BTS722204ESPXUMA1 - 4-Ch SPI High-Side Switch | Infineon
MPN: BTS722204ESPXUMA1 ✓ Hoạt độngBTS722204ESPXUMA1 Tóm tắt
Background: A high-side power switch (also called a smart high-side switch, semiconductor relay, or solid-state fuse) is a power-management semiconductor that sits between the battery/load supply and the load, replacing a discrete MOSFET plus fuse plus relay combination. Programmable logic-level inputs (here, 3.3 V and 5 V compatible) turn the channels on; integrated protection handles overcurrent, overtemperature, short-circuit, reverse battery and ground-loss events. High-side switches belong to the broader hierarchy: power switch -> load driver -> power management IC -> semiconductor.
Key features of the BTS722204ESPXUMA1 include daisy-chain capable SPI for multi-device addressing, slew-rate control for electromagnetic-compatibility tuning, ReverseON operation that keeps the channels conducting during reverse polarity (low power dissipation in that mode), programmable restart after overcurrent, and absolute/dynamic temperature limitation with controlled restart. The SPI also reports open-load, short-to-ground and short-to-battery diagnostics per channel.
Architecturally, each channel is built around an N-channel vertical power MOSFET driven by a charge pump, with the SPI block handling configuration, fault flags and daisy-chain pass-through. Channels 0/1 are rated 4 A (lower RDS(on) region of about 13.5 mOhm) and channels 2/3 are rated 7 A (RDS(on) about 5.5 mOhm), giving designers flexibility to pair heavier loads (H-bridge half-bridges, pumps) with lighter loads (lamps, LEDs) on one IC.
Typical applications include body-control modules, front and rear lighting, seat-control and mirror-adjust loads, HVAC blowers, and any 12 V automotive load requiring protected switching with diagnostic feedback. Use the BTS722204ESPXUMA1 when you need per-channel current telemetry, low quiescent current in standby, and AEC-Q100-grade robustness in a small PG-TSDSO-24-32 footprint.
Design consideration: because the device is SPI-controlled, the host microcontroller must reserve one SPI peripheral and three GPIO pins (CS, SCLK, SDO); for multi-IC harnesses enable the daisy-chain mode to share one CS line. Decoupling, ground returns and thermal copper area under the exposed pad are critical for sustaining the 7 A channels.
This page synthesises current distributor pricing, drop-in same-package alternatives, and practical design notes that are not present in the manufacturer datasheet.
Bộ thay thế dễ dàng lắp đặt cho BTS722204ESPXUMA1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với BTS722204ESPXUMA1 (cùng hình factor và footprint) — khác nhau ở Package, Number of Channels, Product Type, Protection Features, Family.
BTS72220-4ESP
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
BTG7003A1EPWXUMA2
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BTS70402EPGXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BTS710336ESAXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →TLE94104EPXUMA1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →BTS722204ESPXUMA1 Tỷ lệ tối đa & tính chất điện
| Product Type | Multichannel high-side power switch with SPI |
| Family | SPOC +2 (SMART7) |
| Number of Channels | 4 |
| Channel 0 Rated Current | 4 A |
| Channel 1 Rated Current | 4 A |
| Channel 2 Rated Current | 7 A |
| Channel 3 Rated Current | 7 A |
| On-Resistance (low-RDS(on) channels) | 5.5 mOhm typical |
| On-Resistance (high-RDS(on) channels) | 13.5 mOhm typical |
| Giao diện | SPI, daisy-chain capable |
| Logic Input Compatibility | 3.3 V and 5 V microcontrollers |
| Protection Features | Overcurrent, overtemperature, short-circuit, reverse polarity, ReverseON, programmable restart |
| Diagnostic Outputs | Open-load, short-to-GND, short-to-Vbat, overtemperature flags via SPI |
| Hộp | PG-TSDSO-24-32 (exposed pad) |
| Kiểu lắp đặt | Surface Mount |
| Nhiệt độ hoạt động | -40C to +150C (automotive AEC-Q100 grade expected) |
| AEC-Q100 | Qualified (automotive grade, per family) |
| Trạng thái RoHS | Compliant |
Hướng dẫn cấu hình chân BTS722204ESPXUMA1 pg-tsdso-24-32 (exposed pad)
Cấu hình chân cho BTS722204ESPXUMA1 (pg-tsdso-24-32 (exposed pad) gói). Động cơ điện này có chân cổng, nguồn và đầu ra. Đối với các gói không phân極, tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết hướng dẫn chính xác của chân 1 và chi tiết về vân footprint. Các ứng dụng phổ biến bao gồm thiết kế nguồn cung cấp điện, điều khiển động cơ và chuyển đổi tải.
