DP83848EVVX/NOPB 10/100 Ethernet PHY | Texas Instruments
MPN: DP83848EVVX/NOPB ✓ Hoạt độngDP83848EVVX/NOPB Tóm tắt
An Ethernet PHY is a semiconductor that converts digital data supplied by a MAC or Ethernet controller into electrical signaling for a wired network and receives incoming network signals for conversion back into digital data. In the hierarchy of electronic components, the DP83848EVVX/NOPB is an Ethernet interface transceiver, a network interface IC, and ultimately a semiconductor. Placing this function on a dedicated PHY can reduce the complexity of the host controller and support copper-based 10BASE-T and 100BASE-TX network connections.
The device is identified as a single transceiver with MII and RMII support. MII provides a parallel data interface between the PHY and a network controller, while RMII uses a reduced pin interface that can simplify connections with devices providing an RMII media-access controller. These interfaces make the DP83848EVVX/NOPB relevant to designs operating at either 10 Mbit/s or 100 Mbit/s, depending on the controller, network, and PHY configuration.
The 48-LQFP package exposes the complete transceiver interface and associated control functions in a standardized 7 x 7 mm footprint. The industrial-grade family listing identifies an operating temperature range of -40 °C to +85 °C for DP83848IVVX/NOPB, but the exact electrical limits and environmental ratings for every DP83848EVVX/NOPB variant must be confirmed in its manufacturer ordering information. The DP83848I family also includes SNI and JTAG support on identified variants.
Typical applications include industrial Ethernet controllers, factory automation equipment, embedded data-acquisition systems, network-interface adapters, instrumentation, and communications equipment. In each case, the PHY sits between the digital controller and the physical network medium, allowing the controller to use a digital MII or RMII interface while the DP83848EVVX/NOPB handles the network-facing signaling function.
PCB design should prioritize clean separation between digital interface traces and analog network-facing circuitry. The manufacturer datasheet and pin-description table should be used to assign supply, ground, clock, reset, management-interface, and media connections. Validate magnetics, termination, cable reach, link behavior, and electromagnetic-emissions requirements in the final board design rather than relying on generic Ethernet guidance alone.
This product summary combines package, interface, speed, and family-level operating information with engineering-focused application guidance and alternative-selection context. It is intended to help designers determine whether the DP83848EVVX/NOPB fits an existing PCB and network architecture before completing detailed signal-integrity, thermal, and regulatory verification.
Bộ thay thế dễ dàng lắp đặt cho DP83848EVVX/NOPB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DP83848EVVX/NOPB (cùng hình factor và footprint) — khác nhau ở Product Type, Auto-Negotiation, Data Rate, JTAG Support, Operating Temperature.
DP83848IVVX/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DP83848VYB/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DP83848IVV/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DP83848EVVX/NOPB Thông số kỹ thuật
| Product Type | Ethernet PHY transceiver |
| Tốc độ dữ liệu | 10 Mbit/s and 100 Mbit/s |
| Transceiver Configuration | 1/1 transceiver |
| Digital Interface | MII and RMII |
| Package Type | 48-LQFP |
| Package Dimensions | 7 mm x 7 mm |
| Số chân | 48 pins |
| Kiểu lắp đặt | Surface mount |
| Family Operating Temperature | -40 °C to +85 °C for DP83848IVVX/NOPB |
| Family SNI Support | Supported on DP83848IVVX/NOPB |
| Family JTAG Support | Supported on DP83848IVVX/NOPB |
| Ethernet Media | Copper 10BASE-T and 100BASE-TX |
Hướng dẫn cấu hình chân DP83848EVVX/NOPB 7 mm x 7 mm
Cấu hình chân cho DP83848EVVX/NOPB (7 mm x 7 mm gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DP83848EVVX/NOPB.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DP83848EVVX/NOPB phù hợp cho 6 Áp dụngs: Industrial Automation Controller, Embedded Network Data Acquisition, Test and Measurement Instrument, Factory Sensor Gateway, Communications Appliance, Network Interface Adapter.
Industrial Automation Controller
The DP83848EVVX/NOPB fits an industrial automation controller that connects a digital controller or MCU to a 10/100-Mbps copper Ethernet network. Its 10/100-Mbps capability supports both legacy and fast Ethernet network rates, while MII and RMII interfaces let the design choose between a parallel controller connection and a more compact reduced interface. The 48-LQFP package also provides a defined surface-mount footprint for multilayer control boards. Implementation should include manufacturer-recommended power decoupling, controlled clocking, proper reset behavior, and an Ethernet network-isolation or magnetics arrangement appropriate to the installation environment.
Được đề xuất
Embedded Network Data Acquisition
The DP83848EVVX/NOPB is suitable for an embedded data-acquisition unit that must add wired 10/100-Mbps Ethernet without implementing the physical layer in a controller. A host processor or communications controller can connect through MII or RMII while the PHY provides the network-facing transceiver function. This division keeps high-speed digital traffic close to the controller while placing the Ethernet interface in a clearly defined circuit section. For long operating cycles and industrial installations, verify the exact temperature grade, power budget, isolation strategy, and electromagnetic-emissions requirements for the completed product.
