BQ4845YP-A4E3 - 5V Parallel RTC with Supervisor | Texas Instruments
MPN: BQ4845YP-A4E3 ✓ Hoạt độngBQ4845YP-A4E3 Tóm tắt
A real-time clock is a dedicated timekeeping and calendar integrated circuit that maintains date, day-of-week, hour, minute, and second information even when the main system supply is unavailable. The BQ4845 belongs to the RTC and clock-and-calendar IC category, within clock and timing integrated circuits and broader semiconductor timing-control devices. The BQ4845YP-A4E3 is intended for systems that retain external nonvolatile SRAM while the backup battery supplies the RTC and monitoring circuitry.
Key features include parallel BCD clock and calendar formatting, a 32.768 kHz crystal interface, backup-battery operation, an independent programmable watchdog timer, a power-fail interrupt warning, and a conditional chip-enable output. The commercial-grade device is supplied in a 28-DIP package measuring 0.600 inches, or 15.24 mm, across the row spacing. Its through-hole format is useful for industrial controllers, embedded systems, test equipment, and legacy-style equipment requiring a socketed or leaded real-time clock.
The BQ4845 architecture separates timekeeping from the host processor. The host reads and writes the parallel RTC registers, while the crystal oscillator maintains the timebase. The backup-cell path allows the clock and external SRAM write-control functions to continue during main-power loss, helping preserve system state. A programmable watchdog can reset the processor if software stops servicing the watchdog, and the power-fail warning provides an early indication that the system should enter a controlled shutdown sequence.
Typical applications include industrial data-acquisition systems, embedded controllers, telecommunications equipment, test-and-measurement instruments, and battery-backed embedded products. In a data-acquisition platform, the BQ4845YP-A4E3 can preserve event timestamps and protect external SRAM during unexpected supply interruption. In a controller, the watchdog and reset outputs improve recovery from firmware stalls or processor lockups.
Designers should verify the crystal load capacitance, oscillator layout, battery-backup implementation, and reset timing against the manufacturer datasheet. The 28-DIP footprint is not interchangeable with the surface-mount BQ4845S-A4NTR variant without PCB changes. This page combines verified manufacturer and distributor information with practical selection guidance and drop-in replacement analysis.
Bộ thay thế dễ dàng lắp đặt cho BQ4845YP-A4E3 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với BQ4845YP-A4E3 (cùng hình factor và footprint) — khác nhau ở Package, Product Type, Battery Voltage Output, Conditional Chip Enable Output, External SRAM Support.
BQ4845YP-A4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BQ4845YP-A4E3
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →BQ4845YP-A4
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →BQ4845YP-A4
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →BQ4845YP-A4E
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
BQ4845YP-A4E3 Thông số kỹ thuật
| Product Type | Real-time clock and calendar IC with CPU supervisor |
| Supply Voltage Range | 4.5 V to 5.5 V |
| Clock Crystal Frequency | 32.768 kHz |
| Clock Format | BCD |
| Date Format | BCD |
| Loại giao diện | Parallel |
| Hộp | 28-DIP (0.600 in, 15.24 mm) |
| Kiểu lắp đặt | Through-hole |
| Số lượng chân | 28 pins |
| Khoảng nhiệt độ hoạt động | 0 °C to 70 °C |
| Temperature Grade | Commercial |
| Backup Battery Support | 3 V backup battery connection |
| Backup Mode Clock Current | Less than 500 nA |
| Watchdog Timer | Yes, programmable timeout |
| Power-Fail Warning | Yes |
| Leap-Year Feature | Yes |
| Daylight Savings Feature | Yes |
| Alarm Feature | Yes |
| Conditional Chip Enable Output | CEOUT for external SRAM write protection |
| Backup Voltage Output | VOUT for battery-voltage monitoring |
| Trạng thái RoHS | RoHS compliant |
Hướng dẫn cấu hình chân BQ4845YP-A4E3 28-dip (0.600 in, 15.24 mm)
Cấu hình chân cho BQ4845YP-A4E3 (28-dip (0.600 in, 15.24 mm) gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho BQ4845YP-A4E3.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BQ4845YP-A4E3 phù hợp cho 6 Áp dụngs: Industrial Data-Acquisition Systems, Embedded Control Systems, Telecommunications Equipment, Test and Measurement Instruments, Battery-Backed Embedded Products, Servers and Network Equipment.
Industrial Data-Acquisition Systems
The BQ4845YP-A4E3 fits industrial data-acquisition systems that must preserve timestamps during a mains interruption or control-system reset. Its 32.768 kHz crystal timebase maintains BCD clock and calendar information, while the 3 V backup-battery path supports RTC operation when the main 4.5 V to 5.5 V supply collapses. The CE output can hold external SRAM write lines in an inactive state during backup, reducing the chance of corrupting acquisition state. The watchdog timer and power-fail warning also give a host controller time to record a shutdown event and reduce the risk of an uncontrolled restart.
Được đề xuất
Embedded Control Systems
The BQ4845YP-A4E3 is appropriate for legacy embedded controllers requiring a parallel real-time clock, calendar, and processor supervision in one device. The parallel interface avoids a serial bus and can connect directly to a processor's address and data lines. Its independent watchdog timer provides a recovery path when firmware stops servicing the system, while the CPU reset function is specified to remain valid as the supply approaches the lower operating limit. Backup operation preserves time and can protect external SRAM during temporary primary-power loss.
