ATSAMD21E16B-MF - 48MHz Cortex-M0+ MCU | Microchip Technology
MPN: ATSAMD21E16B-MF ✓ Hoạt độngATSAMD21E16B-MF Tóm tắt
A microcontroller is a programmable semiconductor that combines a CPU core, memory, and peripherals on one integrated circuit. The ATSAMD21E16 belongs to the SAM D21 family of general-purpose, low-power embedded processors. In the product hierarchy, it is an ARM Cortex-M0+ microcontroller, a 32-bit microcontroller, and an embedded-system controller commonly used for local sensing, communications, control, and human-interface functions.
The principal features of the ATSAMD21E16B-MF include its 48 MHz Cortex-M0+ core, 64 KB Flash program memory, and 8 KB SRAM. The 1.62 V to 3.6 V operating range supports low-voltage 3.3 V system designs while accommodating lower operating points for power-sensitive equipment. Its industrial temperature qualification covers -40°C to +125°C, and the 5 x 5 mm QFN-EP package supports compact PCB layouts.
The SAM D21 architecture is intended for low-cost, low-power embedded designs in which efficient event handling and integration of analog and digital functions are important. The Cortex-M0+ processor uses a 32-bit instruction set, while the device family combines serial communications, timers, and analog conversion resources in one package. The exposed pad provides a thermal and electrical connection to the PCB under the device.
Typical applications include industrial sensor controllers, compact data loggers, USB-connected peripherals, building-control nodes, and embedded instrument interfaces. The ATSAMD21E16B-MF is particularly suitable when local conversion, serial communications, and deterministic control are required without using a higher-cost Cortex-M3 or Cortex-M4 core. Its 48 MHz processing rate also provides useful headroom for protocol handling and moderate control-loop workloads.
PCB implementation should preserve the manufacturer's recommended decoupling and exposed-pad connection details. Place the input and output capacitors close to their associated power pins, connect the exposed pad to the ground plane, and confirm the pin assignment against the device data sheet before routing sensitive analog inputs. The wide temperature range makes the part suitable for industrial environments, but enclosure temperature, self-heating, and nearby heat sources must still be considered.
This product record combines the device architecture, package and environmental characteristics, verified manufacturer and distributor information, application guidance, and engineering-focused design considerations. It also provides a framework for comparing the ATSAMD21E16B-MF with related Microchip devices while keeping pin compatibility, memory requirements, package construction, and operating conditions as the principal selection criteria.
Bộ thay thế dễ dàng lắp đặt cho ATSAMD21E16B-MF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMD21E16B-MF (cùng hình factor và footprint) — khác nhau ở Package, RoHS Status.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếATSAMD21E16B-MF Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Tần số xung maksimum | 48 MHz |
| Core Architecture | ARM Cortex-M0+ |
| Processor Width | 32 bit |
| Flash Memory | 64 KB |
| SRAM | 8 KB |
| Operating Voltage Range | 1.62 V to 3.6 V |
| Nominal Supply Voltage | 3.3 V |
| ADC Resolution | 10 bit and 12 bit |
| GPIO Count | 26 |
| Khoảng nhiệt độ hoạt động | -40°C to +125°C |
| Hộp | 32-pin QFN-EP (5 x 5 mm) |
| Kiểu lắp đặt | Surface mount |
| Exposed Pad | Present |
| Packaging Form | Tray |
| Green / Environmental Status | Green |
| Trạng thái RoHS | RoHS compliant |
| Functional Safety | Functional Safety (FuSa) device |
| Program Memory Type | Embedded Flash |
Hướng dẫn cấu hình chân ATSAMD21E16B-MF 32-pin qfn-ep (5 x 5 mm)
Cấu hình chân cho ATSAMD21E16B-MF (32-pin qfn-ep (5 x 5 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATSAMD21E16B-MF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATSAMD21E16B-MF phù hợp cho 6 Áp dụngs: Industrial Sensor Controller, USB Connected Peripheral, Compact Data Logger, Building Control Node, Precision Instrument Interface, Embedded Communication Gateway.
