EP910LI-30T - 24-Macrocell Classic EPLD, 30ns, PQCC-44 | Altera
MPN: EP910LI-30T ✗ Cuối đờiEP910LI-30T Tóm tắt
What is a Classic EPLD? A Classic Erasable Programmable Logic Device (EPLD) is a type of programmable logic IC that combines AND/OR arrays with user-programmable macrocells, enabling the replacement of multiple discrete SSI/MSI logic gates with a single re-programmable device. EPLDs sit at the lower end of the programmable logic hierarchy below CPLDs and FPGAs, offering non-volatile (UV-erasable) configuration, predictable timing, and fast pin-to-pin propagation delays - ideal for glue-logic, state-machine, and bus-Interface applications.
The EP910LI-30T delivers 24 macrocells, 10 dedicated input pins, 24 I/O pins (bidirectional), and operates over the industrial temperature range of -40°C to +85°C. It is fabricated on advanced CMOS technology, providing high-speed, low-power logic integration with tPD of 30 ns, tCO of 20 ns, and fMAX compatible with high-speed control logic. The device is housed in a J-leaded PQCC-44 surface-mount package.
Architecturally, the EP910 uses a sum-of-products PLA structure feeding registered output macrocells, with each macrocell offering product-term allocation, output polarity control, and a flip-flop. Programming is performed via a standard EPROM programmer using the Altera Logic Programmer or compatible tools.
Typical applications include bus-interface glue logic, state-machine replacement of discrete 74LS/74HC logic, address decoding in microprocessor systems, and timing-control circuits in industrial controllers. Designers often choose the EP910 family when non-volatile configuration, deterministic timing, and high I/O count in a small plastic package are required.
When designing with this device, note that the PQCC-44 footprint requires socketed or reflow assembly; ensure proper handling of UV-erasable windowed versions if reprogramming is needed. For modern designs, verify that software tools (Altera MAX+PLUS II legacy support) are still accessible in your workflow.
This page synthesizes distributor pricing, drop-in alternatives, and practical design notes not found in the original Altera datasheet.
Bộ thay thế dễ dàng lắp đặt cho EP910LI-30T — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EP910LI-30T (cùng hình factor và footprint) — khác nhau ở Supply Voltage (VCC), Package, Propagation Delay (tPD), Family, Mounting Type.
EP910LI-30
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EP910LC-30T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP910LC44-30T
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP910LC-30
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EP910LI-20T
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →EP910LI-30T Tỷ lệ tối đa & tính chất điện
| Family | Altera Classic EPLD |
| Number of Macrocells | 24 |
| Usable Gates | 450 |
| Propagation Delay (tPD) | 30 ns |
| Dedicated Inputs | 10 |
| I/O Pins | 24 |
| Hộp | PQCC-44 (J-lead) |
| Nhiệt độ hoạt động | -40C to +85C (Industrial) |
| Technology | CMOS, UV-erasable |
| Kiểu lắp đặt | Surface Mount |
| Programming Method | EPROM (UV-erasable) via Altera Logic Programmer |
Cấu hình chân EP910LI-30T
| Chân 1 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 2 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 3 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 4 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 5 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 6 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 7 | GND — Ground |
| Chân 8 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 9 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 10 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 11 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 12 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 13 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 14 | INPUT — Dedicated input pin |
| Chân 15 | INPUT — Dedicated input pin |
| Chân 16 | INPUT — Dedicated input pin |
| Chân 17 | INPUT — Dedicated input pin |
| Chân 18 | INPUT — Dedicated input pin |
| Chân 19 | GND — Ground |
| Chân 20 | INPUT — Dedicated input pin |
| Chân 21 | INPUT — Dedicated input pin |
| Chân 22 | INPUT — Dedicated input pin |
| Chân 23 | INPUT — Dedicated input pin |
| Chân 24 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 25 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 26 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 27 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 28 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 29 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 30 | GND — Ground |
| Chân 31 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 32 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 33 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 34 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 35 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 36 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 37 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 38 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 39 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 40 | I/O — Macrocell I/O pin (bidirectional) |
| Chân 41 | INPUT/CLK — Dedicated input / Global clock |
| Chân 42 | INPUT/CLR — Dedicated input / Global clear |
| Chân 43 | VCC — Supply voltage |
| Chân 44 | VCC — Supply voltage |
Ứng dụng tiêu biểu
EP910LI-30T phù hợp cho 6 Áp dụngs: Microprocessor Bus Interface Glue Logic, State Machine Replacement for 74LS/74HC Logic, Address Decoding in Microprocessor Systems, Industrial Control Timing Circuits, Legacy Peripheral Replacement Logic, Prototyping Platform for Glue Logic.
