ADS7800JP - 12-Bit 3us SAR ADC | Texas Instruments
MPN: ADS7800JP ✓ Hoạt độngADS7800JP Tóm tắt
An ADC is a data-acquisition IC that converts a continuously varying analog voltage into a digital code for processing, measurement, or control. The ADS7800 belongs to the SAR ADC hierarchy, where a successive-approximation conversion compares the sampled input with an internal reference through successive binary trials. Relative to flash and pipeline ADCs, the SAR architecture combines modest resolution and conversion speed with relatively simple control logic and low cost, making it suitable for industrial instrumentation and embedded measurement systems.
The principal features include 12-bit resolution, one analog input channel, and a stated 3 microsecond conversion rate. Internal sample-and-hold, reference, clock, and microprocessor interface blocks reduce the number of external support components. Three-state output drivers allow the digital bus to be placed in a high-impedance state, supporting shared-bus or microprocessor-controlled acquisition arrangements. The converter is available in performance grades covering 0°C to +70°C and -40°C to +85°C operating ranges.
The ADS7800 uses CMOS structures for its sampling and conversion circuitry. During acquisition, the sample-and-hold network presents a stable voltage to the internal SAR core; after the falling edge of the conversion signal, successive approximation decisions establish the digital result. Its parallel microprocessor interface provides direct binary-code access, while the three-state drivers permit controlled connection to compatible data buses. The -12 V or -15 V negative supply expands the usable bipolar input range beyond a conventional single-supply ADC.
Typical uses include industrial process-control loops, transducer instrumentation, data acquisition modules, digital voltmeters, laboratory measurement equipment, and embedded control systems. The 3 microsecond conversion time supports updating measurement loops without the pipeline latency associated with faster high-resolution converters. Designers should preserve the input range, supply sequencing, and logic-level requirements of the selected device grade.
A key implementation consideration is the ADS7800's unusual combination of +5 V, -12 V or -15 V, and analog-supply connections. Reference and analog-input bypass capacitors should be placed close to their associated pins, while the digital interface must not drive the three-state outputs during acquisition. The 24-pin DIP footprint also requires adequate spacing for through-hole assembly and appropriate clearances around sensitive analog pins.
This page combines the manufacturer product information with practical engineering guidance for signal conditioning, supply implementation, digital interfacing, and component selection. It also identifies same-family drop-in options and highlights the operating-temperature differences that matter when planning industrial or extended-temperature equipment.
Bộ thay thế dễ dàng lắp đặt cho ADS7800JP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADS7800JP (cùng hình factor và footprint) — khác nhau ở Architecture, Input Type, Resolution.
ADS7800Y
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADS7800YP
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADS7800JP Tỷ lệ tối đa & tính chất điện
| Độ phân giải | 12 bit |
| Conversion Time | 3 us |
| Architecture | Successive approximation (SAR) |
| Analog Input Channels | 1 channel |
| Input Type | Single-ended analog input |
| Positive Supply Voltage | +5 V |
| Negative Supply Voltage | -12 V or -15 V |
| Hộp | 24-pin plastic DIP |
| Sample-and-Hold Circuit | Internal |
| Reference | Internal |
| Clock | Internal |
| Digital Interface | Microprocessor-compatible parallel interface |
| Output Driver | Three-state output drivers |
| Operating Temperature Grade 1 | 0°C to +70°C |
| Operating Temperature Grade 2 | -40°C to +85°C |
Hướng dẫn cấu hình chân ADS7800JP 24-pin plastic dip
Cấu hình chân cho ADS7800JP (24-pin plastic dip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho ADS7800JP.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADS7800JP phù hợp cho 6 Áp dụngs: Industrial Process Measurement, Digital Voltmeter and Panel Meter, Transducer Data Acquisition, Embedded Control System, Laboratory Signal Acquisition, Power and Equipment Monitoring.
Industrial Process Measurement
The ADS7800JP fits single-channel industrial process measurement because it combines 12-bit resolution with a 3 microsecond conversion time in a 24-pin plastic DIP package. Place it behind a protected analog front end that scales a pressure, temperature, or level transducer into the converter's input range. The fast conversion allows the controller to refresh its process variable without requiring a high-order pipeline ADC. Its -40°C to +85°C operating grade supports equipment installed in industrial environments, although the +5 V and -12 V or -15 V supply architecture requires careful rail planning.
Được đề xuất
Digital Voltmeter and Panel Meter
The ADS7800JP can digitize a scaled dc voltage for a digital voltmeter or panel meter. Its 12-bit conversion result provides 4096 code levels, while the 3 microsecond conversion time supports responsive meter updates. The analog front end should perform attenuation, filtering, and input protection before driving the single ADC input. Because the ADS7800JP includes an internal sample-and-hold circuit, reference, and clock, the system can remain compact, while the parallel interface and three-state outputs support direct connection to a microprocessor or display controller.
