ATSAMD21E17D-AU - 48MHz Cortex-M0+ MCU | Microchip
MPN: ATSAMD21E17D-AU ✓ Hoạt độngATSAMD21E17D-AU Tóm tắt
A microcontroller is a programmable system-on-chip that combines a processor core, nonvolatile program memory, volatile data memory, and peripherals on one integrated circuit. The ATSAMD21E17 belongs to the SAM D21 family, a hierarchy of ARM Cortex-M0+ microcontroller -> embedded microcontroller -> semiconductor. Its 32-bit processing architecture supports efficient control tasks while retaining a compact and low-power design suited to battery-powered and connected products.
Key device attributes include a 48 MHz Cortex-M0+ core, 128 KB of flash, and 16 KB of SRAM. The SAM D21 family also provides 4 KB of read-write-write memory, USB connectivity, and a Functional Safety-capable configuration within its device family. The industrial-temperature variant provides a sensible choice for equipment that must operate reliably across a wider environmental range than consumer-rated options.
The 128 KB flash partition gives embedded firmware room for application code, protocol stacks, and configuration data, while 16 KB of SRAM supports working state, buffers, and real-time control tasks. Operating the core at 48 MHz provides useful processing headroom without requiring a larger system. Peripheral integration also allows a compact design to connect sensors, communication equipment, and external nonvolatile memory without excessive discrete components.
Typical applications include connected home equipment, industrial sensing nodes, utility metering, consumer controls, USB-connected accessories, and compact embedded products. In each case, the microcontroller combines local control processing with USB connectivity and enough memory to organize firmware without relying on an external storage device. The 32-pin TQFP package is also convenient for prototypes and designs requiring a broad mix of general-purpose I/O.
PCB design should preserve clean supply routing and place decoupling capacitors close to the device power pins. USB signal routing requires controlled impedance, short traces, and a properly configured return path. Firmware development should use the pin-description table and memory map in the manufacturer datasheet, and production programming should follow the assigned programming interface and packing-code requirements.
This page organizes the ATSAMD21E17D-AU specifications, verified sourcing links, same-package alternatives, and practical selection guidance. It also highlights the differences between tray and tape-and-reel order codes so engineers can distinguish mechanical packaging from changes in electrical function.
Bộ thay thế dễ dàng lắp đặt cho ATSAMD21E17D-AU — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với ATSAMD21E17D-AU (cùng hình factor và footprint) — khác nhau ở Package, SRAM, Flash Memory, RoHS Status, ADC.
ATSAMD21E17A-AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD21E18A-AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD21J17A-AU
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →ATSAMD21E17D-AU Tỷ lệ tối đa & tính chất điện
| Product Type | 32-bit ARM Cortex-M0+ flash microcontroller |
| CPU Core | Arm Cortex-M0+ |
| Architecture | 32-bit RISC |
| Tần số xung maksimum | 48 MHz |
| Flash Memory | 128 KB |
| Flash Organization | 128K x 8 bits |
| SRAM | 16 KB |
| Read-Write-Write Memory | 4 KB |
| Điện áp cung cấp hoạt động | 1.6 V to 3.6 V |
| USB Interface | Yes |
| Functional Safety Support | Yes |
| Hộp | 32-pin TQFP, 7 x 7 mm |
| Terminal Count | 32 terminals |
| Lead Form | Gull wing |
| Temperature Grade | Industrial |
| Order Code Packing | Tray |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | Green |
Hướng dẫn cấu hình chân ATSAMD21E17D-AU 32-pin tqfp, 7 x 7 mm
Cấu hình chân cho ATSAMD21E17D-AU (32-pin tqfp, 7 x 7 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho ATSAMD21E17D-AU.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
ATSAMD21E17D-AU phù hợp cho 6 Áp dụngs: Industrial Sensor and Control Node, Smart Home and Automation Controller, Utility Metering and Data Logger, USB-Connected Consumer Accessory, Low-Power Connected Instrument, Embedded System Timing and Peripheral Hub.
Industrial Sensor and Control Node
The ATSAMD21E17D-AU fits compact industrial sensing nodes that combine local control, data processing, and USB connectivity. Its 48 MHz Arm Cortex-M0+ core provides timing margin for sensor sampling, filtering, and communication tasks, while 128 KB of flash accommodates application firmware, configuration data, and USB protocol code. The 16 KB SRAM supports packet buffers and working state without requiring an external memory device in many designs. The industrial temperature grade is relevant to equipment exposed to variable ambient conditions. Designers should verify the exact analog and digital peripheral assignments in the pin table, then isolate sensitive analog inputs and provide stable, locally decoupled supply rails.
Được đề xuất
Smart Home and Automation Controller
The ATSAMD21E17D-AU is suitable for smart-home controllers that coordinate inputs, local logic, user interfaces, and USB-connected accessories. Its 48 MHz Cortex-M0+ processor can service event handling and communication routines, while 128 KB of flash leaves room for a structured firmware image and 16 KB of SRAM handles short-lived control data. USB support is useful for configuration, diagnostics, or a local service connection. In a hub or room-controller implementation, keep USB routing away from sensitive sensor traces, validate device startup behavior across all power states, and use the manufacturer's pin muxing guidance when assigning switches, displays, or communications peripherals.
