ATSAML11E15A-MF - 32MHz Secure Arm Cortex-M23 MCU | Microchip
MPN: ATSAML11E15A-MF ✓ Hoạt độngATSAML11E15A-MF Tóm tắt
A microcontroller is a programmable semiconductor that integrates a processor core, memory, and peripherals into one device. The Cortex-M23 architecture belongs to the Arm Cortex-M product family, which is designed for compact embedded control systems. In the broader hierarchy, this MCU combines a 32-bit RISC processor, nonvolatile program memory, volatile data memory, and communication peripherals in a single low-power device suitable for secure edge and IoT equipment.
Key characteristics include a 32 MHz maximum operating frequency, 32 KB of flash, 8 KB of SRAM, and a 1.62 V to 3.63 V supply range. According to the Microchip product page, active consumption is below 25 uA/MHz and sleep consumption is below 100 nA. These figures support low-duty-cycle designs in which the controller remains asleep between brief measurement, control, or communications activities.
The security architecture is central to the device. Arm TrustZone separates secure and nonsecure software domains, while chip-level security, secure key storage, and tamper resistance help protect credentials and sensitive operations. These functions make the Cortex-M23 platform appropriate for authenticated devices that must establish trust before exchanging data with a host, service, or connected sensor network.
Typical uses include low-power IoT sensor nodes, industrial condition-monitoring equipment, secure access-control peripherals, battery-powered data loggers, and compact security appliances. The 32 KB flash capacity suits moderate firmware images, while the 32-VQFN package supports space-constrained board layouts. The 1.62 V to 3.63 V operating range also allows the MCU to operate across common low-voltage embedded supply rails.
Designers should verify the complete pin assignment, exposed-pad connection, decoupling requirements, and supported peripheral mix against the manufacturer datasheet before layout release. The small 5 x 5 mm package benefits from careful escape routing, while firmware migration should account for the TrustZone-aware Cortex-M23 architecture and the device's security configuration.
This page combines manufacturer specifications, package and ordering information, practical design guidance, and pin-compatible alternatives to support component selection, PCB planning, firmware review, and sourcing decisions.
Bộ thay thế dễ dàng lắp đặt cho ATSAML11E15A-MF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAML11E15A-MF (cùng hình factor và footprint) — khác nhau ở Active Current, Package, Sleep Current, Core Architecture, Operating Temperature Range.
ATSAML11E15A-MFKPH
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
ATSAML11E15A-MUT
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATSAML11E16A-MF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATSAML11E17A-MF
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
ATSAML11E14A-MF
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →ATSAML11E15A-MF Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M23 microcontroller |
| Processor Core | Arm Cortex-M23 |
| Maximum CPU Frequency | 32 MHz |
| Flash Memory | 32 KB (32K x 8) |
| SRAM | 8 KB |
| Data EEPROM | 2 KB |
| Supply Voltage Range | 1.62 V to 3.63 V |
| Khoảng nhiệt độ hoạt động | -40 °C to +125 °C |
| Hộp | 32-VQFN, 5 x 5 mm |
| Terminal Count | 32 terminals |
| Kiểu lắp đặt | No-lead surface mount |
| Active Current | Less than 25 uA/MHz |
| Sleep Current | Less than 100 nA |
| Security Architecture | Arm TrustZone, secure key storage, chip-level tamper resistance |
| Communication Interfaces | I2C, SPI, UART |
| Temperature Grade | Automotive, -40 °C to +125 °C |
| Trạng thái RoHS | unknown |
| REACH Status | unknown |
| AEC-Q100 Qualification | unknown |
Hướng dẫn cấu hình chân ATSAML11E15A-MF 32-vqfn, 5 x 5 mm
Cấu hình chân cho ATSAML11E15A-MF (32-vqfn, 5 x 5 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATSAML11E15A-MF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATSAML11E15A-MF phù hợp cho 6 Áp dụngs: Low-Power IoT Sensor Node, Secure Industrial Condition Monitoring, Battery-Powered Data Logger, Secure Access-Control Peripheral, Connected Security Appliance, Portable Diagnostic Instrument.
Low-Power IoT Sensor Node
The ATSAML11E15A-MF fits compact IoT sensor nodes that periodically read environmental data and transmit results over I2C, SPI, or UART. Its Arm Cortex-M23 core runs at up to 32 MHz, providing enough processing performance for protocol handling and local logic, while the sleep current below 100 nA supports long intervals between activity. The 32 KB flash and 8 KB SRAM provide useful code and working-memory margins. Secure key storage and TrustZone are valuable when the node must protect credentials used during authenticated communication.
