ATMEGA169A-MU - 16MHz 8-Bit AVR MCU 64-QFN | Microchip
MPN: ATMEGA169A-MU ✓ Hoạt độngATMEGA169A-MU Tóm tắt
An 8-bit AVR microcontroller is a compact embedded-control platform that combines a RISC processor core, Flash program memory, data EEPROM, SRAM, timers, serial interfaces, and general-purpose I/O on one integrated circuit. The ATmega169A belongs to the ATmega family of 8-bit CMOS RISC microcontrollers, where the CPU executes instructions from embedded Flash while retaining data in SRAM and EEPROM. It is intended for compact control systems that require deterministic peripheral integration without a higher-cost processor or external memory.
Key device resources include 16 KB of ISP Flash, 512 bytes of EEPROM, 1 KB of SRAM, 54 or 69 general-purpose I/O lines depending on the device variant, and 32 general-purpose working registers. The ISP Flash supports in-system programming, and its read-while-write capability permits program-memory access during operation. The integrated memory and I/O resources make the microcontroller suitable for control, communications, sensing, and low-to-medium-rate data-processing tasks.
The ATmega169A uses the AVR architecture and is associated with the picoPower family identified by Microchip for the ATmega169PA. Its operating range of 2.5 V to 5 V accommodates both 3.3 V and 5 V equipment when the surrounding circuitry remains compatible with the selected operating voltage. The 16 MHz operating point provides useful processing headroom for event-driven control, while timer, serial, and parallel interfaces support common embedded-system functions.
Typical uses include industrial sensor controllers, building and automation equipment, compact motor-control subsystems, instrumentation, communication modules, and low-power embedded control boards. For designs requiring the exact ATmega169A feature set, the firmware should be validated for the selected voltage, clock configuration, peripheral set, and package footprint before production release.
PCB implementation must account for the 64-QFN exposed thermal pad, its required footprint geometry, and the manufacturer’s recommended land pattern. Decoupling should be placed directly beside the supply pins, programming and reset signals should remain accessible, and the exposed pad should be connected to the intended ground plane according to the manufacturer’s package recommendations.
This product record combines the exact manufacturer and distributor package, memory, clock, voltage, and ordering information with purchasing guidance, application context, and design-oriented engineering notes. It also distinguishes the exact ATMEGA169A-MU ordering code from similarly named package, reel, or related-device variants so engineers can verify footprint and firmware compatibility before substitution.
Bộ thay thế dễ dàng lắp đặt cho ATMEGA169A-MU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATMEGA169A-MU (cùng hình factor và footprint) — khác nhau ở Package, Supply Voltage Range, Flash Memory, Instructions, Program Memory Type.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếATMEGA169A-MU Tỷ lệ tối đa & tính chất điện
| Microcontroller Type | 8-bit AVR RISC CMOS microcontroller |
| Tần số xung maksimum | 16 MHz |
| Flash Memory Size | 16 KB |
| Flash Organization | 8K x 16 |
| Program Memory Type | ISP Flash with read-while-write capability |
| EEPROM Size | 512 bytes |
| SRAM Size | 1 KB |
| General-Purpose I/O Lines | 54/69 lines |
| General-Purpose Working Registers | 32 registers |
| Operating Voltage Range | 2.5 V to 5 V |
| Hộp | 64-QFN (9 mm x 9 mm) with exposed pad |
| Kiểu lắp đặt | Surface mount |
| Core Architecture | AVR 8-bit RISC |
| Programming Interface | In-system programming (ISP) |
| Process Technology | CMOS |
| Power Class | Low-power microcontroller |
| Trạng thái RoHS | Compliant |
| Manufacturer Product Family | ATmega 8-bit AVR microcontroller family |
| Ordering Code | ATMEGA169A-MU |
Hướng dẫn cấu hình chân ATMEGA169A-MU 64-qfn (9 mm x 9 mm) with exposed pad
Cấu hình chân cho ATMEGA169A-MU (64-qfn (9 mm x 9 mm) with exposed pad gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATMEGA169A-MU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATMEGA169A-MU phù hợp cho 6 Áp dụngs: Industrial Sensor Controller, Building Automation Module, Compact Motor-Control Subsystem, Instrumentation and Data Logger, Low-Power IoT Sensor Node, Communication Interface Module.
Industrial Sensor Controller
The ATMEGA169A-MU fits an industrial sensor controller that must combine local signal conditioning, digital filtering, and an industrial communication interface on one compact device. Its 16 MHz AVR core provides useful processing headroom for sensor sampling and protocol handling, while 16 KB of ISP Flash accommodates application firmware and 1 KB of SRAM supports bounded working buffers. The 512-byte EEPROM can retain calibration constants, configuration data, or production settings. In a controller implementation, the device can timestamp samples, apply limits and compensation, and transmit results through an appropriate serial interface. The 2.5 V to 5 V operating range supports common embedded rails, but the 64-QFN exposed-pad layout requires careful decoupling and thermal design on the PCB.
Được đề xuất
Building Automation Module
The ATMEGA169A-MU is appropriate for a building-automation module that consolidates environmental inputs, actuator control, and status reporting. Its 16 KB Flash stores a compact control application, 1 KB of SRAM supports runtime state, and the 54 or 69 general-purpose I/O lines provide flexible connections to digital sensors, relay drivers, and status indicators. The microcontroller can scan inputs on timer events, apply hysteresis and scheduling logic, and update a communications module. Its 2.5 V to 5 V range allows deployment in both 3.3 V and 5 V controller architectures. Engineering attention should center on exposed-pad grounding, supply decoupling near the device, and firmware defaults that place unused I/O into safe states during startup or communication loss.