Được đề xuất
Test and Measurement Instrument
The DP83848EVVX/NOPB can support Ethernet connectivity in test and measurement equipment that transfers instrument data over a 10/100-Mbps copper network. The selectable MII and RMII interfaces allow the instrument architecture to align with its FPGA, processor, or dedicated communication controller. Its 48-LQFP package is suitable for dense measurement instruments where a functional PHY is needed without relying on an Ethernet controller integrated into the main processing device. Designers should use the manufacturer reference layout, preserve clock and supply integrity, and validate network performance against the instrument's expected data rate and cable environment.
Được đề xuất
Factory Sensor Gateway
A factory sensor gateway can use the DP83848EVVX/NOPB to bridge an embedded host to a 10/100-Mbps Ethernet backbone. The PHY is appropriate when the gateway needs a dedicated copper-network interface and the host supports MII or RMII. Using RMII can reduce the number of digital interface traces, while MII may offer a more parallel connection where routing space is available. The 7 x 7 mm 48-LQFP package leaves room for other sensing and processing functions on a compact board. The final design should account for surge events, cable faults, grounding, and the industrial temperature range required at the installation site.
Được đề xuất
Communications Appliance
The DP83848EVVX/NOPB is applicable to communications appliances that require a dedicated 10/100-Mbps Ethernet physical layer. Depending on the appliance architecture, a communications processor can connect through MII for a parallel interface or RMII for a reduced pin-count interface. The dedicated PHY organization can simplify the processor's media-access responsibilities and provide a clear boundary between digital control logic and copper-network signaling. Engineers should confirm the exact clocking mode, configuration pins, management interface, and power requirements, then validate conducted emissions and network interoperability with the intended equipment ecosystem.
Được đề xuất
Network Interface Adapter
The DP83848EVVX/NOPB can serve as the central Ethernet PHY in a dedicated network-interface adapter for an embedded processor or FPGA platform. The 10/100-Mbps capability allows the adapter to support established copper Ethernet deployments, while MII and RMII provide flexibility in connecting the host logic. The 48-LQFP package offers a standard surface-mount assembly option and a 7 x 7 mm footprint that supports compact adapter boards. A successful implementation requires exact pin assignment, correct magnetics selection, controlled supply sequencing, return-path design, and testing for link establishment under the intended cable length and system noise conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DP83848EVVX/NOPB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DP83848IVVX/NOPB | DP83848VYB/NOPB | DP83848IVV/NOPB |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Package | 48-LQFP (PT), 7 x 7 mm | 48-LQFP (PT), 7 x 7 mm | 48-LQFP | 48-LQFP |
| Ethernet Speed | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s | 10/100 Mbit/s |
| Mounting Type | Surface mount | Surface mount | Surface mount | Surface mount |
| Pin Count | 48 pins | 48 pins | 48 pins | 48 pins |
Bảo phân biệt quan trọng
- Identified SNI and JTAG functionality in the closest documented family option (vsDP83848VYB/NOPB)
- Documented industrial temperature range for the IVVX ordering (vsDP83848IVV/NOPB)
- Direct MII and RMII support for controller integration (vsDP83848VYB/NOPB)
Ghi chú thiết kế
Follow the exact manufacturer application layout for the DP83848EVVX/NOPB, especially the relationship between digital MII or RMII traces, the PHY supply pins, and network-facing circuitry. Keep clock routing short and continuous, provide local supply decoupling at the appropriate pins, and avoid routing high-current or switching signals beneath sensitive media-side nets. Use the package pin description and land pattern for the exact ordering option rather than a generic 48-pin drawing.
Treat the Ethernet media interface as a controlled-impedance and return-path design problem. Match trace geometry to the PCB stack-up, maintain continuous ground references, and verify magnetics, termination, and cable-related component placement against the manufacturer reference design. Validate the design with link-up, packet-error, and conducted-emissions tests because generic Ethernet measurements may not reveal layout-specific coupling or impedance defects.
Do not select an alternative solely because the package name is 48-LQFP. Confirm the controller interface, supported data rates, management functions, configuration straps, reset requirements, clock source, temperature grade, and ordering-specific pin functions. Differences in a single configuration or management signal can prevent a board from operating even when the mechanical footprint matches.
Estimate power dissipation only after confirming the exact supply voltage and operating current for the selected ordering code. Calculate junction temperature from the package thermal characteristics, board copper area, airflow, and adjacent heat sources. If the calculation indicates limited thermal margin, improve copper spreading or reduce nearby power dissipation before increasing the operating temperature or adding enclosure-related temperature rise.
Thông tin tuân thủ
The available product listings do not provide verified compliance conclusions for the exact DP83848EVVX/NOPB ordering code. Check the manufacturer product page and ordering information before making a compliance claim.