Industrial Sensor Controller
The ATSAMD21E16B-MF fits industrial sensor nodes that combine analog measurement, digital conditioning, and local communications. Its 48 MHz Cortex-M0+ core provides processing headroom for filtering and protocol handling, while 64 KB Flash and 8 KB SRAM suit moderate firmware stacks. The 10-bit and 12-bit ADC resources support sensors requiring more than one conversion resolution, and 26 GPIO provide connections for inputs, outputs, status indicators, and alarms. Operating from 1.62 V to 3.6 V supports low-voltage sensor rails, while the -40°C to +125°C specification accommodates demanding industrial environments. The compact 5 x 5 mm QFN-EP package reduces board area, although designers should preserve the manufacturer's exposed-pad layout and verify sensor accuracy at the selected voltage and temperature.
Được đề xuất
USB Connected Peripheral
The ATSAMD21E16B-MF is suitable for compact USB-connected accessories requiring local control, configuration storage, and protocol handling. Its 48 MHz 32-bit Cortex-M0+ processor can support peripheral tasks and serial communication, while 64 KB Flash provides space for application firmware and 8 KB SRAM supports working buffers. Operating at a nominal 3.3 V simplifies integration with many USB transceiver and logic components. Designers should confirm the required USB controller, transceiver, connector, protection scheme, and bus-routing topology in the selected SAM D21 configuration. The 32-pin QFN-EP package supports dense layouts, but exposed-pad connection, local decoupling, and controlled impedance remain essential for reliable USB signal integrity.
Được đề xuất
Compact Data Logger
The ATSAMD21E16B-MF can serve as the control processor in a compact data logger that records sensor values, timestamps events, and transfers information through a serial interface. The 48 MHz Cortex-M0+ core handles scheduling and data formatting, while 64 KB Flash stores firmware and 8 KB SRAM accommodates buffers during acquisition and transmission. The 26 GPIO allows connection of sensors, storage-control signals, status LEDs, and user controls. A 3.3 V operating point supports common embedded peripherals, and the -40°C to +125°C specification covers broad industrial environments. Flash endurance, write-cycle requirements, brownout behavior, and backup strategy should be evaluated according to the logging duty cycle. Board layout should separate analog inputs from switching nodes and route exposed-pad current into the ground system effectively.
Được đề xuất
Building Control Node
The ATSAMD21E16B-MF is appropriate for low-cost building-control nodes that monitor inputs and control actuators through embedded serial interfaces. Its 48 MHz Cortex-M0+ performance supports event handling, protocol servicing, and supervisory logic, while 64 KB Flash and 8 KB SRAM provide adequate capacity for compact gateway software. The 26 GPIO can be assigned to digital sensors, alarm inputs, indicator outputs, and status controls. The device's 1.62 V to 3.6 V operating range allows low-power design choices, and its -40°C to +125°C specification supports equipment intended for industrial environments. Installation conditions can still create local temperature rises, so enclosure placement and thermal analysis remain important. Firmware should include communication retries, safe-state behavior, and recovery logic for disconnected or corrupted sensors.
Được đề xuất
Precision Instrument Interface
The ATSAMD21E16B-MF can control compact test and measurement instruments where local calibration, status reporting, and communication are needed. Its 48 MHz Cortex-M0+ core provides deterministic control for front-panel functions and data preparation, and its 64 KB Flash and 8 KB SRAM are suitable for moderate embedded applications. The 10-bit and 12-bit ADC resources can serve supervisory or auxiliary measurement channels where greater resolution is not required. The 5 x 5 mm QFN-EP package allows placement close to analog and interface circuitry, helping keep sensitive routes compact. Designers should use separate analog and digital grounding strategies, follow the package-specific exposed-pad guidance, and avoid routing high-current switching paths near precision inputs. Firmware must also distinguish measurement commands from configuration updates to maintain deterministic operation.
