EP1M350F780I8 - Mercury FPGA 350K Gates | Intel / Altera
MPN: EP1M350F780I8 ✗ Cuối đờiEP1M350F780I8 Tóm tắt
A Programmable Logic Device (PLD) is an integrated circuit that can be configured by the end user to implement custom digital logic. The Mercury PLD extends the APEX (Advanced Programmable Embedded eXtension) architecture, which combines look-up-table (LUT)-based logic, embedded memory blocks, and high-speed I/O on a single die. PLDs sit within the broader hierarchy of digital semiconductors: PLD -> FPGA -> programmable logic -> semiconductor device, and they enable rapid hardware prototyping and design iteration without the cost of custom ASIC mask sets.
Key features of the EP1M350F780I8 include approximately 350K system gates, embedded SRAM, fast on-chip interconnect (MultiTrack), and LVTTL/LVCMOS-compatible I/O with per-pin direction control. The device supports in-system programmability through the IEEE 1149.1 JTAG interface and is built on a 0.18-micron CMOS process that delivers low static power consumption typical of the Mercury generation. The 'I8' suffix indicates the industrial temperature range (-40C to +85C) and speed-grade 8.
Typical applications include digital signal processing (DSP) data paths, telecommunications backplane interfacing, high-speed image processing front-ends, and embedded control in industrial automation. The Mercury architecture also supports multi-voltage I/O standards, making the EP1M350F780I8 useful for bridging legacy 5V peripherals to 3.3V or 2.5V processor buses.
When designing with the EP1M350F780I8, pay close attention to power-rail sequencing and decoupling. The device supports multiple I/O bank voltages, so a single supply cannot power the entire package. Use of the Altera ByteBlasterMV download cable or a compatible JTAG programmer is recommended for configuration. Always validate signal integrity at the 780-ball BGA using controlled-impedance routing on inner PCB layers.
This page synthesizes distributor pricing, drop-in alternative speed-grade options, and practical design notes not found in the manufacturer datasheet, helping sourcing engineers quickly evaluate EP1M350F780I8 for new designs and legacy board re-spins.
Bộ thay thế dễ dàng lắp đặt cho EP1M350F780I8 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EP1M350F780I8 (cùng hình factor và footprint) — khác nhau ở Operating Temperature, Speed Grade, Package, Family, Process Technology.
EP1M350F780I7N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780C8
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780C7N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780C7
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780I7
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780C6
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP1M350F780I8 Tỷ lệ tối đa & tính chất điện
| Family | Altera Mercury (APEX PLD family) |
| System Gates | Approx. 350,000 |
| Hộp | 780-ball FineLine BGA (F780) |
| Nhiệt độ hoạt động | -40C to +85C (Industrial) |
| Temperature Grade | Industrial ('I' suffix) |
| Speed Grade | 8 |
| Process Technology | 0.18 micron CMOS |
| Supply Voltage - I/O | Multi-voltage I/O banks supported |
| I/O Standard Support | LVTTL, LVCMOS, PCI (per datasheet) |
| Configuration Interface | IEEE 1149.1 JTAG |
| Kiểu lắp đặt | Surface Mount (BGA) |
Hướng dẫn cấu hình chân EP1M350F780I8 780-ball fineline bga (f780)
Cấu hình chân cho EP1M350F780I8 (780-ball fineline bga (f780) gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho EP1M350F780I8.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
EP1M350F780I8 phù hợp cho 6 Áp dụngs: Telecommunications Backplane Interface, Digital Signal Processing (DSP) Front-End, Industrial Automation Controllers, Legacy System Repair and Maintenance, High-Speed Image Processing Pipeline, Avionics and Military Embedded Computing.
Telecommunications Backplane Interface
The EP1M350F780I8 fits telecom backplane bridging applications thanks to its 350K system gates and multi-voltage I/O bank support. With LVTTL/LVCMOS compatibility, the device can interface legacy 5V bus segments to modern 3.3V or 2.5V PHYs without external level shifters, reducing BOM cost and board area. Industrial temperature rating (-40C to +85C) makes it suitable for central-office environments. Pin-to-pin compatibility across the Mercury F780 family allows easy migration to faster speed grades (I7, I6) if timing closure becomes difficult.
Được đề xuất
Digital Signal Processing (DSP) Front-End
For DSP front-end glue logic, the EP1M350F780I8 provides ample logic capacity to implement FIFO buffers, address generation, and protocol conversion alongside a dedicated DSP processor. The 350K gate count accommodates parallel filter architectures and sample-rate conversion stages. The industrial temperature grade supports outdoor or industrial-cabinet deployments. Designers should use the embedded SRAM blocks efficiently for coefficient storage, freeing logic resources for arithmetic paths.
Được đề xuất
Industrial Automation Controllers
In PLC and motion-control platforms, the EP1M350F780I8 can host custom control algorithms, encoder interfaces, and fieldbus glue logic in a single device. Its 780-ball FineLine BGA package supports high I/O count required for multi-axis servo control. Industrial temperature grade ensures operation in factory-floor enclosures. Designers should isolate motor-drive grounds from the PLD's sensitive I/O banks to prevent noise injection into JTAG and configuration logic.
