BCM5241A1KMLG - 10/100 Ethernet PHY | Broadcom Limited
MPN: BCM5241A1KMLG ✓ Hoạt độngBCM5241A1KMLG Tóm tắt
An Ethernet PHY is the physical-layer component in an Ethernet communications system. It converts digital data from a MAC or network processor into signals suitable for a twisted-pair cable and reconstructs incoming signals for the digital controller. In the network hierarchy, a PHY is a network interface IC and a semiconductor device within the broader category of Ethernet interface integrated circuits. The BCM5241 supports both 10 Mb/s and 100 Mb/s copper links for legacy Fast Ethernet equipment.
The BCM5241A1KMLG provides one transmit driver and one receive channel for a single-port design. Its identified 2.5 V and 3.3 V operating options allow implementation with either a 2.5 V core-side supply or a 3.3 V interface-side supply where the surrounding circuitry permits it. Its listed 170 mW power figure is relevant to compact embedded systems, although the actual board-level consumption depends on operating mode, network activity, supply voltage, and the external circuit configuration.
Broadcom identifies BCM5241A1KMLG as an active MII PHY transceiver. MII, or Media Independent Interface, separates the PHY from the digital MAC through standardized control, data, and status signals. This division of responsibility allows the same physical-layer circuit to support multiple Ethernet MAC implementations. The device also supports 100BASE-EFX, extending its application scope beyond the conventional 10BASE-T and 100BASE-TX copper modes listed for the part.
Typical uses include industrial Ethernet controllers, embedded routers, print servers, set-top equipment, network interface adapters, and other equipment requiring a single copper Ethernet port. The part is particularly relevant where a 10/100 Mb/s connection is sufficient and board area, component count, and interface simplicity matter more than support for gigabit data rates.
PCB design should preserve the separation between digital circuitry, analog PHY signals, and the Ethernet transformer network. Keep the PHY supply bypass capacitors close to their power pins, route high-speed differential and analog signals over continuous ground planes, and follow the manufacturer pin-description table and recommended application layout when assigning tracks and test points.
This page organizes the Broadcom BCM5241 product information, verified distributor records, lifecycle status, interface characteristics, application guidance, and same-family replacement information into an engineering-focused reference for evaluating the BCM5241A1KMLG in a new Ethernet design.
Bộ thay thế dễ dàng lắp đặt cho BCM5241A1KMLG — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với BCM5241A1KMLG (cùng hình factor và footprint) — khác nhau ở Product Type.
BCM5241A1IMLG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BCM5241A1KML
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM5241A1KMLG-K
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BCM5241A1KMLG Tỷ lệ tối đa & tính chất điện
| Product Type | Ethernet physical-layer transceiver |
| Ethernet Support | 10BASE-T, 100BASE-TX, and 100BASE-EFX |
| Tốc độ dữ liệu | 10 Mb/s and 100 Mb/s |
| Port Count | 1 port |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Host Interface | MII |
| Điện áp cung cấp hoạt động | 2.5 V and 3.3 V |
| Typical Power | 170 mW |
| Product Status | Active |
| Introduction Date | April 29, 2001 |
| Manufacturer | Broadcom Limited |
| Trạng thái RoHS | Compliant |
| Maximum Data Rate | 100 Mb/s |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân BCM5241A1KMLG standard
Cấu hình chân cho BCM5241A1KMLG (standard gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho BCM5241A1KMLG.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BCM5241A1KMLG phù hợp cho 6 Áp dụngs: Industrial Ethernet Controller, Embedded Router, Print Server, Set-Top Box, Network Interface Adapter, Industrial Sensor Gateway.
Industrial Ethernet Controller
The BCM5241A1KMLG fits an industrial controller that needs a single 10/100 Mb/s copper Ethernet port and communicates with a network processor through MII. Its 10BASE-T, 100BASE-TX, and 100BASE-EFX support gives the design access to several Fast Ethernet modes, while the listed 170 mW operating power is appropriate for a compact embedded platform. The controller must provide a compatible MII timing and signal interface, and the analog network section must follow the manufacturer’s recommended transformer and filtering layout.
Được đề xuất
Embedded Router
An embedded router can use the BCM5241A1KMLG as the physical layer for one 10/100 Mb/s WAN or LAN copper connection. The single-driver, single-receiver arrangement limits the device to one port, which is appropriate for a small access point, gateway, or basic routing module where one Fast Ethernet uplink is sufficient. Its 2.5 V and 3.3 V operating options should be matched to the router’s power architecture, and controlled-impedance MII routing is necessary to preserve signal integrity between the processor and PHY.