Được đề xuất
Telecommunications Equipment
The BQ4845YP-A4E3 supports telecommunications equipment that must retain event chronology and supervise a 5 V processor rail. Its real-time clock provides BCD seconds, minutes, hours, date, and calendar information from a 32.768 kHz crystal, enabling repeatable logs and scheduled maintenance records. The power-fail warning can notify firmware before the main supply falls below its operating range, and the backup cell can maintain the RTC and SRAM write protection during the transition. The 28-DIP package is also appropriate for equipment platforms that retain through-hole memory and logic boards.
Được đề xuất
Test and Measurement Instruments
The BQ4845YP-A4E3 is useful in test-and-measurement instruments where event logs, calibration schedules, and operator actions must remain time-aligned across a power interruption. A 32.768 kHz crystal provides the RTC timebase, while the backup-battery path keeps the clock operating with less than 500 nA clock current in backup mode. The watchdog and power-fail functions give the instrument's controller a controlled recovery mechanism rather than relying on an external operator reset. The through-hole 28-DIP format also supports repair and obsolescence-management strategies for established platforms.
Được đề xuất
Battery-Backed Embedded Products
The BQ4845YP-A4E3 suits embedded products that use a 3 V backup cell to preserve volatile system context during main-power loss. The RTC continues counting time, the VOUT path allows the backup voltage to be monitored, and CE can prevent writes to external SRAM while primary power is unavailable. This combination supports reliable cold-start or recovery logic in controllers, instrument pods, and legacy industrial products. The principal design requirement is to follow the manufacturer battery-switchover and oscillator-layout guidance exactly.
Được đề xuất
Servers and Network Equipment
The BQ4845YP-A4E3 can support legacy servers and network-control equipment built around 5 V logic and parallel processors. It provides a persistent calendar and clock without relying on the host operating system, plus watchdog and reset supervision for unattended operation. During power loss, the backup cell maintains the RTC and can inhibit external SRAM writes through the conditional chip-enable output. This makes the device useful for equipment that records fault sequences or uses battery-backed configuration memory. Its 28-DIP footprint is appropriate for established boards rather than new space-constrained server designs.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BQ4845YP-A4E3 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BQ4845YP-A4 | BQ4845YP-A4E3 | BQ4845YP | BQ4845YP-A | BQ4845YP-A4E |
|---|---|---|---|---|---|---|
| Package | 28-DIP (0.600 in, 15.24 mm) | 28-DIP (0.600 in, 15.24 mm) | 28-DIP (0.600 in, 15.24 mm) | 28-DIP | 28-DIP | 28-DIP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Product Type | Parallel RTC and calendar with CPU supervisor | Parallel RTC and calendar | Parallel RTC and calendar | Parallel RTC and calendar | Parallel RTC and calendar | Parallel RTC and calendar |
| Operating Supply Voltage | 4.5 V to 5.5 V | 5 V | 4.5 V to 5.5 V | 5 V | 5 V | 5 V |
| Timebase Frequency | 32.768 kHz | 32.768 kHz | 32.768 kHz | 32.768 kHz | 32.768 kHz | 32.768 kHz |
| Clock and Date Format | BCD | BCD | BCD | BCD | BCD | BCD |
| Host Interface | Parallel | Parallel | Parallel | Parallel | Parallel | Parallel |
| Backup Battery Voltage | 3 V | 3 V | 3 V | 3 V | 3 V | 3 V |
| Special Features | Watchdog, alarm, power-fail warning, CE output, leap year, daylight savings | Watchdog, power-fail warning, SRAM backup control | Watchdog, alarm, power-fail warning, CE output, leap year, daylight savings | BQ4845 family feature set | BQ4845 family feature set | BQ4845 family feature set |
Bảo phân biệt quan trọng
- Combines RTC and system supervision in one device (vsBQ4802YPWR)
- Supports external SRAM write protection during backup operation (vsBQ4845S-A4NTR)
- Maintains the legacy 28-DIP footprint (vsBQ4845S-A4NTR)
Ghi chú thiết kế
Route the 32.768 kHz crystal and its load components close to the oscillator pins, keep the loop compact, and maintain a quiet ground return. Follow the Texas Instruments BQ4845 datasheet layout guidance and keep switching-node copper and high-current paths away from the oscillator area. Crystal startup margin, load capacitance, and ESR directly affect timekeeping accuracy and should be validated on the final board.
Design the primary and backup paths separately so a 3 V backup cell cannot receive reverse voltage from the 5 V rail. Verify the backup-switchover threshold, VOUT monitoring behavior, and SRAM write-control timing against the manufacturer datasheet. Include local bulk and bypass capacitance near the supply pins, and validate startup and power-loss transitions across the full 4.5 V to 5.5 V operating range.
Do not substitute the surface-mount BQ4845S-A4NTR directly for the BQ4845YP-A4E3 because the packages and footprints differ. Also avoid assuming that every BQ4845 suffix has identical temperature, qualification, and ordering attributes. Before substitution, compare pin names, register behavior, reset timing, watchdog limits, oscillator loading, and backup current using the manufacturer datasheet for each exact MPN.
Thông tin tuân thủ
The verified Ampheo product snippet identifies the BQ4845YP-A4E3 as RoHS compliant. No verified REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals statements were supplied.
