DS90CR216MTD-TI - 21-Bit 66MHz LVDS Receiver | Texas Instruments
MPN: DS90CR216MTD-TI ✓ Hoạt độngDS90CR216MTD-TI Tóm tắt
A Channel Link receiver is a high-speed interface circuit that converts parallel source-synchronous data into a differential, clock-forwarded transmission format. In the broader semiconductor hierarchy, it belongs to the interface IC class and uses LVDS signaling to reduce voltage noise, ground-reference requirements, and conductor count compared with an unwrapped parallel bus. The DS90CR216 family is intended for high-speed point-to-point links carrying video, control, or general digital data.
The principal operating characteristics are a +3.3 V supply, a 66 MHz maximum data-strobe frequency, 21 data outputs, and a 48-pin TSSOP package. Its rising-edge data-strobe architecture transfers data on the clock edge for a deterministic sampling arrangement. Differential signaling improves common-mode noise rejection, while the multiplexed LVDS outputs reduce cable size relative to routing 21 separate single-ended signals over a long distance.
The receiver includes 21 parallel data inputs, a differential clock input, differential data and strobe outputs, and power-ground connections. Its electrical performance depends on correct termination, controlled-impedance routing, and stable supply decoupling. Because the data and strobe are transmitted differentially, the interface can reject a substantial amount of common-mode noise while preserving signal timing over a cable or backplane connection.
Typical uses include industrial control links, video transport systems, instrumentation, embedded display connections, and equipment requiring a compact multi-bit differential interface. The 21-bit width is especially useful where transferring each bus as separate single-ended traces would consume excessive board area or cable conductors. Systems must account for propagation delay between the clock and data channels when defining timing margins.
For implementation, follow the pin-description table and recommended external-circuit diagram in the manufacturer datasheet. Place the differential clock and data traces with controlled impedance, keep the input and output interfaces away from high-current switching paths, and validate connector or cable length against the required transfer rate. Do not treat TSSOP lead spacing as a substitute for correct high-speed routing discipline.
This page combines the family-level operating data with practical interface guidance, verified replacement candidates, and a package-aware comparison. It is intended to help engineers identify the correct LVDS Channel Link receiver, verify replacement compatibility, and plan a signal-integrity-conscious implementation rather than relying only on a basic component description.
Bộ thay thế dễ dàng lắp đặt cho DS90CR216MTD-TI — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với DS90CR216MTD-TI (cùng hình factor và footprint) — khác nhau ở Number of Pins, Supply Voltage.
DS90CR216MTDX/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DS90CR216MTD/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90CR216MTDX/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →DS90CR216AMTD/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90CR216AMTDX/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
DS90CR216MTD-TI Thông số kỹ thuật
| Product Type | 21-bit Channel Link LVDS receiver |
| Điện áp cung cấp | +3.3 V |
| Tần số xung maksimum | 66 MHz |
| Number of Data Bits | 21 bits |
| Number of Data Outputs | 21 outputs |
| Data Strobe | Rising edge |
| Interface Standard | LVDS Channel Link |
| Logic Family | LVDS |
| Hộp | 48-pin TSSOP |
| Kiểu lắp đặt | Surface mount |
| Số lượng chân | 48 pins |
Hướng dẫn cấu hình chân DS90CR216MTD-TI 48-pin tssop
Cấu hình chân cho DS90CR216MTD-TI (48-pin tssop gói). Số thứ tự chân, chức năng và sơ đồ kết nối được xác định trong tài liệu thông số kỹ thuật của nhà sản xuất. Tham khảo nó để biết footprint và hướng dẫn hàn chính xác.
Không có dữ liệu chân cụ thể sẵn có cho DS90CR216MTD-TI.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
DS90CR216MTD-TI phù hợp cho 6 Áp dụngs: Industrial Control Data Links, Video Transport Interfaces, Instrumentation and Test Systems, Embedded Display Backplanes, Embedded Control and Data Acquisition, Secure Monitoring and Camera Modules.
Industrial Control Data Links
The DS90CR216MTD-TI fits industrial control systems that must move 21 parallel source-synchronous signals across a compact balanced connection. At up to 66 MHz, the +3.3 V receiver can accept a 21-bit data group and differential clock while delivering differential data and strobe outputs. Differential signaling improves common-mode rejection and reduces the conductor burden associated with 21 single-ended traces. In a controller-to-module architecture, this can simplify cable construction and improve noise immunity, although the design must preserve controlled-impedance routing, provide the required terminations, and verify timing margin across the complete cable and connector path.
Được đề xuất
Video Transport Interfaces
The DS90CR216MTD-TI is appropriate for transporting grouped pixel or control data between video-processing and display modules. Its 21-bit Channel Link width carries substantially more information per transfer cycle than a narrow serial interface, while the 66 MHz clock ceiling supports demanding source-synchronous traffic. The receiver's differential data and strobe outputs are designed for balanced cabling, where common-mode noise rejection and reduced ground-reference dependence are important. Designers should budget cable skew separately from clock frequency because the parallel data group must remain aligned with the forwarded strobe at the far end. Connector geometry, cable loss, and PCB return paths therefore determine the practical usable link distance.
Được đề xuất
Instrumentation and Test Systems
The DS90CR216MTD-TI can serve as the receiving endpoint for instrumentation that collects 21 parallel measurement or control bits and transfers them over a compact differential cable. A 21-bit payload is useful when several converters, switches, or status lines must be transported with a common clock. Operating from +3.3 V supports integration with modern mixed-signal systems, while LVDS signaling reduces susceptibility to common-mode interference encountered near switching power stages or digital equipment. For accurate acquisition, the source must launch valid data at the specified rising-edge strobe, and the complete system should be checked for propagation-delay skew, input threshold behavior, grounding, and connector performance rather than relying only on nominal clock frequency.
