C8051F369-GM - 50MHz 8-bit MCU with ADC/DAC | Silicon Labs
MPN: C8051F369-GM ✓ Hoạt độngC8051F369-GM Tóm tắt
A mixed-signal microcontroller such as the C8051F369-GM belongs to the embedded-control hierarchy that includes MCU, microprocessor, mixed-signal IC, and semiconductor. Its 8051-compatible core combines flash-based program storage with on-chip analog peripherals, allowing a design to measure or generate analog signals while executing control software locally. The 28-QFN package also includes an exposed pad for improved thermal transfer on a PCB.
Key specifications include a 50MHz maximum clock, 16KB flash memory, 1KB RAM, a 2.7V to 3.6V supply range, and an operating temperature range of -40C to 85C. The device is identified as an 8-bit microcontroller in the C8051F36x series, with an internal oscillator and flash program memory. Integrated conversion features include a 10-bit ADC rated for up to 200ksps in the relevant family configurations and a 10-bit DAC.
The architecture supports mixed-signal acquisition and output alongside serial interfaces including SMBus or I2C, SPI, and UART/USART. This combination is useful when a controller must supervise sensors, control actuators, communicate with a host processor, and perform local calculations. The C8051F36x family is associated with Silicon Labs in-system-programmable flash MCU products, allowing firmware development and production programming workflows.
Typical applications include industrial sensor nodes, building automation modules, motor and power-control boards, compact data-acquisition units, consumer accessories, and embedded communication equipment. The 50MHz operating speed provides useful headroom for protocol handling and control-loop execution, while the 16KB flash and 1KB RAM keep the device appropriate for focused rather than general-purpose embedded workloads.
When laying out a board, reserve the exposed pad and provide adequate copper for heat dissipation. Keep analog input and reference connections short, use a clean supply path around the analog peripherals, and follow the manufacturer pin-description table when assigning PCB tracks. For replacement decisions, verify the exact package suffix, temperature grade, flash size, peripheral set, and firmware compatibility rather than relying only on the C8051F36x family name.
Bộ thay thế dễ dàng lắp đặt cho C8051F369-GM — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
C8051F369-C-GM
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F369-C-GMR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F367-GM
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F367-C-GM
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F367-C-GMR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F369-GM Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit mixed-signal flash microcontroller |
| Core | C8051F36x 8051-compatible core |
| Maximum Clock | 50 MHz |
| Bề rộng đường dữ liệu | 8 bit |
| Program Memory | 16 KB flash, 16K x 8 organization |
| RAM | 1 KB, 1K x 8 organization |
| Điện áp cung cấp | 2.7V to 3.6V |
| ADC | 10-bit, up to 200 ksps |
| ADC Input Configuration | Up to 21 external single-ended or differential inputs |
| DAC | 10-bit |
| Điện áp tham chiếu | Internal VREF, external pin, or VDD |
| Serial Interfaces | SMBus or I2C, SPI, UART/USART |
| Nhiệt độ hoạt động | -40C to 85C |
| Hộp | 28-QFN, 5x5 mm, exposed pad |
| Kiểu lắp đặt | Surface mount |
| Oscillator Type | Internal |
Hướng dẫn cấu hình chân C8051F369-GM 28-qfn, 5x5 mm, exposed pad
Cấu hình chân cho C8051F369-GM (28-qfn, 5x5 mm, exposed pad gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho C8051F369-GM.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
C8051F369-GM phù hợp cho 6 Áp dụngs: Industrial Sensor Acquisition, Building Automation Controller, Compact Data-Acquisition Unit, Motor and Power-Control Board, Connected Equipment Module, Consumer Accessory Controller.
Industrial Sensor Acquisition
The C8051F369-GM fits compact sensor nodes that must acquire analog measurements while managing local control and communications. Its 10-bit ADC supports rates up to 200ksps in applicable family configurations, and the 50MHz core leaves processing headroom for filtering, calibration, and protocol handling. The 16KB flash accommodates focused firmware, while 1KB RAM supports short working buffers. Place the MCU in a 28-QFN 5x5mm footprint with the exposed pad connected to a solid ground plane. For industrial deployments, the -40C to 85C rating is useful, but the final enclosure, sensor accuracy, and supply tolerance must be validated as a complete system.
Được đề xuất
Building Automation Controller
The C8051F369-GM is appropriate for small building-automation modules that combine sensor inputs, actuator control, and a low-speed serial network. Its 50MHz 8051-compatible core can execute protocol tasks and control logic, while the 10-bit ADC handles analog environmental or occupancy feedback. The 2.7V to 3.6V supply range fits powered sensor and relay modules. Firmware can use the internal oscillator to reduce external clock-component count. Design the PCB with short analog traces, stable reference routing, and careful separation between digital switching nodes and sensitive measurement inputs. Because the 28-QFN exposed pad needs reliable thermal and ground connectivity, follow the manufacturer land pattern exactly.
Được đề xuất
Compact Data-Acquisition Unit
The C8051F369-GM supports compact data-acquisition designs that need mixed measurement and embedded control without a separate analog processor. The 10-bit ADC can sample at up to 200ksps in relevant configurations, and the 50MHz core can manage sampling timing, basic filtering, and data transfer. Its 16KB flash and 1KB RAM are best suited to short acquisition buffers and focused algorithms rather than large offline storage. The 10-bit DAC can provide a reference or test output where the application requires it. Use controlled-reference routing and quiet supply return paths to maximize measurement repeatability. The 28-QFN footprint reduces board area while making thermal-pad vias and analog layout quality especially important.
