |

ADM3075EYRZ 概覽

The Analog Devices ADM3075EYRZ is a 3.3 V, half-duplex RS-485/RS-422 transceiver rated for 500 kbps data rates and protected against ±15 kV electrostatic discharge. The device combines one driver and one receiver in an 8-pin SOIC package, supports 1/8-unit-load operation, and provides DE/RE driver-enable and receiver-enable control for shared-bus communication.

An RS-485 transceiver is the physical-layer interface between a logic-level controller and a balanced, multipoint bus. The differential signaling improves noise immunity, supports longer cable runs than single-ended interfaces, and allows multiple nodes to share a bus when their combined load permits it. The related RS-422 operating mode supports balanced point-to-point communication using the same transceiver family.

Key characteristics include a 3.3 V supply, a maximum signaling rate of 500 kbps, 1/8-unit-load bus loading, half-duplex operation, and ±15 kV ESD protection on the bus-facing pins. The DE and RE inputs allow the host to place the transmitter and receiver into high-impedance states when the controller is not actively driving or receiving data. A fail-safe receiver function helps the output remain in a defined state when the bus is idle or the driver is disabled.

The ADM3075E family is intended for industrial instrumentation, communications equipment, security systems, sensing equipment, and data-acquisition systems operating on RS-485 or RS-422 networks. Its 500 kbps capability suits moderate-speed control links, position feedback, remote sensors, industrial gateways, and supervisory communication rather than high-speed backbone traffic.

A half-duplex design requires only one pair of bus conductors, but software must control bus turnaround so that the driver does not contend with an active remote transmitter. Leave adequate termination at both physical ends of the bus and use the specified biasing arrangement to hold the differential bus at an idle state. Place the device close to the connector or protected board edge when cables enter the enclosure.

This page combines device specifications, drop-in replacement options, application guidance, and design notes that support component selection and PCB implementation. Request the current quotation, lead time, and lifecycle confirmation through the Request a Quote form on this page.

直接替換替代品,適用於 ADM3075EYRZ — 相同封裝,腳位對腳位相容。需重新設計 PCB 的不同封裝零件不列入。

ADM3075EWYRZ

✅ 直接替換
📦 8-SOIC
Same 3.3 V supply, 500 kbps data rate, 1/8-unit load, and 8-pin SOIC footprint; ordering-code grade designation differs by 0% on the listed core ratings.

📋 參考替代品(不在目錄中)

MAX3079EASD+T

✅ 直接替換
📦 8-SOIC
Matches the 3.3 V supply and 500 kbps class of the ADM3075EYRZ; verify enable logic and bus-pin capacitance, with the listed core data-rate difference at 0%.

📋 參考替代品(不在目錄中)

XR3078XIDTR-F

✅ 直接替換
📦 8-SOIC
Uses the same 8-pin SOIC footprint for a 3.3 V, 500 kbps-class bus interface; receiver threshold, enable polarity, and capacitance require comparison against the ADM3075EYRZ.

📋 參考替代品(不在目錄中)

SP3075EEN-L/TR

✅ 直接替換
📦 8-SOIC
Cross-reference information identifies consistent terminals and package with the ADM3075EYRZ; the shared 8-pin footprint requires verification of the 500 kbps rating and ±15 kV ESD level.

📋 參考替代品(不在目錄中)

ADM3075EYRZ 規格

Product Type RS-485/RS-422 Transceiver
供應電壓 3.3 V
資料速率 500 kbps
Duplex Mode Half Duplex
Bus Loading 1/8 Unit Load
Driver Count 1 Driver
Receiver Count 1 Receiver
ESD Protection ±15 kV
Supported Standards RS-422 and RS-485
Enable Control DE and RE
Receiver Fail-Safe Yes
封裝 8-SOIC
安裝類型 Surface Mount
Minimum Operating Temperature -40 °C
生命週期狀態 Production
Datasheet Revision Rev. F

ADM3075EYRZ 8-soic 腳位配置指南

ADM3075EYRZ(8-soic 封裝)的腳位配置。 腳位編號、功能與連接圖定義於製造商資料手冊中。請參閱該手冊以取得確切的封裝尺寸與焊接指引。

ADM3075EYRZ 的 8-soic 封裝腳位圖

無詳細腳位定義資料: ADM3075EYRZ.

