ADV7401KSTZ-140 - 10-Bit Video Decoder | Analog Devices
MPN: ADV7401KSTZ-140 ✓ Hoạt độngADV7401KSTZ-140 Tóm tắt
A video decoder is an interface IC that converts legacy analog television waveforms into digital pixels suitable for capture, scaling, processing, encoding, or display. Within the broader semiconductor hierarchy, the ADV7401 belongs to video processing ICs, interface ICs, and multimedia signal-processing semiconductors. Its integrated analog front end and digital output reduce the need for separate decoders when equipment must accept multiple regional television standards.
The ADV7401 supports 10-bit digitization for PAL, NTSC, and SECAM, with composite and S-video inputs identified in the manufacturer product information. Serial digital output follows the ITU-R BT.656 interface format. The device also incorporates on-screen display and teletext support, as identified for the ADV7401KSTZ-140, along with RGB graphics digitization. These features make it applicable to broadcast equipment, video capture systems, industrial monitoring panels, and legacy-source conversion equipment.
The -140 orderable variant uses a 100-lead, 14 mm by 14 mm low-profile flat package and is specified for an industrial temperature range of 0°C to 70°C. The 100-pin interface exposes the analog video inputs, digital processing connections, control signals, synchronization outputs, and supply rails. That extensive mixed-signal pinout requires a carefully partitioned PCB with short analog paths, controlled return currents, and separate routing for digital output and clock signals.
Typical designs place the ADV7401 between an analog video connector and an FPGA, DSP, image processor, or digital video encoder. In a PAL/NTSC capture system, the decoder digitizes the incoming composite signal and presents synchronized 10-bit pixels over ITU-R BT.656 for downstream processing. In broadcast or professional monitoring equipment, its multistandard decoding, OSD, and teletext capabilities reduce the number of separate video subsystem blocks while preserving a common digital processing interface.
The primary design consideration is mixed-signal implementation. Route composite and S-video inputs away from high-speed digital clocks, use an uninterrupted ground plane, place bypass capacitors at the supply pins, and follow the pin-description table in the manufacturer datasheet when assigning connector and processor connections. Confirm supported resolution, synchronization mode, and output timing against the system video standard before releasing the PCB layout.
This product page consolidates the multiformat decoding capability, package details, practical interface guidance, qualified drop-in comparisons, and sourcing information needed to evaluate the ADV7401KSTZ-140 before integrating it into an SDTV, HDTV, broadcast, capture, or industrial video design.
Bộ thay thế dễ dàng lắp đặt cho ADV7401KSTZ-140 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ADV7401KSTZ-140 (cùng hình factor và footprint) — khác nhau ở Package.
ADV7401KSTZ-100
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADV7401KSTZ-110
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADV7401KSTZ-120
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADV7401KSTZ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ADV7403KSTZ-140
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADV7400AKSTZ-80
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ADV7401KSTZ-140 Thông số kỹ thuật
| Product Type | 10-bit multiformat SDTV/HDTV video decoder and RGB graphics digitizer |
| Supported Analog Standards | PAL, NTSC, SECAM |
| Supported Analog Inputs | Composite and S-video |
| Digital Output Format | Serial ITU-R BT.656 |
| Digitization Resolution | 10 bit |
| Analog Supply Voltage | 3.3 V |
| Digital Supply Voltage | 1.8 V |
| Graphics Processing | RGB graphics digitization |
| On-Screen Display Support | Supported |
| Teletext Support | Supported |
| Hộp | 100-lead LQFP, 14 mm x 14 mm |
| Khoảng nhiệt độ hoạt động | 0°C to 70°C |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân ADV7401KSTZ-140 100-lead lqfp, 14 mm x 14 mm
Cấu hình chân cho ADV7401KSTZ-140 (100-lead lqfp, 14 mm x 14 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho ADV7401KSTZ-140.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ADV7401KSTZ-140 phù hợp cho 6 Áp dụngs: Multiformat Broadcast Video Capture, Industrial Video Inspection Systems, Legacy AV Signal Conversion, Security and CCTV Video Interface, Video Test and Measurement Equipment, Professional Video Monitoring and OSD.
Multiformat Broadcast Video Capture
The ADV7401KSTZ-140 fits broadcast capture equipment that must accept PAL, NTSC, or SECAM material through composite or S-video connections. Its 10-bit decoder converts the analog source into ITU-R BT.656 digital pixels for an FPGA, DSP, image processor, or encoder, reducing the need for separate format-specific decoders. Place the device near the input connector, route the analog signals away from processor clocks, and use the 1.8 V digital and 3.3 V analog rails with local bypass capacitors. The principal benefit is one integrated decoder path for multiple regional video standards, while the designer must still confirm supported resolution, timing, and chroma behavior for each format.
Được đề xuất
Industrial Video Inspection Systems
The ADV7401KSTZ-140 is suitable for industrial inspection and monitoring equipment that receives legacy composite or S-video camera signals and needs a digital processing path. Its 0°C to 70°C industrial temperature range, multiformat decoding, OSD capability, and 10-bit digitization support systems that combine captured imagery with overlays or graphics. The decoder can feed a processor that performs edge detection, measurement, or machine-vision analysis. Keep analog traces short, preserve a continuous ground reference, and isolate high-energy switching nodes from the input section. The 100-lead LQFP footprint provides the required mixed-signal connectivity but requires deliberate partition of analog, digital, clock, and supply routes.
