C8051F382-GQ - 50MHz USB Flash MCU | Silicon Labs
MPN: C8051F382-GQ ✓ Hoạt độngC8051F382-GQ Tóm tắt
A microcontroller is a programmable semiconductor that integrates a CPU core, memory, peripherals, and communication interfaces onto one device. The C8051F38x family belongs to the 8-bit microcontroller hierarchy and combines a 8051-compatible CISC architecture with flash memory, analog conversion, and USB connectivity. Silicon Labs describes the family as a pin- and code-compatible replacement for the C8051F34x family in most applications.
The C8051F382-GQ provides 32 KB of flash for firmware and 2.25K x 8 bits of internal RAM, reducing the need for external program-memory devices. Its full-speed USB interface supports USB-connected peripheral and control products, while the listed analog capability includes a built-in multiplexer and conversion rates up to 500 ksps. The 2.7 V to 5.25 V supply range permits operation from regulated 3.3 V or 5 V system rails.
The device uses the 8051 CISC architecture and operates at up to 50 MHz, corresponding to the listed 48 MIPS performance figure. A 48-pin TQFP package provides a conventional fine-pitch surface-mount option for industrial and embedded control boards. Because the MCU combines USB, flash, RAM, timers, and analog functions, firmware can remain compact while designers minimize the number of external components.
Typical uses include USB data acquisition, industrial control interfaces, USB-to-serial equipment, human-interface devices, embedded instrumentation, and portable USB-powered products. The integrated analog conversion capability is useful for monitoring sensors through the internal multiplexer, while full-speed USB simplifies host connectivity over a standard peripheral port.
PCB design should reserve the full 48-pin TQFP land pattern, route USB D+ and D- as a controlled impedance differential pair, and place decoupling capacitors close to the supply pins. Firmware migration requires checking peripheral availability, interrupt-vector behavior, clock configuration, and USB firmware compatibility rather than relying only on package matching.
This page combines the device specifications, verified family relationships, practical application guidance, package constraints, and engineering-focused replacement analysis to support faster component selection and board planning.
Bộ thay thế dễ dàng lắp đặt cho C8051F382-GQ — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với C8051F382-GQ (cùng hình factor và footprint) — khác nhau ở Package, Product Type.
C8051F380-GQ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →C8051F383-GQ
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
C8051F384-GQ
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →C8051F38C-GQ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F387-GQ
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
C8051F382-GQ Tỷ lệ tối đa & tính chất điện
| Product Type | 8-bit Flash USB Microcontroller |
| Series | C8051F38x |
| CPU Architecture | 8051-compatible CISC |
| Tần số xung maksimum | 50 MHz |
| Maximum Instruction Rate | 48 MIPS |
| Program Flash Memory | 32 KB (32K x 8 bits) |
| Internal RAM | 2.25K x 8 bits |
| USB Interface | Full-speed USB |
| Analog Conversion Rate | Up to 500 ksps |
| Analog Multiplexer | Built-in single-ended analog multiplexer |
| Supply Voltage Range | 2.7 V to 5.25 V |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Hộp | 48-pin TQFP (7 x 7 mm) |
| Kiểu lắp đặt | Surface Mount |
| Factory Pack Quantity | 1250 units |
Hướng dẫn cấu hình chân C8051F382-GQ 48-pin tqfp (7 x 7 mm)
Cấu hình chân cho C8051F382-GQ (48-pin tqfp (7 x 7 mm) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho C8051F382-GQ.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
C8051F382-GQ phù hợp cho 6 Áp dụngs: USB Data-Acquisition Controller, Industrial USB Sensor Interface, USB Human-Interface Device, USB-to-Serial Embedded Bridge, Portable USB-Powered Test Instrument, Embedded Control and Monitoring Node.
USB Data-Acquisition Controller
The C8051F382-GQ fits a USB data-acquisition controller that combines local sensor conditioning, digital processing, and host communication in one device. Its 50 MHz 8051-compatible core and 48 MIPS operating rate provide timing capacity for sampling control and USB service tasks, while 32 KB of flash stores application firmware and descriptors. The built-in analog multiplexer and conversion capability up to 500 ksps support multiplexed measurement channels without requiring a separate converter. Full-speed USB simplifies attachment to a computer or embedded host. Design the analog front end for the selected voltage range, protect analog inputs against transients, and validate sampling accuracy and USB enumeration timing with the production firmware.
Được đề xuất
Industrial USB Sensor Interface
The C8051F382-GQ is appropriate for an industrial USB sensor interface that must collect measurements, apply local logic, and present a standard host interface. Its operating range of 2.7 V to 5.25 V supports common regulated industrial rails, while its -40 °C to +85 °C rating accommodates temperature-controlled equipment. The integrated analog multiplexer helps reduce external component count when several sensor signals must be scanned. Firmware can run directly from 32 KB of flash, and 2.25K x 8 bits of RAM supports acquisition buffers and protocol state. Designers should calibrate each channel, isolate noisy motors or relays from analog circuitry, and confirm that the enclosure and USB connector preserve reliable communications in the intended environment.