Được đề xuất
Compact Motor-Control Subsystem
The ATMEGA169A-MU can serve as the supervisory controller in a compact motor or actuator subsystem where a dedicated high-performance motor-control processor would be unnecessary. The 16 MHz AVR core can execute position or speed-control logic, monitor limit switches, and coordinate current or direction commands, while its timer resources support deterministic edge and interval generation. With 16 KB of Flash, 1 KB of SRAM, and 512 bytes of EEPROM, the device provides adequate resources for compact supervisory logic, parameter storage, and diagnostics. The MCU should not drive high current directly; external power stages and protection are required. Its small 64-QFN footprint supports dense control assemblies, although the exposed pad and 9 mm by 9 mm body still require a carefully designed thermal path.
Được đề xuất
Instrumentation and Data Logger
The ATMEGA169A-MU is well suited to a compact instrumentation node that samples slow or moderate-rate signals, applies calibration, and stores configuration or event data. Its 16 MHz processing capability permits digital filtering and protocol assembly in an 8-bit architecture, while the 512-byte EEPROM is appropriate for calibration coefficients and serial numbers. The 1 KB of SRAM can support temporary measurement buffers, while 16 KB of ISP Flash provides room for the control and logging application. A typical design connects analog front-end circuitry to the MCU’s converters, stores processed samples in external nonvolatile memory when required, and reports data through a serial link. The 2.5 V to 5 V range supports low-voltage sensor systems as well as 5 V legacy instruments, provided the chosen clock and peripherals are valid at the operating voltage.
Được đề xuất
Low-Power IoT Sensor Node
The ATMEGA169A-MU can serve as the local processing element in a low-power IoT sensor node when the design values integration, deterministic control, and modest memory use over a high-performance application processor. The 16 KB ISP Flash holds a compact acquisition and communication task, 1 KB of SRAM supports transient sensor and network data, and 512 bytes of EEPROM preserves identifiers or calibration values. Timer-driven sampling can reduce unnecessary activity, while the serial peripheral can connect a radio module. Because the ATmega169A does not integrate wireless communications, the radio remains a separate component and its sleep current can dominate the node budget. Firmware should use the device’s low-power operating modes effectively, and the 64-QFN exposed pad should be tied to the recommended ground plane to preserve electrical and thermal performance.
Được đề xuất
Communication Interface Module
The ATMEGA169A-MU is suitable for a dedicated communication interface or protocol-conversion module when the design needs local framing, configuration, diagnostics, and status control. Its 16 MHz AVR core can handle protocol parsing and response generation, while 16 KB of Flash stores the protocol stack and 1 KB of SRAM supports packet assembly. General-purpose I/O lines can provide hardware flow control, configuration inputs, and fault indicators. The device can bridge a local serial interface to a network PHY or transceiver selected for the required physical layer. Because the MCU does not itself provide Ethernet or a complete modern network stack, the external interface must be matched to the protocol and bandwidth requirements. The compact QFN package helps minimize board area, but exposed-pad grounding and local bypass placement remain essential for reliable communication at short cable lengths and industrial edge rates.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATMEGA169A-MU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Bảo phân biệt quan trọng
- Exact 64-QFN tray ordering code (vsATMEGA169A-MUR)
- 16 MHz AVR processing rate with 16 KB ISP Flash (vsATMEGA165A-MUR)
- Single-part integration for compact control designs (vsATMEGA165A-MUR)
Ghi chú thiết kế
Use the exact 64-QFN land pattern and exposed-pad geometry from Microchip’s ATmega169A package drawing rather than a generic QFN footprint. The verified package description specifies a 64-QFN measuring 9 mm by 9 mm with an exposed pad. Confirm pad dimensions, solder-mask clearance, paste-aperture design, and courtyard rules from the manufacturer drawing. A footprint error can shift every lead and compromise solderability, particularly because the exposed pad materially influences both assembly and thermal performance.
Place the required bypass capacitors adjacent to the ATMEGA169A-MU supply and ground pins, following the placement and capacitance recommendations in the current manufacturer datasheet. Keep the high-frequency return path short and connect the exposed pad to the intended ground plane with the prescribed via pattern. Because this device supports 2.5 V to 5 V operation, verify that the selected regulator, clock source, peripherals, and external signal levels are valid at the actual supply voltage.
Preserve access to the reset and in-system programming signals while keeping sensitive timing and communication routes away from noisy switching nodes. Route clock and programming traces with short paths, maintain a continuous ground reference, and isolate analog or sensor inputs from relay drivers and other high-current switching paths. Although the ATMEGA169A-MU is an 8-bit MCU rather than a high-speed digital interface device, layout discipline remains important when timers, serial links, and external communications share a compact board.
Do not treat ATMEGA169A-MUR as an unrestricted substitute for ATMEGA169A-MU: the core device family is the same, but the packing suffix differs. Likewise, a shared 64-QFN package and similar memory capacity do not prove that ATMEGA165A-MUR or ATMEGA169PA has identical pin functions, peripheral mapping, interrupt behavior, or firmware support. For any substitution, compare the complete pin list, clock system, peripheral registers, boot and fuse behavior, voltage limits, and package drawings before updating the approved BOM.
Thông tin tuân thủ
The verified device listing identifies the ATMEGA169A-MU as RoHS compliant. No RoHS-independent REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals status was established for the exact ordering code.