Không có dữ liệu chân cụ thể sẵn có cho BTS722204ESPXUMA1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
BTS722204ESPXUMA1 phù hợp cho 6 Áp dụngs: Automotive Body Control Module (BCM), Front and Rear Automotive Lighting, HVAC Blower and Fan Drivers, Power Seat and Power Mirror Adjusters, Wiper and Washer Pump Control, Industrial 12 V / 24 V Relay Replacement.
Automotive Body Control Module (BCM)
The BTS722204ESPXUMA1 is well suited to driving mixed automotive loads in a body-control module where per-channel diagnostics and AEC-Q100 robustness are required. Its four channels - two at 4 A and two at 7 A - cover lamps, mirror adjusters, seat motors and HVAC blowers from one PG-TSDSO-24-32 IC. The integrated SPI with daisy-chain support lets the BCM microcontroller poll open-load, short-to-GND and short-to-Vbat status for each output, supporting ISO 26262 functional-safety diagnostic coverage goals. ReverseON keeps the channels conducting during reverse-battery events without dissipating full load current, and programmable restart after overcurrent lets the host choose between latch-off and auto-retry strategies.
Được đề xuất
Front and Rear Automotive Lighting
For driving halogen, incandescent or LED front and rear lamp clusters, the BTS722204ESPXUMA1's 7 A channels at 5.5 mOhm RDS(on) deliver low conduction loss across the harness. The two lower-rated 4 A channels can run smaller lamps or LED driver stages, while the two 7 A channels can drive high-beam, low-beam or tail-lamp loads directly. Slew-rate control limits the di/dt during turn-on, reducing EMC emissions that would otherwise require additional filtering. Diagnostic feedback via SPI flags lamp-out conditions (open load) directly to the BCM without extra current-sense circuitry, lowering BOM cost and PCB area compared with discrete MOSFET solutions.
Được đề xuất
HVAC Blower and Fan Drivers
The BTS722204ESPXUMA1's 7 A channels easily handle HVAC blowers and radiator fans used in 12 V automotive platforms. Each channel's integrated thermal shutdown and dynamic temperature limitation with controlled restart protect the device against stalled-rotor conditions without host intervention. RDS(on) of 5.5 mOhm on the 7 A channels keeps conduction losses below 0.3 W at full load, so the PG-TSDSO-24-32 exposed pad can dissipate the heat into a moderate copper pour on the PCB. Overcurrent protection with programmable restart allows the system to clear a temporary stall (such as ice in the blower) and resume operation once the fault clears, improving perceived quality versus latch-off behavior.
Được đề xuất
Power Seat and Power Mirror Adjusters
Power-seat and power-mirror adjusters need four to six protected half-bridge outputs and per-channel current limiting - exactly what the BTS722204ESPXUMA1 family addresses. While the BTS722204ESPXUMA1 itself is a high-side switch, two devices can be combined to form four half-bridges (one high-side channel per direction), or it can be paired with companion Infineon low-side switches for full H-bridge motor control. The 4 A and 7 A channel split matches typical seat-motor current profiles, and SPI-based stall detection lets the host recognise end-of-travel and jam conditions in real time, improving safety and customer experience.
Được đề xuất
Wiper and Washer Pump Control
Wiper motors and washer pumps benefit from the BTS722204ESPXUMA1's overcurrent and short-circuit protection. The 7 A channel handles intermittent wiper-motor inrush while the 4 A channel can drive the washer pump. ReverseON operation protects the IC and harness during jump-start or reverse-battery service events, and the daisy-chain SPI allows multiple BTS722204ESPXUMA1 devices to share one CS line in large BCMs with many loads. Programmable restart lets the system automatically retry after a stalled-wiper event, while SPI fault flags log the failure for service diagnostics.