請參閱 資料表 以查看完整腳位配置。

典型應用

ADM3075EYRZ 適用於 6 應用s: Industrial Sensor and Remote I/O Networks, Building Access Control and Security Systems, Data Acquisition and Instrumentation, Industrial Communication Gateways, Position Feedback and Motor Control Systems, Telecommunications and Network Equipment.

🏭

Industrial Sensor and Remote I/O Networks

The ADM3075EYRZ fits RS-485 networks that connect remote temperature, pressure, level, and digital I/O modules to a central controller. Its 500 kbps maximum rate is ample for periodic sensor updates and command traffic, while the 1/8-unit-load receiver helps preserve bus capacity across multiple nodes. The 3.3 V supply integrates easily with modern microcontrollers. In a multidrop installation, place termination only at the two cable endpoints and use controlled bus turnaround so the half-duplex driver releases the bus before the receiver is enabled.

🛡️

Building Access Control and Security Systems

The ADM3075EYRZ is suitable for half-duplex RS-485 links between a door controller and distributed access-control readers, request-to-exit panels, or alarm modules. Its 500 kbps rate supports short bursts of credential and status traffic without occupying the cable for extended periods. The ±15 kV ESD rating adds useful protection for equipment connected through external building wiring. Firmware should enforce one active driver per bus and use the receiver fail-safe function so the controller can detect an idle or undriven line predictably.

📟

Data Acquisition and Instrumentation

The ADM3075EYRZ can connect laboratory or industrial instrumentation over an RS-422 or RS-485 link, allowing a controller to gather measurements from distributed analog-to-digital converters and sensor interfaces. The balanced bus helps reject common-mode noise present in industrial environments, while the 500 kbps ceiling provides sufficient bandwidth for moderate-rate acquisition. Keep the transceiver close to the protected connector, provide a solid ground reference, and verify that the number of attached 1/8-unit-load receivers remains within the intended bus budget.

🌐

Industrial Communication Gateways

The ADM3075EYRZ is useful in gateways that translate between a local microcontroller bus and RS-485 equipment such as drives, meters, programmable controllers, or remote terminal blocks. Its 3.3 V operating voltage supports low-voltage system partitioning, and the half-duplex architecture reduces the number of physical bus conductors. At 500 kbps, the link handles control and status frames efficiently. The gateway should implement deterministic arbitration, timeout handling, and controlled DE/RE transitions to avoid driver contention on shared segments.

⚙️

Position Feedback and Motor Control Systems

The ADM3075EYRZ can carry incremental feedback, encoder status, or supervisory commands between a motor controller and remote axis modules using an RS-485 network. The 500 kbps rate supports real-time status exchange while leaving bandwidth for diagnostic traffic. Differential signaling is beneficial in motion systems where motor currents and switching equipment can create ground-offset noise. Maintain a low-impedance reference ground, use shielded cable where appropriate, and terminate the bus at each cable end rather than at every controller.

🖥️

Telecommunications and Network Equipment

The ADM3075EYRZ supports low-speed management and control interfaces in telecommunications equipment, where a 3.3 V RS-485 link can connect rack modules over a balanced cable. The 1/8-unit-load receiver allows several modules to share a segment, and the half-duplex architecture simplifies the physical layer to a single bidirectional bus pair. The 500 kbps limit is appropriate for management traffic rather than high-speed payload transport. Panel-entry protection and chassis grounding remain important because the device is a physical-layer interface, not a surge-protection network.