Được đề xuất
Utility Metering and Data Logger
The ATSAMD21E17D-AU supports metering equipment that must acquire measurements, retain operating parameters, and periodically exchange data. The 128 KB flash provides space for measurement routines, correction tables, event logs, and USB firmware, while the 16 KB SRAM can buffer samples during collection. A 48 MHz core leaves processing margin for timestamp handling and communication tasks, and the 1.6 V to 3.6 V range accommodates low-energy regulator choices. Production designs should include a nonvolatile mechanism for critical counters where appropriate, protect calibration data from unintended writes, and verify the operating-temperature limits and communication requirements against the meter's environmental specification.
Được đề xuất
USB-Connected Consumer Accessory
The ATSAMD21E17D-AU is a practical controller for compact USB accessories that combine local logic with a host interface. Its USB capability can support configuration, data transfer, or peripheral service functions, while the Cortex-M0+ core handles protocol handling and application tasks. The 128 KB flash and 16 KB SRAM are sufficient for many control-centric accessories without external storage. USB layout requires particular care because connector, protection components, series resistors, and routing influence signal integrity. Follow the controller's USB guidance for impedance, branch placement, grounding, and test-point access, and use the 32-pin TQFP footprint with adequate copper and assembly clearances around fine-pitch leads.
Được đề xuất
Low-Power Connected Instrument
The ATSAMD21E17D-AU suits low-power connected instruments where local acquisition, control, and a host data path must coexist in a small footprint. The low-power ARM Cortex-M0+ architecture can remain efficient during routine control, while the 48 MHz operating point provides capacity for active filtering and protocol handling. With 128 KB flash and 16 KB SRAM, moderate instrument firmware can operate internally, including USB command handling. Low-power design still depends on the application firmware, clock strategy, analog front end, and regulator behavior rather than MCU frequency alone. Validate sleep currents, wake sources, USB enumeration behavior, and brownout recovery across the full supply range before finalizing the power architecture.
Được đề xuất
Embedded System Timing and Peripheral Hub
The ATSAMD21E17D-AU can act as the central controller in a compact embedded peripheral hub that aggregates digital I/O, communication links, and local automation logic. Its 48 MHz processor supports responsive state-machine control, while 128 KB of flash can hold application code and 16 KB of SRAM can buffer protocol transactions. The industrial temperature grade is useful for equipment beyond consumer environments, provided the complete assembly meets its own environmental targets. Pin multiplexing should be planned before PCB routing because general-purpose I/O, USB, debug, and communications functions may share package positions. Preserve debug access, define reset behavior for attached peripherals, and test power sequencing when external devices require controlled rail ordering.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho ATSAMD21E17D-AU — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | ATSAMD21E17A-AU | ATSAMD21E18A-AU | ATSAMD21J17A-AU |
|---|---|---|---|---|
| Brand | Microchip Technology | Microchip Technology | Microchip Technology | Microchip Technology |
| Package | 32-TQFP (7 x 7 mm) | 32-TQFP (7 x 7 mm) | 32-TQFP (7 x 7 mm) | 32-TQFP (7 x 7 mm) |
| CPU Core | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ | Arm Cortex-M0+ |
| Maximum Frequency | 48 MHz | 48 MHz | 48 MHz | 48 MHz |
| Flash Memory | 128 KB | 128 KB | 128 KB | 128 KB |
| SRAM | 16 KB | 16 KB | 16 KB | 16 KB |
| Order Code Packing | Tray | Tray | Tray | Tray |
Bảo phân biệt quan trọng
- Uses the 32-pin E-series TQFP footprint (vsATSAMD21G17D-AU)
- Direct ordering match for tray-based manufacturing (vsATSAMD21E17D-AUT)
- Combines 128 KB flash, 16 KB SRAM, and USB (vsATSAMD21J17A-AU)
Ghi chú thiết kế
Route the ATSAMD21E17D-AU supply pins directly to a continuous ground reference and place the required bypass capacitors close to their respective pins. Keep the USB differential pair short, symmetric, and over an uninterrupted reference plane. Use the manufacturer's pin and layout guidance for debug access, programming connections, and exposed package requirements. Fine-pitch TQFP assembly also benefits from clearances that accommodate component placement tolerances and soldering inspection requirements.
Design the 1.6 V to 3.6 V rail so it remains within tolerance during startup, USB attachment, load transitions, and brownout recovery. Verify the regulator's startup behavior against any external loads that can back-feed the MCU. Use a dedicated USB path where required, and place protection components near the connector. Before production, measure the rail at the MCU pins under worst-case processing, USB activity, and temperature conditions rather than relying only on the supply output.
Do not substitute the ATSAMD21G17D-AU for this device on a 32-pin board: the G-series option is associated with a 48-pin TQFP package. Likewise, do not treat the AU and AUT suffixes as interchangeable without accounting for tray versus tape-and-reel handling. For any A-series replacement, compare the pin-description table, peripheral set, device identification, and firmware support. Shared flash and SRAM capacities do not establish complete pin-to-pin compatibility.
Keep sensitive analog inputs away from USB, clock, and switching-node routes, and provide a quiet ground path for referenced measurements. Where the MCU must drive external signals through connectors, use series damping where appropriate and account for lead inductance in the 32-pin TQFP layout. Preserve access to programming and debug test points so production programming, boundary scan, and failure analysis remain practical after assembly.
Thông tin tuân thủ
The component listing identifies the device as green, but no explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was found for the exact order code.