Được đề xuất
Industrial 12 V / 24 V Relay Replacement
Outside automotive, the BTS722204ESPXUMA1 can replace electromechanical relays in industrial 12 V systems that need solid-state reliability, silent switching, and integrated diagnostics. The 4 A/4 A/7 A/7 A channel ratings cover solenoids, small motors and indicator loads, while the SPI diagnostic interface can be driven by an industrial MCU or even an SPI-to-USB bridge for test and configuration. AEC-Q100-grade robustness gives the device wider temperature margin than typical industrial-grade parts, useful in unenclosed cabinets or outdoor enclosures where the operating temperature can exceed 85 C ambient.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho BTS722204ESPXUMA1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | BTS72220-4ESP | BTG7003A1EPWXUMA2 | BTS70402EPGXUMA1 | BTS710336ESAXUMA1 | TLE94104EPXUMA1 |
|---|---|---|---|---|---|---|
| Brand | Infineon | Infineon | Infineon | Infineon | Infineon | Infineon |
| Package | PG-TSDSO-24-32 | PG-TSDSO-24-32 (same) | PG-TSDSP-16-1 | PG-TSDSP-14-1 | PG-TSDSP-16-1 | PG-TSDSP-24-1 |
| AEC-Q100 Grade | Qualified (family) | Qualified (family) | Qualified (family) | Qualified (family) | Qualified (family) | Qualified (family) |
| Packaging | Tape & Reel (XUMA1) | Tray (no XUMA1) | Tape & Reel (XUMA2) | Tape & Reel (XUMA1) | Tape & Reel (XUMA1) | Tape & Reel (XUMA1) |
Bảo phân biệt quan trọng
- Daisy-chain SPI for multi-IC BCMs (vsClassic BTS716GP two-channel high-side switch)
- Mixed 4 A/4 A/7 A/7 A current ratings (vsBTS70402EPGXUMA1 (2-channel))
- ReverseON low-power reverse-polarity operation (vsOlder BTS724L1 (no ReverseON))
Ghi chú thiết kế
Estimated: at Vbb=14 V, VOUT=14 V (full-on lamp) and I=7 A on the low-RDS(on) channel, dissipation is P = I^2 * RDS(on) = 7^2 * 0.0055 = 0.27 W per channel; with all four channels at full load the package dissipates around 1 W. Solder the exposed pad to at least 1 square inch of 2 oz copper to keep the junction below 150 C ambient-rated limit. If two channels run continuous 7 A simultaneously, place thermal vias under the exposed pad to the inner PCB plane and consider adding a small heat-spreader copper pour on the opposite PCB side.
Place the SPI trace impedance-matched (typically 50 ohm single-ended with a series 22-33 ohm resistor at SDO) to avoid ringing on the SDO line. The daisy-chain SDO-to-SDI link should be kept short (<50 mm) and routed away from the OUT traces to prevent capacitive coupling of high-di/dt load transients into the SPI logic. Add a 100 nF decoupling capacitor as close as possible to the Vbb pin and a bulk 10-47 uF electrolytic or polymer capacitor on the same Vbb node to absorb load-dump transients.
Do not float the CSN pin - tie it to the MCU CS GPIO so the device is not unintentionally selected on power-up and drives SDO low, blocking other devices on a shared SPI bus. Ensure the MCU drives SCLK, SDI and CSN as push-pull outputs; open-drain configuration can cause spurious clocks and latched fault states. When using daisy-chain mode, verify that the number of cascaded devices multiplied by 8 bits per device fits the host SPI peripheral's programmable data length (some MCUs cap at 16 or 32 bits); use two SPI transactions if the chain exceeds the MCU's single-transfer length.
Slew-rate control is programmable per channel via SPI on the BTS722204ESPXUMA1; for EMC-sensitive lamp loads choose the slowest slew rate that meets the application's turn-on timing requirement (typically 200-500 us rise time). Faster slew rates reduce switching loss but increase radiated EMI on the OUT traces - the SPOC +2 family datasheet's EMC reference layout shows ferrite beads and Y-capacitors that can be omitted when using the slower default slew rate.
Thông tin tuân thủ
AEC-Q100 qualified per Infineon SPOC +2 family datasheet (Infineon-BTS72220-4ESP-DS-v01_00-EN). RoHS and REACH compliant per distributor listings. Halogen-free status not explicitly stated in the provided web data - confirm via the Infineon material declaration if required for your design.
