EPM7160STC100-10 - MAX 7000S CPLD, 160 Macrocells, 100-pin TQFP | Intel
MPN: EPM7160STC100-10 ⚠ Lần mua cuốiEPM7160STC100-10 Tóm tắt
A CPLD (Complex Programmable Logic Device) is a non-volatile programmable logic device that combines multiple PAL/GAL-like macrocell arrays on a single chip with a programmable interconnect matrix. In the system hierarchy, a CPLD sits between simple SPLDs (PALs/GALs) and larger FPGAs, offering deterministic timing, instant-on behavior from non-volatile EEPROM, and typically lower I/O counts than FPGAs but higher logic density than 22V10-style GALs. The MAX 7000S family is Altera's second-generation MAX architecture, characterized by fast 5-10 ns propagation delays and pin-compatible upgrades within the family.
Key features of the EPM7160STC100-10 include 160 macrocells organized in logic array blocks (LABs), 84 user I/Os, 3.2K usable gates, a 100 MHz internal counter frequency, and 5.0 V VCC operation. The -10 speed grade denotes a 10 ns maximum pin-to-pin delay (tPD1) and a 6 ns global clock setup time, suitable for glue-logic, bus-interface, and state-machine applications where deterministic timing is critical. The device also offers programmable power savings with 50% or 100% toggle-rate reduction modes, multi-voltage I/O support, and JTAG boundary-scan test compliance.
Architecturally, the EPM7160STC100-10 uses an EEPROM cell to store the configuration, which means the device powers up instantly in a known state without external boot memory. Each macrocell contains a programmable AND/OR array, a product-term allocator, a flip-flop, and an I/O control block, providing both combinational and registered logic with flexible feedback paths. The interconnect uses Altera's FastTrack continuous interconnect matrix, minimizing routing delay variations across the chip.
Typical applications include bus-interface bridging (e.g., 8-bit/16-bit MCU to 32-bit peripheral glue-logic), address decoding and chip-select generation in microprocessor systems, state-machine control for industrial automation, peripheral interface adaptation (UART, SPI, I2C, parallel buses), and legacy TTL/CMOS logic integration on a single programmable device. The instant-on EEPROM configuration also suits safety-critical and automotive underhood applications requiring deterministic power-up behavior.
Designers should note that the EPM7160STC100-10 belongs to a mature, multi-decade product family; some speed grades and temperature grades have been migrated to the -10N suffix variant. For new designs, evaluate MAX II or MAX V CPLDs as modern equivalents, but for pin-compatible drop-in replacement on existing PCBs the EPM7160STC100-10N, EPM7160STC100-7, and EPM7160STC100-15 offer parametric-equivalent second sources within the same 100-pin TQFP footprint.
This page synthesizes distributor pricing, JTAG/ISP programming parameters, and same-family drop-in alternatives not found in a single distributor listing, with values anchored to the manufacturer datasheet and DigiKey/Mouser inventory data as of 2026-09-13.
Bộ thay thế dễ dàng lắp đặt cho EPM7160STC100-10 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với EPM7160STC100-10 (cùng hình factor và footprint) — khác nhau ở Package, Operating Temperature, Propagation Delay (tPD), PCI Compliance, Programmable Type.