Được đề xuất
Embedded Display Backplanes
The DS90CR216MTD-TI is suitable for an embedded display backplane or processor-to-display module that needs a 21-bit parallel input converted into a compact differential Channel Link connection. The interface reduces the number of conductors needed for a wide bus and provides a forwarded data-strobe relationship for source-synchronous timing. Its 48-pin TSSOP package supports conventional surface-mount assembly, while the +3.3 V operating point integrates with common display-controller logic. Practical implementation should preserve differential pair symmetry, provide a continuous ground reference, and keep the clock pair matched in length to the data pairs. Display refresh timing must also be checked against the receiver's specified edge and propagation-delay limits.
Được đề xuất
Embedded Control and Data Acquisition
The DS90CR216MTD-TI can consolidate a 21-bit parallel sensor, actuator, or digital-control group into a differential data-and-strobe link between embedded modules. The 66 MHz maximum clock provides headroom for repeated acquisition or command cycles, while differential transmission improves noise immunity over longer inter-module wiring. The receiver is particularly relevant where direct point-to-point routing of 21 single-ended signals would consume excessive pins or cable conductors. The source logic must maintain the required setup and hold relationship to the rising-edge strobe, and the receiver site needs local decoupling. Timing closure must include the transmitter delay, cable delay, connector delay, and receiver propagation delay across voltage and temperature extremes.
Được đề xuất
Secure Monitoring and Camera Modules
The DS90CR216MTD-TI can carry grouped timing, control, and status data in a camera or monitoring module where a conventional parallel bus would be too wide or noisy. Twenty-one data bits per clocked transfer provide useful payload density, and the differential Channel Link outputs support a compact shielded or twisted-pair connection. Differential signaling is advantageous in equipment containing motors, switching regulators, or long ground paths because it suppresses common-mode disturbances that can corrupt single-ended interfaces. The link still requires careful design: maintain controlled differential impedance, avoid discontinuities in return paths, observe the receiver's input termination requirements, and validate operation with the actual cable length. Security-sensitive equipment should also confirm that separate data paths meet its isolation and compliance requirements.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho DS90CR216MTD-TI — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | DS90CR216MTD | DS90CR216MTD/NOPB | DS90CR216MTDX/NOPB | DS90CR216AMTD/NOPB | DS90CR216AMTDX/NOPB |
|---|---|---|---|---|---|---|
| Package | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP | 48-TSSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Supply Voltage | +3.3 V | +3.3 V | +3.3 V | +3.3 V | +3.3 V | +3.3 V |
| Maximum Clock Frequency | 66 MHz | 66 MHz | 66 MHz | 66 MHz | 66 MHz | 66 MHz |
| Data Width | 21 bits | 21 bits | 21 bits | 21 bits | 21 bits | 21 bits |
| Number of Outputs | 21 outputs | 21 outputs | 21 outputs | 21 outputs | 21 outputs | 21 outputs |
| Data Strobe | Rising edge | Rising edge | Rising edge | Rising edge | Rising edge | Rising edge |
| Interface Type | LVDS Channel Link receiver | LVDS Channel Link receiver | LVDS Channel Link receiver | LVDS Channel Link receiver | LVDS Channel Link receiver | LVDS Channel Link receiver |
Bảo phân biệt quan trọng
- Full 21-bit Channel Link width in the same package family (vsDS90CR215MTD)
- Direct manufacturer-family replacement path (vsDS90CR216MTD/NOPB)
- No PCB modification for verified same-package orderings (vsDS90CR216AMTDX/NOPB)
Ghi chú thiết kế
Treat each differential data or clock pair as a controlled-impedance transmission line rather than as two unrelated traces. Match pair geometry, minimize stubs, maintain continuous reference planes, and use the receiver input termination shown in the manufacturer application diagram. Account for connector and cable delay when validating the rising-edge data-strobe relationship; nominal 66 MHz operation alone does not guarantee adequate timing margin on every interconnect.
Place the receiver close to the connector or cable entry point when practical, then route the differential pairs over a continuous ground plane without plane splits. Keep switching regulators, high-speed clocks, and other noisy return currents away from the input region. Match the clock pair to the data-group timing budget and avoid adding test pads or long branches that create impedance discontinuities near the 48-pin TSSOP.
Do not substitute a DS90CR215 ordering, a different package, or an unrelated LVDS serializer based only on clock frequency. Confirm the 21-bit width, rising-edge behavior, terminal assignments, supply voltage, package drawing, propagation delay, and temperature grade. Also verify whether the required assembly form uses the M, AM, or X ordering suffix; these suffixes can change reel orientation or other orderable attributes without changing the core receiver function.
Follow the manufacturer power-connection and decoupling diagram when assigning ground and supply pins in the exposed-pad-style TSSOP footprint. Keep the +3.3 V return path short and provide local bypass capacitance at the device according to the recommended circuit. Confirm that both the receiver and its link partner tolerate supply noise and voltage tolerance at the connector, since link integrity can degrade if the remote transmitter introduces overshoot beyond the receiver's operating conditions.
Thông tin tuân thủ
The manufacturer ordering information includes NOPB variants, but no explicit RoHS, REACH, AEC-Q100, halogen-free, or conflict-minerals statement was identified in the verified listings. The target DS90CR216MTD-TI suffix-specific compliance status remains unknown.