Được đề xuất
Legacy System Repair and Maintenance
The EP1M350F780I8 is primarily targeted at repair and maintenance of legacy systems built around the Mercury PLD family. Sourcing is constrained due to obsolete status, so board-level repair often requires either re-spinning the Mercury section with a Stratix/Cyclone equivalent or sourcing original parts from authorized distributors holding residual stock. Engineers should qualify a second source early and consider re-spin to active lifecycle parts for ongoing production.
Được đề xuất
High-Speed Image Processing Pipeline
Image-acquisition boards using the EP1M350F780I8 can implement line buffers, pixel-format conversion, and timing generators in programmable logic. The 350K gates comfortably accommodate 8-bit and 16-bit wide video paths. Multi-voltage I/O banks allow direct connection to CMOS image sensors operating at 2.5V or 3.3V. The industrial temperature range supports outdoor machine-vision installations such as traffic monitoring and security cameras.
Được đề xuất
Avionics and Military Embedded Computing
Although not radiation-hardened, the EP1M350F780I8 industrial temperature range and robust 780-ball BGA package suit certain ruggedized military and avionics subsystems where commercial-grade parts are acceptable. Designers in this segment should validate against vibration, shock, and thermal cycling per MIL-STD-810. The Mercury family is mature and well-documented, which simplifies DO-254-style design assurance. For new programs, modern Stratix or Cyclone FPGAs with active lifecycle support are recommended.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EP1M350F780I8 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EP1M350F780I7N | EP1M350F780C8 | EP1M350F780C7N | EP1M350F780C7 | EP1M350F780I7 | EP1M350F780C6 |
|---|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | 780-ball FineLine BGA (F780) | 780-ball FineLine BGA (F780) - same | 780-ball FineLine BGA (F780) - same | 780-ball FineLine BGA (F780) - same | 780-ball FineLine BGA (F780) - same | 780-ball FineLine BGA (F780) - same | 780-ball FineLine BGA (F780) - same |
| System Gates | 350K | 350K | 350K | 350K | 350K | 350K | 350K |
| Speed Grade | 8 | 7 (faster) | 8 | 7 (faster) | 7 (faster) | 7 (faster) | 6 (fastest) |
| Temperature Grade | Industrial -40C to +85C | Industrial -40C to +85C | Commercial 0C to +70C | Commercial 0C to +70C | Commercial 0C to +70C | Industrial -40C to +85C | Commercial 0C to +70C |
| Family | Mercury PLD | Mercury PLD | Mercury PLD | Mercury PLD | Mercury PLD | Mercury PLD | Mercury PLD |
| Configuration Interface | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 | JTAG IEEE 1149.1 |
| Process Technology | 0.18 micron CMOS | 0.18 micron CMOS | 0.18 micron CMOS | 0.18 micron CMOS | 0.18 micron CMOS | 0.18 micron CMOS | 0.18 micron CMOS |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Bảo phân biệt quan trọng
- Industrial temperature rating for harsh environments (vsEP1M350F780C8)
- Speed grade 8 for cost-sensitive timing closure (vsEP1M350F780I7N)
- FineLine BGA package for high I/O density (vsEP1M350F672C7)
Ghi chú thiết kế
The EP1M350F780I8 supports multi-voltage I/O banks; design separate decoupling networks for each bank voltage (typically 2.5V, 3.3V, and 5V). Use 0.1uF X7R ceramic capacitors placed as close as possible to each bank power pin, with bulk tantalum or polymer capacitors on the supply side. Power-rail sequencing should bring up core voltage VCCINT before I/O voltages to avoid latch-up. Refer to the Altera Mercury family datasheet for recommended decoupling topologies and supply-current budgets per bank.
The 780-ball FineLine BGA requires controlled-impedance PCB routing on inner layers. Use a 4-layer or 6-layer stack-up with continuous ground planes beneath the BGA to control return-path inductance. Escape routing should use vias-in-pad (VIP) or dogbone fan-out patterns; microvia technology is recommended for sub-1mm pitch. After reflow, perform X-ray inspection on every joint to verify solder wetting and detect head-in-pillow defects.
Obsolete Mercury parts have dwindling software support in modern Intel Quartus Prime releases. Confirm that your Quartus II version (legacy) supports the EP1M350F780I8 device library before committing to a design. Also verify that the JTAG programmer (ByteBlasterMV or USB-Blaster) is available for configuration download. Migrate to Stratix or Cyclone for new designs where possible to retain software tool support.
At high toggle rates, the EP1M350F780I8 generates simultaneous switching noise (SSN) that can couple into adjacent I/O banks. Stagger clock edges across banks, enable slew-rate control where available, and add series termination resistors near driver outputs for high-speed signals (>100 MHz). Use the IBIS model from Altera to perform pre-layout signal-integrity simulation.
Thông tin tuân thủ
Compliance data not available in verified web sources for EP1M350F780I8. Industrial temperature grade implied by 'I' suffix per Altera naming convention. AEC-Q100 not applicable - FPGAs are not automotive-qualified components in this family.