推薦產品摘要

ADM3075EWYRZ Same-family 3.3 V RS-485 transceiver 用於: Industrial Sensor and Remote I/O Networks, Building Access Control and Security Systems, Industrial Communication Gateways MAX3079EASD+T 8-SOIC transceiver alternative 用於: Industrial Sensor and Remote I/O Networks, Industrial Communication Gateways, Telecommunications and Network Equipment XR3078XIDTR-F 8-SOIC interface alternative 用於: Building Access Control and Security Systems, Position Feedback and Motor Control Systems ADS1262IPW Texas Instruments 用於: Data Acquisition and Instrumentation SP3075EEN-L/TR 8-SOIC bus-interface alternative 用於: Data Acquisition and Instrumentation, Telecommunications and Network Equipment INA240A4DR Texas Instruments 用於: Position Feedback and Motor Control Systems
What are the key specifications of ADM3075EYRZ that engineers should know?
The ADM3075EYRZ is a 3.3 V, half-duplex RS-485/RS-422 transceiver with one driver, one receiver, a maximum data rate of 500 kbps, 1/8-unit-load operation, and ±15 kV ESD protection. It is packaged in an 8-pin SOIC and provides separate DE and RE control inputs. These characteristics place it in the general-purpose industrial interface-transceiver class for moderate-speed balanced data links.
What is the operating voltage and data rate of ADM3075EYRZ?
The ADM3075EYRZ operates from a 3.3 V supply and supports data rates up to 500 kbps. Analog Devices describes the ADM3075E as a production 3.3 V, 1/8-load, ±15 kV ESD-protected RS-485/RS-422 half-duplex transceiver with DE/RE control. These are the two primary constraints when matching the device to a system clock, cable length, and bus topology.
Is ADM3075EYRZ suitable for industrial RS-485 bus applications?
Yes, the ADM3075EYRZ is suitable for industrial RS-485 networks operating at up to 500 kbps. Its 1/8-unit-load receiver, ±15 kV ESD protection, and half-duplex DE/RE architecture support multipoint bus designs for sensors, industrial controllers, remote I/O, and supervisory control links. The final design must still satisfy cable-length, grounding, and termination requirements.
Where can I download the ADM3075EYRZ datasheet PDF?
The official ADM3075E product page provides the manufacturer datasheet, product-selection table, documentation, and hardware ecosystem information. Use the Analog Devices ADM3075E page to obtain the current Rev. F data sheet and application guidance. The pin-description table in that document should be used when assigning PCB tracks and checking signal names against the selected package variant.
Where can I find the ADM3075EYRZ pinout?
The ADM3075EYRZ uses an 8-pin SOIC, and its complete pin-description table is contained in the ADM3075E manufacturer datasheet. Use that table when mapping the receiver output, receiver-enable input, driver-enable input, driver input, ground, bus pins, and supply connection. Confirm the selected ordering code against the ordering guide before releasing artwork to fabrication.
What can replace ADM3075EYRZ as a drop-in part?
The ADM3075EWYRZ is a closely related Analog Devices variant in the same 8-SOIC format, while MAX3079EASD+T, XR3078XIDTR-F, and SP3075EEN-L/TR are identified as same-package alternatives. Pin compatibility must still be confirmed from each candidate's datasheet, particularly driver-enable, receiver-enable, and supply connections, before treating any replacement as production-approved.
Is ADM3075EYRZ the same as MAX3079EASD+T?
The ADM3075EYRZ and MAX3079EASD+T are both 8-pin RS-485/RS-422 interface solutions operating from 3.3 V with 500 kbps-class signaling and ±15 kV ESD protection. Their key ratings are therefore closely aligned, but a drop-in decision still requires comparison of DE/RE truth tables, receiver fail-safe behavior, bus-pin capacitance, and absolute maximum ratings. Review both datasheets before substitution.
When should I choose ADM3075EYRZ over MAX3079EASD+T?