Được đề xuất
Embedded Communication Gateway
The ATSAMD21E16B-MF is suitable for small embedded gateways that translate between local serial interfaces and a host processor. Its 48 MHz Cortex-M0+ core can manage protocol conversion, buffer handling, and supervisory tasks, while 64 KB Flash and 8 KB SRAM accommodate compact networking and firmware layers. The 26 GPIO can support status LEDs, reset control, interface selection, and recoverable configuration lines. A 3.3 V operating point aligns with many communication components, although every attached device must be checked against the 1.62 V to 3.6 V MCU supply range. The 32-pin QFN-EP construction supports space-constrained boards, but power sequencing, ground return paths, and signal integrity must be designed around the manufacturer package recommendations. Firmware should include watchdog recovery and robust handling of partial or malformed serial messages.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMD21E16B-MF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Product Type | 32-bit ARM Cortex-M0+ microcontroller |
| Maximum Clock Frequency | 48 MHz |
| Flash Memory | 64 KB |
| SRAM | 8 KB |
| Operating Voltage Range | 1.62 V to 3.6 V |
| Operating Temperature Range | -40°C to +125°C |
| ADC Resolution | 10 bit and 12 bit |
| GPIO Count | 26 |
| Package | 32-pin QFN-EP (5 x 5 mm) |
| Brand | Microchip Technology |
Bảo phân biệt quan trọng
- Extended 125°C temperature configuration (vsATSAMD21E16B-MU)
- Compact exposed-pad package integration (vsATSAMD21E16B-AZVAO)
- Consistent low-voltage 3.3 V architecture (vsATSAMD21J17A-MF)
Ghi chú thiết kế
Follow the ATSAMD21E16B package drawing and pin-description table when creating the QFN-EP footprint. The ATSAMD21E16B-MF uses a 5 x 5 mm package with an exposed pad, so the pad must be connected according to the manufacturer land-pattern guidance. Place the required input, output, and bypass capacitors close to their power pins, minimize loop area, and provide uninterrupted ground-plane access beneath the exposed pad to support both electrical and thermal performance.
Design the supply rail for the full 1.62 V to 3.6 V device range and the selected peripheral loads. Check regulator headroom, startup behavior, and the MCU's current consumption under the intended clock, analog, and communication configuration. Place bulk capacitance near the power source and local ceramic decoupling at the package pins. Confirm brownout and power-reset behavior in the firmware design, especially where Flash writes or external interface state must survive an unexpected supply interruption.
Separate analog inputs, ADC references, and sensitive communication routes from switching or high-current paths. Use the manufacturer pin-multiplexing table before assigning multiplexing capabilities because alternate peripheral functions can constrain the usable 26 GPIO lines. Keep the debug and programming interface accessible after assembly, and check every external signal against the device's operating-voltage and absolute-maximum limits. The exact pin names are not enumerated here; use the package-specific data sheet table for final schematic and netlist work.
The exposed pad is an important thermal path, but its effectiveness depends on the PCB stack-up, copper area, and internal via arrangement. Provide a continuous ground reference beneath the device and thermal vias where recommended by Microchip's package guidance. Estimate worst-case junction temperature from ambient temperature, board thermal resistance, and total device dissipation. Actual operating temperature can exceed ambient because nearby regulators, power devices, and enclosed electronics also contribute heat.
Do not treat ATSAMD21E16B-MF, ATSAMD21E16B-MU, ATSAMD21E16B-MFT, and other ordering suffixes as automatically interchangeable. Package dimensions, temperature grade, tape-and-reel or tray format, and device suffix conventions can differ. Validate the exact ordering code, exposed-pad implementation, supported temperature range, and firmware assumptions. Reusing an existing PCB also requires confirmation that the alternate suffix has the same pin multiplexing, electrical limits, and startup behavior.
Thông tin tuân thủ
The product listing identifies the ATSAMD21E16B-MF as RoHS compliant and green. No manufacturer declarations establishing REACH, halogen-free, conflict-minerals, or AEC-Q100 status were returned. AEC-Q100 is marked not applicable because the identified ordering configuration is a general-purpose industrial-temperature MCU rather than an explicitly automotive-qualified variant.