Được đề xuất
Transducer Data Acquisition
For pressure, load-cell, or resistance-based transducer acquisition, the ADS7800JP provides a single 12-bit measurement channel with a 3 microsecond conversion time. Use an instrumentation front end to convert the transducer signal into an analog voltage within the converter's supported input range, then add filtering close to the ADC input. The integrated sample-and-hold and reference blocks reduce external circuitry, while the -40°C to +85°C grade supports wide-ranging industrial equipment. Calibration systematics should be evaluated in software because converter resolution does not remove errors contributed by the front end, reference network, or sensor.
Được đề xuất
Embedded Control System
The ADS7800JP is appropriate for embedded controllers that need periodic analog measurements without multiplexing multiple channels through one converter. Its 3 microsecond conversion time allows rapid sampling relative to many control loops, and the microprocessor-compatible parallel interface provides direct access to the 12-bit code. The host controller must manage the conversion-control handshake and release the three-state outputs at the correct time. Designers should allocate layout space for the through-hole DIP package and isolate the analog input and reference paths from digital return currents and switching regulators.
Được đề xuất
Laboratory Signal Acquisition
The ADS7800JP can serve as the conversion element in a laboratory data-acquisition module when the input bandwidth and resolution match the measurement. Its 12-bit resolution and 3 microsecond conversion time are useful for slowly varying or periodically sampled waveforms, but the analog input bandwidth and acquisition timing must be checked against the signal of interest. Use shielded interconnections, stable reference bypassing, and careful grounding to reduce noise pickup. The 24-pin DIP construction also simplifies breadboard and prototype assembly, making it useful for repeatable instrument development before converting to a smaller production package.
Được đề xuất
Power and Equipment Monitoring
The ADS7800JP is suitable for monitoring a slowly changing power-system or equipment parameter when the measured quantity is conditioned into the ADC input range. A 3 microsecond conversion time is substantially quicker than most mechanical monitoring cycles, allowing multiple readings to be averaged or transferred to a controller. The single-channel architecture simplifies signal routing but requires channel selection or multiple converter instances when several variables must be sampled simultaneously. Ensure the input protection network can withstand transients, and account for the device's -12 V or -15 V supply requirement when sizing the system power rails.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADS7800JP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADS7800Y | ADS7800YP |
|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 24-pin plastic DIP | 24-pin plastic DIP | 24-pin plastic DIP |
| Resolution | 12 bit | 12 bit | 12 bit |
| Conversion Time | 3 us | 3 us | 3 us |
| Architecture | Successive approximation | Successive approximation | Successive approximation |
| Analog Input Channels | 1 channel | 1 channel | 1 channel |
| Positive Supply | +5 V | +5 V | +5 V |
| Negative Supply | -12 V or -15 V | -12 V or -15 V | -12 V or -15 V |
| Operating Temperature Range | -40°C to +85°C | 0°C to +70°C | -40°C to +85°C |
| Digital Output | Microprocessor-compatible parallel interface with three-state drivers | Microprocessor-compatible parallel interface with three-state drivers | Microprocessor-compatible parallel interface with three-state drivers |
Bảo phân biệt quan trọng
- Broader upper temperature rating than ADS7800Y (vsADS7800Y)
- Matches the extended-temperature performance of ADS7800YP (vsADS7800YP)
- Integrated converter functions reduce external support circuitry (vsADS7800Y)
Ghi chú thiết kế
Plan the ADS7800JP power architecture around +5 V and either -12 V or -15 V rather than treating it as a single-supply converter. Bypass the positive and negative rails near the package, maintain the supply magnitudes specified in the Texas Instruments datasheet, and verify startup sequencing before enabling the analog input. A negative rail generated by a switching converter should be filtered to prevent converter ripple from appearing directly at the ADC input.
Use the manufacturer's pin-configuration drawing to place the 24-pin DIP correctly, and route the analog input directly to its assigned pin with a short trace. Place input filtering, reference bypass, and supply-decoupling capacitors close to the associated device pins. Keep switching-regulator outputs, inductors, and high-current return paths away from the analog input; their radiated and conducted noise can dominate the performance of a 12-bit measurement channel.
Do not assume that a higher-resolution replacement is automatically interchangeable. Before fitting ADS7800Y or ADS7800YP, confirm the plastic DIP footprint, pin names, +5 V and negative-supply requirements, 12-bit output coding, acquisition timing, and three-state bus behavior. In particular, ADS7800Y has a 0°C to +70°C range, so using it in an enclosure expected to exceed +70°C creates a thermal-qualification failure risk.
Thông tin tuân thủ
The ADS7800 is an industrial analog converter rather than an AEC-Q100-qualified automotive device. Specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements were not identified.