Choose the ADM3075EYRZ when its Analog Devices documentation, qualification record, and product support align with your qualification process. MAX3079EASD+T is attractive when its pin definition and electrical ratings are fully verified against the existing PCB. Neither device should be selected solely from the shared 3.3 V supply, 500 kbps rate, and 8-SOIC package.
When should I choose ADM3075EYRZ over XR3078XIDTR-F?
Choose the ADM3075EYRZ when you prioritize a 3.3 V, half-duplex, 1/8-load transceiver with 500 kbps operation and ±15 kV ESD protection documented in the ADM3075E family. Choose XR3078XIDTR-F when its verified electrical characteristics provide a better system match, such as an improved receiver threshold or bus-drive behavior. The existing footprint and logic-level control definitions must match in either case.
Can SP3075EEN-L/TR replace ADM3075EYRZ on an existing PCB?
SP3075EEN-L/TR is identified as an alternative with consistent terminals and package, making it a candidate for an existing 8-SOIC RS-485 design. Confirm pin-by-pin alignment and compare supply voltage, maximum data rate, unit load, ESD rating, enable logic, and receiver fail-safe behavior. A layout change should never be required without an explicit engineering review.
What is the best Maxim Integrated equivalent for ADM3075EYRZ?
MAX3079EASD+T is the closest Maxim Integrated alternative identified for the ADM3075EYRZ because both are 3.3 V, 8-SOIC, high-speed half-duplex RS-485/RS-422 transceivers with 500 kbps-class operation and ±15 kV ESD protection. Verify the pin mapping, DE/RE polarity, receiver-output behavior, and bus capacitance in the manufacturer datasheet before approving the substitution.
How much bus loading does ADM3075EYRZ add to an RS-485 network?
Each ADM3075EYRZ receiver presents a 1/8-unit load to the bus. The allowable number of receivers therefore depends on the bus standard, cable length, data rate, termination arrangement, and the combined loads of other connected devices. Use the unit-load calculation in the ADM3075E datasheet and avoid adding transceivers solely for parallel processing unless the bus loading budget permits it.
Does ADM3075EYRZ need external termination and fail-safe biasing?
The ADM3075EYRZ requires the external network components specified for the chosen bus topology. Install termination resistors at the two physical ends of a long RS-485 cable rather than at every node, and use the recommended bias arrangement to establish a defined differential idle state. The exact resistor values and placement should follow the manufacturer application guidance and your cable length.
Where can I buy ADM3075EYRZ and check its current lead time?
Use the Request a Quote form on this page to request the current ADM3075EYRZ quotation, stock position, lead time, and authorized-channel options. The form is the appropriate route for commercial confirmation because pricing and availability can change with market conditions, production allocation, and package demand. Include your target quantity and required ship date in the request.
What is the current price of ADM3075EYRZ?
The current commercial terms for ADM3075EYRZ are provided through the Request a Quote form on this page. The form supports quantity-specific quotation, current availability, and lead-time confirmation for the exact 8-SOIC ordering code. Share the required shipment date and target quantity so the response can reflect the correct production and logistics position.
Is ADM3075EYRZ currently in stock and what is its lead time?
Stock and lead time for the ADM3075EYRZ should be confirmed through the Request a Quote form on this page. Because component inventory and factory lead times fluctuate, request the quantity, package code, and required delivery date with your inquiry. The manufacturer lists the ADM3075E family as being in production, which supports ongoing sourcing planning.