Microprocessor Bus Interface Glue Logic
The EP910LI-30T is well-suited to microprocessor bus-interface glue logic, where its 24 macrocells and 30 ns tPD can replace multiple 74LS245/74LS244 buffers and address-decoder packages. With 10 dedicated inputs and 24 bidirectional I/O pins, the device can decode address lines, generate chip-selects for memory and peripherals, and implement bus-control state machines in a single PQCC-44 package. The industrial -40°C to +85°C temperature range makes the part appropriate for embedded SBCs and industrial controllers. Designers typically pair the EP910LI-30T with a 16- or 32-bit microcontroller to consolidate 5-10 discrete logic packages into one programmable device, reducing PCB area and BOM cost.
Được đề xuất
State Machine Replacement for 74LS/74HC Logic
The EP910LI-30T can replace 4-8 packages of 74LS/74HC flip-flops, decoders, and multiplexers when implementing small to medium state machines. Each macrocell provides a D flip-flop with product-term clocking and clear, allowing sequential logic to be expressed directly in the AND/OR array. The 30 ns tPD supports state-machine clock rates up to ~10 MHz, sufficient for most industrial-control, instrumentation, and serial-protocol sequencing tasks. The non-volatile UV-erasable configuration means the state machine starts running at power-on without an external boot device - a key advantage over SRAM-based FPGAs in safety-critical or deterministic applications.
Được đề xuất
Address Decoding in Microprocessor Systems
Address decoding for memory and peripheral chip-select signals is a classic application for the EP910LI-30T, leveraging its 10 dedicated inputs to monitor address and control lines (A0-A7 plus RD/WR). The 24 I/O pins can drive up to 24 chip-select outputs, replacing an entire 74LS138/74LS139 decoder tree in one package. With 30 ns tPD, the part adds negligible address-to-chip-select delay, allowing it to sit between the CPU and memory without impacting access-time budgets. Designers can reprogram the decoder map via UV erasure when memory layouts change, providing hardware reuse across product variants without board respins.
Được đề xuất
Industrial Control Timing Circuits
The EP910LI-30T's industrial -40°C to +85°C temperature range and 30 ns deterministic timing make it appropriate for industrial-control timing circuits such as conveyor sequencers, valve controllers, and machine-tool interfaces. The 24 macrocells can encode timer chains, watchdog logic, and interlock sequences without external counters or one-shots. The PQCC-44 J-lead package withstands industrial vibration and thermal cycling better than ceramic-windowed DIPs. Engineers use the EP910LI-30T in PLCs and stand-alone controllers where non-volatile configuration and predictable timing are required, and where modern CPLD software tools are not available in legacy workflows.
Được đề xuất
Legacy Peripheral Replacement Logic
When modernizing equipment that uses now-discrete 74LS logic boards, the EP910LI-30T can consolidate 5-15 logic packages into a single PQCC-44 EPLD, reducing board size and improving reliability through fewer solder joints. The 450 usable gates cover typical peripheral tasks like serial-port encoding (UART bit-banging), parallel-port handshaking, and interrupt-controller glue. Because the device is non-volatile, it boots instantly at power-on - critical for legacy military, aerospace, and medical equipment where deterministic startup behavior is mandated. Rochester Electronics supplies traceable date-coded units for these long-lifecycle applications.