Được đề xuất
Legacy AV Signal Conversion
The ADV7401KSTZ-140 can form the input stage of a legacy AV converter that accepts PAL, NTSC, or SECAM equipment and exports standardized digital video. Its composite and S-video inputs support equipment ranging from professional source converters to menu-generation and service systems, while ITU-R BT.656 output connects cleanly to digital processing logic. OSD and teletext support add value in professional monitoring and broadcast-adjacent products. Because the chip combines analog decoding and digital signaling, the converter PCB should separate video connectors, grounding, and switching supplies from high-speed digital routing. Use the family application circuit as the basis for impedance, termination, filtering, and supply-decoupling implementation.
Được đề xuất
Security and CCTV Video Interface
The ADV7401KSTZ-140 is applicable to legacy security and CCTV equipment that receives analog camera video and needs to convert it for digital recording or transmission. The PAL/NTSC/SECAM compatibility covers international analog camera standards, while the 10-bit ITU-R BT.656 output provides a deterministic digital interface for an image processor or encoder. OSD support can add camera identification or status graphics without a separate overlay generator. The design must maintain low-noise grounding around the analog section, use filtering recommended by Analog Devices, and avoid routing composite signals beneath switching regulators and high-speed memories. Confirm the camera format, synchronization scheme, chroma standard, and environmental temperature before selecting the device.
Được đề xuất
Video Test and Measurement Equipment
The ADV7401KSTZ-140 supports multiformat video test equipment where PAL, NTSC, and SECAM composite or S-video sources must be digitized for measurement. The 10-bit decoder and ITU-R BT.656 output allow the captured image to be analyzed by an FPGA, DSP, or graphics controller, while OSD and teletext functions assist in identifying channels and displaying menus. Design the input path with short connectors and controlled grounding to preserve measurement quality, and provide clean 1.8 V and 3.3 V supplies with local decoupling. Instrument-grade results also depend on clock jitter, analog filtering, synchronization accuracy, and external calibration, which should be evaluated together with the decoder rather than inferred from its nominal bit depth.
Được đề xuất
Professional Video Monitoring and OSD
The ADV7401KSTZ-140 fits professional monitoring designs that decode multiple analog standards and need overlays, graphics, or teletext-related functions. Its support for RGB graphics digitization, on-screen display, and teletext allows a single decoder-related block to serve both picture acquisition and information display. The resulting ITU-R BT.656 stream can be routed to a processor or video encoder for display. Because the 100-lead LQFP contains both analog and digital interfaces, layout quality strongly affects cursor visibility and picture stability. Keep the analog video section away from switching nodes, maintain short return paths, and use controlled clock routing. Firmware must also be adapted to the selected synchronization, OSD, and teletext configuration.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ADV7401KSTZ-140 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ADV7401KSTZ-100 | ADV7401KSTZ-110 | ADV7401KSTZ-120 | ADV7401KSTZ | ADV7403KSTZ-140 | ADV7400AKSTZ-80 |
|---|---|---|---|---|---|---|---|
| Package | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) | 100-lead LQFP (14 mm x 14 mm) |
| Brand | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices | Analog Devices |
| Device Family | ADV7401 | ADV7401 | ADV7401 | ADV7401 | ADV7401 | ADV7403 | ADV7400 |
| Ordering Suffix | -140 | -100 | -110 | -120 | No grade suffix | -140 | -80 |
Bảo phân biệt quan trọng
- Integrated multistandard decoding with OSD and teletext (vsADV7403KSTZ-140)
- Target -140 grade with documented industrial temperature range (vsADV7400AKSTZ-80)
- Defined 1.8 V digital and 3.3 V analog supply arrangement (vsADV7401KSTZ-120)
Ghi chú thiết kế
Separate the analog video section from digital processing and clock routing. Keep composite and S-video traces short, avoid running them beneath switching nodes or high-speed buses, and provide a continuous ground reference beneath the decoder. The 3.3 V analog supply and 1.8 V digital supply should each be decoupled locally at their associated pins, with return-current paths arranged to minimize coupling into the video input.
Use the manufacturer’s recommended application circuit as the basis for connector protection, input filtering, supply bypassing, and digital output routing. Place input protection and filtering components close to the video connector, and place bypass capacitors close to the corresponding ADV7401KSTZ-140 supply pins. Maintain the package’s exposed thermal and ground-connection requirements and follow the land pattern in the package drawing before releasing artwork.
Treat the 10-bit ITU-R BT.656 output as a synchronous digital interface whose signal integrity depends on clock and data timing. Route clock and data using a topology consistent with the destination device, keep the clock away from analog inputs, and verify setup and hold requirements with the actual receiver. External resistors or capacitors should be added only where required by the manufacturer’s reference design or validated timing analysis.
Do not select a decoder solely by its 10-bit nominal resolution. Confirm PAL, NTSC, and SECAM support, chroma behavior, synchronization mode, supported picture format, OSD behavior, and clock configuration for the actual signal source. Also verify that the selected ADV7401 grade matches the required temperature range. A suffix substitution can alter ordering-grade behavior even when the package and primary decoder class remain the same.
Thông tin tuân thủ
The product is specified for industrial temperature operation. A distributor listing references RoHS, but a definitive compliance declaration was not established, so all compliance states remain unknown.