工程參考資料,適用於 ADM3075EYRZ — 比較、設計指引及合規資訊。

選型指南

Choose the ADM3075EYRZ when your system requires a 3.3 V, half-duplex RS-485/RS-422 transceiver with 500 kbps operation, 1/8-unit-load sensitivity, and ±15 kV ESD protection in an 8-SOIC package. It is a natural selection when you want continuity with the Analog Devices ADM3075E family and controlled DE/RE bus management. Choose ADM3075EWYRZ when the related grade designation better fits your qualification plan. Consider MAX3079EASD+T when an alternative manufacturer provides supply-chain or qualification advantages, and confirm pin definitions, enable polarity, bus capacitance, and fail-safe behavior. XR3078XIDTR-F and SP3075EEN-L/TR are additional 8-SOIC candidates, but their enable logic, receiver thresholds, and detailed absolute-maximum ratings require direct comparison with the ADM3075E datasheet. In every case, validate cable length, node count, termination, grounding, and bus-turnaround timing in the final system.

與替代品比較

參數 本產品 ADM3075EWYRZ MAX3079EASD+T XR3078XIDTR-F SP3075EEN-L/TR
Brand Analog Devices Analog Devices Maxim Integrated MaxLinear SP Micro
Package 8-SOIC 8-SOIC 8-SOIC 8-SOIC 8-SOIC
Supported Interfaces RS-422 and RS-485 RS-422 and RS-485 RS-422 and RS-485 RS-485 RS-485

主要差異化特點

  • Direct Analog Devices family choice for existing ADM3075E designs (對比ADM3075EWYRZ)
  • ESD protection matches the leading bus-interface alternatives (對比MAX3079EASD+T)
  • Same-footprint cross-brand sourcing option (對比SP3075EEN-L/TR)

設計說明

Route the two bus conductors as a closely matched differential pair, connect the transceiver ground to the equipment ground reference, and place the device near the cable entry or protection network. Keep the DE and RE traces away from the bus traces to reduce capacitive coupling. For a half-duplex network, termination resistors belong at the two physical ends of the segment rather than beside every transceiver.

Follow the ADM3075E application guidance for supply decoupling and bus-side protection. Place the local bypass capacitor immediately across the device supply pins, with the connection loop kept short. Verify the 3.3 V rail tolerance, ground continuity, and the voltage seen by the receiver under bus-idle and bus-fault conditions before releasing the design for production.

Do not enable the driver while another node is transmitting. In firmware, disable DE, allow the transceiver propagation delay and bus release time to elapse, and then enable RE for reception. Also avoid populating termination across every node because excessive loading reduces the differential signal amplitude and can prevent reliable communication at the longest cable lengths.

合規資訊

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
無鉛
Unknown
無鹵
Unknown
衝突礦產
Unknown

The ADM3075E family is listed in production by Analog Devices. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from the current manufacturer product documentation or declaration.

資料驗證日期: 2026-11-19 — 資料由 XAIPART 元件工程團隊驗證及整理

相關搜尋

ADM3075EYRZ datasheet ADM3075EYRZ pinout ADM3075EYRZ 8-SOIC pinout ADM3075E 500 kbps RS-485 ADM3075EYRZ price ADM3075EYRZ stock Analog Devices ADM3075EYRZ ADM3075EYRZ drop-in replacement ADM3075EYRZ vs MAX3079EASD+T ADM3075EYRZ vs SP3075EEN-L/TR ADM3075EYRZ equivalent transceiver ADM3075EYRZ RS-485 application circuit

相關元件與詞彙

Analog Devices ADM3075EYRZ ADM3075EWYRZ MAX3079EASD+T XR3078XIDTR-F SP3075EEN-L/TR RS-485 RS-422 transceiver half-duplex transceiver differential signaling multipoint bus 1/8 unit load 500 kbps 3.3 V DE and RE control fail-safe receiver ±15 kV ESD protection 8-SOIC SOIC package family surface-mount package industrial instrumentation building access control data acquisition system industrial communication gateway
快速報價 RFQ
請填寫完整詳細資料 — 我們的業務團隊將於 24 小時內回覆
料號 製造商 封裝 QTY 目標價格 小計
✓
報價已提交!

我們將於 24 小時內回覆您的電子郵件

1
詢價已提交
2
已收到報價
3
已下單
4
付款
5
已出貨
6
已送達
檢視詢價單詳情