Được đề xuất
Print Server
The BCM5241A1KMLG is suitable for a print-server main board that connects an embedded controller to 10/100 Mb/s Ethernet infrastructure. The supported 10BASE-T and 100BASE-TX modes allow the server to operate on both legacy 10 Mb/s and Fast Ethernet networks. Its single-port structure reduces the analog-channel count, while 2.5 V and 3.3 V supply operation provides flexibility in legacy industrial print equipment. Ethernet magnetics, isolation, surge protection, and the connector implementation still require system-level validation.
Được đề xuất
Set-Top Box
A set-top box can use the BCM5241A1KMLG to add a Fast Ethernet service connection without implementing a full multi-port switching fabric. Support for 10BASE-T, 100BASE-TX, and 100BASE-EFX makes the PHY applicable to common access networks and service equipment, while the listed 170 mW power is relevant to consumer-electronics thermal budgets. The digital controller must support an MII interface, and the PCB should isolate PHY clock and data routing from noisy power and video circuitry.
Được đề xuất
Network Interface Adapter
The BCM5241A1KMLG can provide the physical layer for a dedicated single-port network interface adapter connected to a host controller. Because the PHY supports both 10 Mb/s and 100 Mb/s operation, it is useful for adapters intended to connect older host systems to modern Fast Ethernet networks. Designers should verify MII clocking, signal termination, and supply sequencing because host-interface compatibility extends beyond simply matching the 10/100 Mb/s data rate.
Được đề xuất
Industrial Sensor Gateway
The BCM5241A1KMLG can add a wired Ethernet uplink to an industrial sensor gateway that already has a controller capable of operating the MII interface. A 100 Mb/s link allows collected process or environmental data to be aggregated without requiring gigabit PHY complexity, and the 170 mW listed operating power is useful in a compact DIN-mounted or embedded gateway. Field deployments must confirm temperature qualification, Ethernet isolation, surge withstand, and grounding practices.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BCM5241A1KMLG — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BCM5241A1IMLG | BCM5241A1KML | BCM5241A1KMLG-K |
|---|---|---|---|---|
| Brand | Broadcom Limited | Broadcom Limited | Broadcom Limited | Broadcom Limited |
| Package | BCM5241 manufacturer package | BCM5241 manufacturer package | BCM5241 manufacturer package | BCM5241 manufacturer package |
| Product Type | Ethernet transceiver | Ethernet PHY | Ethernet PHY | Ethernet PHY |
| Ethernet Data Rate | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
Bảo phân biệt quan trọng
- Single-port integration reduces the external PHY channel count (vsBCM5241A1IMLG)
- Supports three identified copper operating modes (vsBCM5241A1KML)
- Supports both 2.5 V and 3.3 V operating rails (vsBCM5241A1KMLG-K)
Ghi chú thiết kế
Separate the MII digital interface from the analog copper-network section and place the PHY close to the Ethernet transformer or connector. Use a continuous ground plane, avoid routing MII clock and data beneath switching supplies, and match trace geometry to the host controller’s MII requirements. The manufacturer’s BCM5241 Product Brief should govern the final pin assignment and reference layout because an incorrectly assigned or omitted pin can prevent link establishment.
Design the 2.5 V and 3.3 V supply paths so that the BCM5241 receives the voltage required by its selected operating mode without excessive ripple. Place the manufacturer-recommended bypass capacitors at the relevant power pins with short ground returns. Estimated: if the listed 170 mW typical operating power applies to the selected mode, approximately 68 mA corresponds to 2.5 V or 52 mA corresponds to 3.3 V; actual regulator capacity should include startup margin and other board loads.
Treat the MII interface as a synchronous digital interface and review clock source, timing margins, impedance, and trace length against the Broadcom product requirements. Provide a low-inductance ground reference, avoid stubs, and keep clock routing away from the analog PHY and Ethernet magnetics. When substituting a BCM5241 family candidate, repeat this review because ordering suffixes can correspond to differences in temperature grade or qualification even when the basic 10/100 Mb/s ratings remain the same.
Do not treat a 10/100 Mb/s PHY as a gigabit Ethernet device or assume that a similar Broadcom suffix guarantees production interchangeability. Confirm the exact package drawing, pin names, operating-temperature grade, supply sequencing, and approved status in the manufacturer product brief. For a second-source decision, compare the analog network and MII interfaces rather than relying only on the Ethernet speed and nominal operating voltage.
Thông tin tuân thủ
RoHS compliance is identified in the product listing. Automotive qualification, REACH status, lead-free construction, halogen-free status, and conflict-minerals reporting are not stated.