Được đề xuất
Secure Industrial Condition Monitoring
The ATSAML11E15A-MF supports industrial monitoring equipment that collects sensor information, runs local filtering, and reports machine status. Its 1.62 V to 3.63 V operating range accommodates common low-voltage rails, while the -40 °C to +125 °C rating supports wide environmental conditions. The 32 MHz Cortex-M23 core can service multiple serial interfaces, and 8 KB of SRAM provides room for buffers. TrustZone separation can isolate supervisory or diagnostic code from security-sensitive operations.
Được đề xuất
Battery-Powered Data Logger
A battery-powered data logger can use the ATSAML11E15A-MF to sample sensors, timestamp events, and store information in nonvolatile memory. The MCU's sleep consumption below 100 nA is central to minimizing standby drain, while active consumption below 25 uA/MHz helps control the brief processing intervals. The 32 KB flash can hold the operating firmware and logging configuration. A 32-VQFN 5 x 5 mm package preserves board area, although thermal and decoupling layout remain important.
Được đề xuất
Secure Access-Control Peripheral
The ATSAML11E15A-MF is suitable for electronic locks, credential readers, and access-control terminals that must process local authentication logic securely. The Cortex-M23 architecture provides Arm TrustZone support, while secure key storage and tamper-resistance features help protect sensitive device operations. Its I2C, SPI, and UART interfaces support readers, secure elements, displays, and host processors. The 32 MHz operating speed and 32 KB flash are appropriate for compact firmware that does not require a large application partition.
Được đề xuất
Connected Security Appliance
The ATSAML11E15A-MF can serve as the control processor in a compact network-security or cryptographic accessory. TrustZone provides a hardware-assisted boundary between privileged and nonprivileged software, while secure key storage supports protection of locally managed credentials. The 32-bit Cortex-M23 core operates at up to 32 MHz for protocol processing, and the available UART, SPI, and I2C interfaces allow connection to sensors, network interfaces, or secure elements. The small VQFN package supports compact enclosure designs.
Được đề xuất
Portable Diagnostic Instrument
The ATSAML11E15A-MF is useful in portable diagnostic and measurement instruments where a local processor must coordinate sensors, communications, and a user interface. Its 32 MHz Cortex-M23 core handles protocol conversion and real-time control, while 8 KB of SRAM supports transient measurement data and communication buffers. The 1.62 V to 3.63 V supply range enables operation from compact battery-derived rails. The automotive temperature rating supports harsh environments, although each product still requires its own qualification review.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAML11E15A-MF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAML11E15A-MFKPH | ATSAML11E15A-MUT | ATSAML11E16A-MF | ATSAML11E17A-MF | ATSAML11E14A-MF |
|---|---|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) | 32-VQFN (5x5) |
| Processor Core | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 | Arm Cortex-M23 |
| Maximum CPU Frequency | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz | 32 MHz |
| Flash Memory | 32 KB | 32 KB | 32 KB | 48 KB | 64 KB | 16 KB |
Bảo phân biệt quan trọng
- Higher flash capacity than the 16 KB family member (vsATSAML11E14A-MF)
- Documented 32 MHz performance with 8 KB SRAM (vsATSAML11E15A-MFKPH)
- Low-power operation for duty-cycled embedded systems (vsATSAML11E16A-MF)
Ghi chú thiết kế
Reserve the exposed pad as a low-impedance ground connection and follow the manufacturer land pattern for the 32-VQFN 5 x 5 mm package. Place input and output decoupling capacitors close to their designated supply pins, keeping high-current return paths short. Because the package has no external leads, assembly inspection should include exposed-pad solder fill and continuity checks.
Design the 1.62 V to 3.63 V supply path so it remains within the operating range during startup, sleep transitions, and maximum processing load. Avoid voltage overshoot above the device limit when peripheral rails share the source. Verify brownout behavior and power-sequencing requirements in firmware because reset conditions during rail transitions can create unintended peripheral activity.
Keep I2C, SPI, and UART routing away from noisy switching nodes, inductors, and high-current return paths. Use continuous ground references beneath serial interfaces and terminate high-speed or long SPI routes according to the clock rate and peripheral characteristics. Firmware should configure pins for their final function only after the relevant clocks and rails are stable.
Do not assume that every ATSAML11 ordering code is interchangeable merely because its package matches. Confirm the temperature grade, qualification, pin assignments, exposed-pad treatment, and firmware support before substitution. ATSAML11E14A-MF has half the flash of the target and can fail when the complete firmware image, update payload, or boot loader exceeds 16 KB.
Thông tin tuân thủ
The device is identified with an automotive temperature grade, but no explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statement is present in the cited product information.