Được đề xuất
Motor and Power-Control Board
The C8051F369-GM can serve as the supervisory controller in a compact motor-control or power-sequencing board. At 50MHz, its 8-bit core can execute timing logic, monitor analog feedback, and coordinate communications while external power devices perform the high-energy switching. The 10-bit ADC is useful for current, voltage, or position feedback, and the 10-bit DAC may support control references or test functions. The 16KB flash and 1KB RAM suit focused supervisory code. Keep the MCU away from high-current switching paths, provide local supply bypassing, and route exposed-pad vias into the ground plane. Firmware and hardware must also validate shutdown behavior under fault conditions.
Được đề xuất
Connected Equipment Module
The C8051F369-GM fits connected equipment modules that need local control plus UART/USART, SPI, or SMBus/I2C connectivity. The 50MHz core provides sufficient throughput for protocol framing, state management, and periodic data acquisition, while 16KB flash holds a compact application program. Its 28-QFN 5x5mm package preserves board area in small industrial or consumer products. Use separate routing discipline for serial signals and analog inputs, and place bypass capacitance close to supply pins according to the manufacturer guidance. The -40C to 85C operating range supports many deployed environments. Before product release, verify startup timing, bus levels, and firmware behavior with the exact production suffix.
Được đề xuất
Consumer Accessory Controller
The C8051F369-GM is practical for compact consumer accessories requiring a low-power MCU, local analog control, and serial host communication. Its 2.7V to 3.6V operating range, 50MHz core, and 16KB flash provide enough capability for user-interface state, sensor handling, and accessory control. The 10-bit ADC can monitor simple analog inputs, while the DAC can generate low-level analog signals where required. The small 28-QFN footprint is useful in space-constrained products. Keep the exposed pad tied to the ground network, isolate analog inputs from fast digital edges, and validate standby behavior and startup timing. For safety or regulatory-sensitive functions, add the required fault detection and energy-control measures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho C8051F369-GM — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | C8051F369-C-GM | C8051F369-C-GMR | C8051F367-GM | C8051F367-C-GM | C8051F367-C-GMR |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 28-QFN (5x5) | 28-QFN (5x5) | 28-QFN (5x5) | 28-QFN (5x5) | 28-QFN (5x5) | 28-QFN (5x5) |
| Core | C8051F36x 8051-compatible core | C8051F36x 8051-compatible core | C8051F36x 8051-compatible core | C8051F36x 8051-compatible core | C8051F36x 8051-compatible core | C8051F36x 8051-compatible core |
| Maximum Clock | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| ADC and DAC | 10-bit ADC and 10-bit DAC | 10-bit ADC and 10-bit DAC | 10-bit ADC and 10-bit DAC | Device-specific mixed-signal resources | Device-specific mixed-signal resources | Device-specific mixed-signal resources |
| Serial Interfaces | SMBus or I2C, SPI, UART/USART | SMBus or I2C, SPI, UART/USART | SMBus or I2C, SPI, UART/USART | Device-specific serial interface configuration | Device-specific serial interface configuration | Device-specific serial interface configuration |
Bảo phân biệt quan trọng
- Exact 50MHz configuration with 16KB flash and 1KB RAM (vsC8051F367-GM)
- Integrated 10-bit DAC alongside the 10-bit ADC (vsC8051F367-GM)
- Same package family with a broad 2.7V to 3.6V supply range (vsC8051F369-C-GM)
- Three documented serial interface types (vsC8051F367-C-GM)
Ghi chú thiết kế
Use the manufacturer’s 28-QFN land pattern and expose the thermal pad to the PCB with a recommended via arrangement. Keep the exposed pad tied to the same low-impedance ground network used by the supply pins. A 5x5mm footprint leaves little clearance for improvised routing, so establish the pin escape strategy before placing analog and serial signals.
Route analog inputs and the reference connection away from UART, SPI, and other switching edges. The 10-bit ADC can acquire samples up to 200ksps in applicable family configurations, but sampling rate alone does not ensure accuracy; input settling, source impedance, reference stability, and ground return paths determine practical performance. Follow the recommended bypass and analog-layout guidance in the datasheet.
Do not treat every C8051F36x suffix as electrically identical. Confirm the pin table, ADC channel count, DAC availability, memory configuration, temperature grade, and package suffix before substituting. Firmware built for C8051F369 should be validated against the candidate device’s peripheral map, particularly when moving to a C8051F367 variant.
Keep the 2.7V to 3.6V operating range in mind when designing the power rail, including startup tolerance and regulator accuracy. Place decoupling capacitance close to the supply and ground pins and provide a low-impedance return path for the exposed pad. Analog accuracy can depend on reference and supply behavior, so evaluate the complete rail rather than only its nominal voltage.
Thông tin tuân thủ
No explicit RoHS, REACH, lead-free, halogen-free, or conflict-minerals status was identified for this exact MPN. AEC-Q100 is not applicable to this general-purpose MCU classification.