Được đề xuất
Prototyping Platform for Glue Logic
Engineering labs and university courses use the EP910LI-30T as a UV-erasable prototyping platform for teaching programmable logic concepts and for rapid iteration of glue-logic designs. Designers can compile a design, program the device with an Altera Logic Programmer, and verify operation in-circuit - then UV-erase and reprogram in minutes. The 30 ns tPD and 24 macrocells are sufficient for educational examples like ALU glue, simple CPU decode, and I/O expansion. The PQCC-44 package fits standard 44-pin PLCC sockets, making the part easy to swap between prototypes.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EP910LI-30T — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EP910LI-30 | EP910LC-30T | EP910LC44-30T | EP910LC-30 | EP910LI-20T |
|---|---|---|---|---|---|---|
| Brand | Altera | Altera | Altera | Altera | Altera | Altera |
| Package | PQCC-44 | PQCC-44 - same | PQCC-44 - same | PQCC-44 - same | PQCC-44 - same | PQCC-44 - same |
| Macrocells | 24 | 24 | 24 | 24 | 24 | 24 |
| Usable Gates | 450 | 450 | 450 | 450 | 450 | 450 |
| Propagation Delay (tPD) | 30 ns | 30 ns | 30 ns | 30 ns | 30 ns | 20 ns (-33%) |
| Temperature Range | -40C to +85C (Industrial) | -40C to +85C (Industrial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | 0C to +70C (Commercial) | -40C to +85C (Industrial) |
| Packaging | Tape & Reel | Tray | Tape & Reel | Tape & Reel | Tray | Tape & Reel |
| Lifecycle Status | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete | Obsolete |
Bảo phân biệt quan trọng
- Industrial temperature range option (vsEP910LC-30T)
- Tape and Reel packaging for SMT (vsEP910LI-30)
- Balanced speed/cost in 30ns tier (vsEP910LI-20T)
Ghi chú thiết kế
The EP910LI-30T PQCC-44 J-lead package requires careful PCB land-pattern design per JEDEC MO-047. Recommended pad dimensions are 0.040 x 0.085 inch with 0.050 inch pitch. Use a socket (e.g., 44-pin PLCC socket, 3M 8444-21B1-RK or equivalent) for prototyping to allow UV-erase and reprogram cycles; for production, reflow solder with no-clean flux. Ensure adequate thermal relief on VCC/GND planes because the J-leads provide limited thermal conduction. Place decoupling capacitors (0.1 uF ceramic per VCC pin) within 100 mils of the package leads.
The Altera Classic EPLD family is UV-erasable; windowed ceramic DIP variants (e.g., EP910LC-12 ceramic) are required if you need to reprogram after solder assembly. Once a plastic PQCC-44 part like the EP910LI-30T is soldered, it cannot be erased - it is one-time-programmable (OTP) in plastic. Ensure your design is fully verified in a windowed programmer or socketed prototype before committing the plastic part to production. Additionally, MAX+PLUS II software is end-of-life - plan for legacy Windows XP/7 virtual-machine support in your design flow.
When using the EP910LI-30T as a bus decoder or glue-logic device on high-speed microprocessor buses (>25 MHz), observe 30 ns tPD through the device. The macrocell output drive is limited (typically 24 mA IOL per the family datasheet); add external bus drivers (74LS245/74LVC245) if driving heavily-loaded backplanes or long traces. Use the dedicated clock/clear pins (pins 41/42 per the PQCC-44 pinout) rather than routed clocks for predictable timing. Keep I/O traces short and use ground-pour shielding to minimize crosstalk in dense designs.
Thông tin tuân thủ
RoHS, REACH, and lead-free status not explicitly confirmed in the provided data. Rochester Electronics offers both RoHS-compliant and legacy SnPb finishes depending on date code. AEC-Q100 not applicable - this is a logic device, not an automotive-qualified IC.