Được đề xuất
USB Human-Interface Device
The C8051F382-GQ can implement a USB human-interface device such as a control panel, configuration interface, or specialized input device. Full-speed USB provides a direct host connection, while the 50 MHz core allows responsive debouncing, status updates, and protocol handling. The 32 KB flash capacity is useful for compact firmware containing USB descriptors, HID reports, configuration logic, and upgrade routines. Its 48-pin TQFP package is appropriate for multilayer or densely routed boards, but the 7 x 7 mm body requires careful fanout and paste inspection. Validate enumeration across the target operating systems, confirm report timing, and keep ESD protection close to the connector while preserving controlled-impedance USB routing.
Được đề xuất
USB-to-Serial Embedded Bridge
The C8051F382-GQ is well suited to a USB-to-serial bridge that translates between a full-speed USB host and an embedded UART interface. Its 8051-compatible core can support protocol conversion, framing, buffering, and device management, while 32 KB of flash is sufficient for many compact bridge designs. The 2.7 V to 5.25 V operating range accommodates both 3.3 V and 5 V interface environments when levels are selected correctly. Because the part integrates USB and analog functions, firmware can also add local control or monitoring. Use a level translator for mismatched serial voltages, define USB descriptors carefully, and test throughput, suspend behavior, and bus-powered current against the complete peripheral load.
Được đề xuất
Portable USB-Powered Test Instrument
The C8051F382-GQ supports a portable USB-powered test instrument where a compact controller, measurement function, and USB connection are required. Its 50 MHz processing rate supports deterministic control and data handling, and 32 KB of flash accommodates firmware for a focused measurement product. The internal analog multiplexer and 500 ksps conversion capability can support fast sampled measurements when the analog front end has suitable bandwidth and settling behavior. Operation from 2.7 V permits flexible use of low-voltage power systems. Designers should budget regulator dropout and transient response, limit analog input overdrive, and test enumeration and measurement accuracy with the final enclosure, cable, and power source.
Được đề xuất
Embedded Control and Monitoring Node
The C8051F382-GQ can serve as the central controller in a compact monitoring node that reads analog inputs, evaluates thresholds, records events, and exposes status through USB. Its integrated 32 KB flash reduces external program-memory requirements, and its 50 MHz core leaves processing headroom for diagnostics and communication routines. The -40 °C to +85 °C rating supports industrial and commercial equipment, while 2.7 V to 5.25 V operation provides flexibility across regulated rails. Keep sensitive analog paths away from USB and switching traces, provide local decoupling at the supply pins, and include recovery logic for brownout or disconnected-bus conditions so the node returns to a predictable state after power restoration.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho C8051F382-GQ — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | C8051F380-GQ | C8051F383-GQ | C8051F384-GQ | C8051F38C-GQ | C8051F387-GQ |
|---|---|---|---|---|---|---|
| Brand | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs | Silicon Labs |
| Package | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) | 48-pin TQFP (7 x 7 mm) |
| CPU Architecture | 8-bit 8051-compatible CISC | 8-bit 8051-compatible CISC | 8-bit 8051-compatible CISC | 8-bit 8051-compatible CISC | 8-bit 8051-compatible CISC | 8-bit 8051-compatible CISC |
| Maximum Clock Frequency | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz | 50 MHz |
| Instruction Rate | 48 MIPS | 48 MIPS | 48 MIPS | 48 MIPS | 48 MIPS | 48 MIPS |
| Program Flash Memory | 32 KB | 16 KB | 64 KB | 64 KB | 64 KB | 64 KB |
| USB Interface | Full-speed USB | Full-speed USB | Full-speed USB | Full-speed USB | Full-speed USB | Full-speed USB |
| Supply Voltage Range | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V | 2.7 V to 5.25 V |
| Operating Temperature Range | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C | -40 °C to +85 °C |
Bảo phân biệt quan trọng
- Balanced memory capacity for compact USB firmware (vsC8051F380-GQ)
- Lower flash burden than larger same-family devices (vsC8051F384-GQ)
- Full-speed USB and analog conversion in one MCU (vsC8051F387-GQ)
Ghi chú thiết kế
Route USB D+ and D- as a short, continuous differential pair with matched impedance to the connector or transceiver. Avoid stubs, test pads that lack proper termination, and plane splits beneath the pair. Keep the MCU and USB-related decoupling close to their pins, while separating USB clock and data routing from analog inputs and switching-supply traces.
The 48-pin TQFP has fine-pitch leads on all four sides, so use a land pattern that matches the manufacturer's package drawing and verify solder-paste volume and stencil apertures before production. Preserve the pin-1 orientation, inspect lead coplanarity, and avoid placing tall components that can interfere with inspection or rework. Confirm exposed-pad and thermal requirements from the package drawing if the selected footprint includes a thermal pad.
Do not treat another C8051F38x member as an automatic substitute merely because it uses the same TQFP footprint. Compare flash capacity, RAM, USB behavior, analog channels, clocking, interrupt assignments, and peripheral availability in the device-specific documentation. The family relationship supports hardware reuse in many designs, but firmware and boot-code compatibility must be verified before releasing a substitute to production.
Keep the operating voltage within 2.7 V to 5.25 V and account for startup, USB attach, and analog-reference settling when selecting the supply. Place the required bypass network at the power pins and use a regulator with adequate transient response for the complete USB-powered load. Verify brownout behavior, reset timing, and bus-powered current before the board is connected to a host.
Thông tin tuân thủ
No explicit RoHS, REACH, AEC-Q100, lead-free, halogen-free, or conflict-minerals declarations were identified for this ordering code. Confirm compliance for the exact production lot with the manufacturer.