BCM5241A1KMLG - 10/100 Ethernet PHY | Broadcom Limited
MPN: BCM5241A1KMLG ✓ AktifBCM5241A1KMLG Ringkasan
An Ethernet PHY is the physical-layer component in an Ethernet communications system. It converts digital data from a MAC or network processor into signals suitable for a twisted-pair cable and reconstructs incoming signals for the digital controller. In the network hierarchy, a PHY is a network interface IC and a semiconductor device within the broader category of Ethernet interface integrated circuits. The BCM5241 supports both 10 Mb/s and 100 Mb/s copper links for legacy Fast Ethernet equipment.
The BCM5241A1KMLG provides one transmit driver and one receive channel for a single-port design. Its identified 2.5 V and 3.3 V operating options allow implementation with either a 2.5 V core-side supply or a 3.3 V interface-side supply where the surrounding circuitry permits it. Its listed 170 mW power figure is relevant to compact embedded systems, although the actual board-level consumption depends on operating mode, network activity, supply voltage, and the external circuit configuration.
Broadcom identifies BCM5241A1KMLG as an active MII PHY transceiver. MII, or Media Independent Interface, separates the PHY from the digital MAC through standardized control, data, and status signals. This division of responsibility allows the same physical-layer circuit to support multiple Ethernet MAC implementations. The device also supports 100BASE-EFX, extending its application scope beyond the conventional 10BASE-T and 100BASE-TX copper modes listed for the part.
Typical uses include industrial Ethernet controllers, embedded routers, print servers, set-top equipment, network interface adapters, and other equipment requiring a single copper Ethernet port. The part is particularly relevant where a 10/100 Mb/s connection is sufficient and board area, component count, and interface simplicity matter more than support for gigabit data rates.
PCB design should preserve the separation between digital circuitry, analog PHY signals, and the Ethernet transformer network. Keep the PHY supply bypass capacitors close to their power pins, route high-speed differential and analog signals over continuous ground planes, and follow the manufacturer pin-description table and recommended application layout when assigning tracks and test points.
This page organizes the Broadcom BCM5241 product information, verified distributor records, lifecycle status, interface characteristics, application guidance, and same-family replacement information into an engineering-focused reference for evaluating the BCM5241A1KMLG in a new Ethernet design.
Pilihan pengganti yang segera untuk BCM5241A1KMLG — sama paket, pin-pin kompatibel. Bahagian paket yang berbeza memerlukan kerja ulang PCB diasingkan.
Varietas dalam siri ini
Model serupa yang kompatibel dengan pengganti yang segera BCM5241A1KMLG (sama faktor bentuk dan kaki) — berbeza dalam Product Type.
BCM5241A1IMLG
✅ Masuk Drop-InHubungi untuk harga
Lihat Datasheet →BCM5241A1KML
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
BCM5241A1KMLG-K
✅ Masuk Drop-In📋 Alternatif rujukan (tidak dalam katalog)
BCM5241A1KMLG Penilaian maksimum & Ciri-ciri Elektrik
| Product Type | Ethernet physical-layer transceiver |
| Ethernet Support | 10BASE-T, 100BASE-TX, and 100BASE-EFX |
| Kadar Data | 10 Mb/s and 100 Mb/s |
| Port Count | 1 port |
| Number of Drivers | 1 driver |
| Number of Receivers | 1 receiver |
| Host Interface | MII |
| Tegangan Pemberi Arus Operasi | 2.5 V and 3.3 V |
| Typical Power | 170 mW |
| Product Status | Active |
| Introduction Date | April 29, 2001 |
| Manufacturer | Broadcom Limited |
| Status RoHS | Compliant |
| Maximum Data Rate | 100 Mb/s |
| Jenis Pemasangan | Surface mount |
Panduan Konfigurasi Pin BCM5241A1KMLG standard
Konfigurasi pin untuk BCM5241A1KMLG (standard pakai). Komponen analog ini mempunyai pin masukan, keluaran, dan kuasa. Rujuk dokumen pengeluar untuk konfigurasi pengecualian, pemulihan, dan pin aktifkan. Ideal untuk pengawasan isyarat dan litar pengukur.
Tiada data garisan pin yang diperoleh untuk BCM5241A1KMLG.
Rujuk kepada lembaran data untuk konfigurasi pin penuh.
Aplikasi Biasa
BCM5241A1KMLG patut untuk 6 aplikasis: Industrial Ethernet Controller, Embedded Router, Print Server, Set-Top Box, Network Interface Adapter, Industrial Sensor Gateway.
Industrial Ethernet Controller
The BCM5241A1KMLG fits an industrial controller that needs a single 10/100 Mb/s copper Ethernet port and communicates with a network processor through MII. Its 10BASE-T, 100BASE-TX, and 100BASE-EFX support gives the design access to several Fast Ethernet modes, while the listed 170 mW operating power is appropriate for a compact embedded platform. The controller must provide a compatible MII timing and signal interface, and the analog network section must follow the manufacturer’s recommended transformer and filtering layout.
Disebarkan
Embedded Router
An embedded router can use the BCM5241A1KMLG as the physical layer for one 10/100 Mb/s WAN or LAN copper connection. The single-driver, single-receiver arrangement limits the device to one port, which is appropriate for a small access point, gateway, or basic routing module where one Fast Ethernet uplink is sufficient. Its 2.5 V and 3.3 V operating options should be matched to the router’s power architecture, and controlled-impedance MII routing is necessary to preserve signal integrity between the processor and PHY.
Disebarkan
Print Server
The BCM5241A1KMLG is suitable for a print-server main board that connects an embedded controller to 10/100 Mb/s Ethernet infrastructure. The supported 10BASE-T and 100BASE-TX modes allow the server to operate on both legacy 10 Mb/s and Fast Ethernet networks. Its single-port structure reduces the analog-channel count, while 2.5 V and 3.3 V supply operation provides flexibility in legacy industrial print equipment. Ethernet magnetics, isolation, surge protection, and the connector implementation still require system-level validation.
Disebarkan
Set-Top Box
A set-top box can use the BCM5241A1KMLG to add a Fast Ethernet service connection without implementing a full multi-port switching fabric. Support for 10BASE-T, 100BASE-TX, and 100BASE-EFX makes the PHY applicable to common access networks and service equipment, while the listed 170 mW power is relevant to consumer-electronics thermal budgets. The digital controller must support an MII interface, and the PCB should isolate PHY clock and data routing from noisy power and video circuitry.
Disebarkan
Network Interface Adapter
The BCM5241A1KMLG can provide the physical layer for a dedicated single-port network interface adapter connected to a host controller. Because the PHY supports both 10 Mb/s and 100 Mb/s operation, it is useful for adapters intended to connect older host systems to modern Fast Ethernet networks. Designers should verify MII clocking, signal termination, and supply sequencing because host-interface compatibility extends beyond simply matching the 10/100 Mb/s data rate.
Disebarkan
Industrial Sensor Gateway
The BCM5241A1KMLG can add a wired Ethernet uplink to an industrial sensor gateway that already has a controller capable of operating the MII interface. A 100 Mb/s link allows collected process or environmental data to be aggregated without requiring gigabit PHY complexity, and the 170 mW listed operating power is useful in a compact DIN-mounted or embedded gateway. Field deployments must confirm temperature qualification, Ethernet isolation, surge withstand, and grounding practices.
Disebarkan
Ringkasan Produk Disebarkan
Data referensi kejuruteraan untuk BCM5241A1KMLG — perbandingan, panduan rancangan, dan maklumat kesediaan
Panduan Pilihan
Perbandingan dengan Gantian
| Parametr | Produk Ini | BCM5241A1IMLG | BCM5241A1KML | BCM5241A1KMLG-K |
|---|---|---|---|---|
| Brand | Broadcom Limited | Broadcom Limited | Broadcom Limited | Broadcom Limited |
| Package | BCM5241 manufacturer package | BCM5241 manufacturer package | BCM5241 manufacturer package | BCM5241 manufacturer package |
| Product Type | Ethernet transceiver | Ethernet PHY | Ethernet PHY | Ethernet PHY |
| Ethernet Data Rate | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s | 10 Mb/s and 100 Mb/s |
Penyeberangsung Jelas
- Single-port integration reduces the external PHY channel count (vsBCM5241A1IMLG)
- Supports three identified copper operating modes (vsBCM5241A1KML)
- Supports both 2.5 V and 3.3 V operating rails (vsBCM5241A1KMLG-K)
Catatan Desain
Separate the MII digital interface from the analog copper-network section and place the PHY close to the Ethernet transformer or connector. Use a continuous ground plane, avoid routing MII clock and data beneath switching supplies, and match trace geometry to the host controller’s MII requirements. The manufacturer’s BCM5241 Product Brief should govern the final pin assignment and reference layout because an incorrectly assigned or omitted pin can prevent link establishment.
Design the 2.5 V and 3.3 V supply paths so that the BCM5241 receives the voltage required by its selected operating mode without excessive ripple. Place the manufacturer-recommended bypass capacitors at the relevant power pins with short ground returns. Estimated: if the listed 170 mW typical operating power applies to the selected mode, approximately 68 mA corresponds to 2.5 V or 52 mA corresponds to 3.3 V; actual regulator capacity should include startup margin and other board loads.
Treat the MII interface as a synchronous digital interface and review clock source, timing margins, impedance, and trace length against the Broadcom product requirements. Provide a low-inductance ground reference, avoid stubs, and keep clock routing away from the analog PHY and Ethernet magnetics. When substituting a BCM5241 family candidate, repeat this review because ordering suffixes can correspond to differences in temperature grade or qualification even when the basic 10/100 Mb/s ratings remain the same.
Do not treat a 10/100 Mb/s PHY as a gigabit Ethernet device or assume that a similar Broadcom suffix guarantees production interchangeability. Confirm the exact package drawing, pin names, operating-temperature grade, supply sequencing, and approved status in the manufacturer product brief. For a second-source decision, compare the analog network and MII interfaces rather than relying only on the Ethernet speed and nominal operating voltage.
Maklumat Kesediaan
RoHS compliance is identified in the product listing. Automotive qualification, REACH status, lead-free construction, halogen-free status, and conflict-minerals reporting are not stated.