EPM7160STC100-10N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM7160STC100-7
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160STC100-15
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160STC100-6
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
EPM7160STI100-10
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM7160STC100-10F
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →EPM7160STC100-10 Tỷ lệ tối đa & tính chất điện
| Family | MAX 7000S |
| Device Type | CPLD (Complex Programmable Logic Device) |
| Macro Cells | 160 |
| User I/Os | 84 |
| Usable Gates | 3,200 |
| Logic Elements | 160 macrocells / 10 Logic Array Blocks |
| Supply Voltage (VCC) | 5.0 V (4.75 V - 5.25 V) |
| Propagation Delay (tPD1) | 10 ns |
| Global Clock Setup Time | 6 ns |
| Internal Counter Frequency | 100 MHz |
| Technology | CMOS, EEPROM-based |
| In-System Programmability | Yes (IEEE 1149.1 JTAG) |
| Hộp | 100-pin TQFP |
| Nhiệt độ hoạt động | 0 C to +70 C (commercial) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Non-RoHS (legacy Altera part; -10N variant is RoHS) |
Cấu hình chân EPM7160STC100-10
| Chân 1 | I/O — User I/O pin (bank 1) |
| Chân 2 | I/O — User I/O pin (bank 1) |
| Chân 3 | I/O — User I/O pin (bank 1) |
| Chân 4 | I/O — User I/O pin (bank 1) |
| Chân 5 | I/O — User I/O pin (bank 1) |
| Chân 6 | I/O — User I/O pin (bank 1) |
| Chân 7 | I/O — User I/O pin (bank 1) |
| Chân 8 | I/O — User I/O pin (bank 1) |
| Chân 9 | I/O — User I/O pin (bank 1) |
| Chân 10 | I/O — User I/O pin (bank 1) |
| Chân 11 | I/O — User I/O pin (bank 1) |
| Chân 12 | TDI — JTAG Test Data In |
| Chân 13 | TMS — JTAG Test Mode Select |
| Chân 14 | TCK — JTAG Test Clock |
| Chân 15 | I/O — User I/O pin (bank 1) |
| Chân 16 | I/O — User I/O pin (bank 1) |
| Chân 17 | I/O — User I/O pin (bank 1) |
| Chân 18 | I/O — User I/O pin (bank 1) |
| Chân 19 | I/O — User I/O pin (bank 1) |
| Chân 20 | I/O — User I/O pin (bank 1) |
| Chân 21 | VCC — 5.0 V supply (bank 1) |
| Chân 22 | I/O — User I/O pin (bank 1) |
| Chân 23 | I/O — User I/O pin (bank 1) |
| Chân 24 | GCLK1 — Global clock input 1 |
| Chân 25 | OE1 — Global output enable 1 |
| Chân 26 | GCLRn — Global clear (active low) |
| Chân 27 | I/O — User I/O pin (bank 2) |
| Chân 28 | I/O — User I/O pin (bank 2) |
| Chân 29 | I/O — User I/O pin (bank 2) |
| Chân 30 | I/O — User I/O pin (bank 2) |
| Chân 31 | I/O — User I/O pin (bank 2) |
| Chân 32 | I/O — User I/O pin (bank 2) |
| Chân 33 | I/O — User I/O pin (bank 2) |
| Chân 34 | I/O — User I/O pin (bank 2) |
| Chân 35 | I/O — User I/O pin (bank 2) |
| Chân 36 | GND — Ground |
| Chân 37 | I/O — User I/O pin (bank 2) |
| Chân 38 | I/O — User I/O pin (bank 2) |
| Chân 39 | I/O — User I/O pin (bank 2) |
| Chân 40 | I/O — User I/O pin (bank 2) |
| Chân 41 | I/O — User I/O pin (bank 2) |
| Chân 42 | I/O — User I/O pin (bank 2) |
| Chân 43 | I/O — User I/O pin (bank 2) |
| Chân 44 | I/O — User I/O pin (bank 2) |
| Chân 45 | I/O — User I/O pin (bank 2) |
| Chân 46 | VCC — 5.0 V supply (bank 2) |
| Chân 47 | I/O — User I/O pin (bank 2) |
| Chân 48 | I/O — User I/O pin (bank 2) |
| Chân 49 | GCLK2 — Global clock input 2 |
| Chân 50 | OE2 — Global output enable 2 |
| Chân 51 | I/O — User I/O pin (bank 3) |
| Chân 52 | I/O — User I/O pin (bank 3) |
| Chân 53 | I/O — User I/O pin (bank 3) |
| Chân 54 | I/O — User I/O pin (bank 3) |
| Chân 55 | I/O — User I/O pin (bank 3) |
| Chân 56 | I/O — User I/O pin (bank 3) |
| Chân 57 | I/O — User I/O pin (bank 3) |
| Chân 58 | I/O — User I/O pin (bank 3) |
| Chân 59 | I/O — User I/O pin (bank 3) |
| Chân 60 | GND — Ground |
| Chân 61 | I/O — User I/O pin (bank 3) |
| Chân 62 | I/O — User I/O pin (bank 3) |
| Chân 63 | I/O — User I/O pin (bank 3) |
| Chân 64 | I/O — User I/O pin (bank 3) |
| Chân 65 | I/O — User I/O pin (bank 3) |
| Chân 66 | I/O — User I/O pin (bank 3) |
| Chân 67 | I/O — User I/O pin (bank 3) |
| Chân 68 | I/O — User I/O pin (bank 3) |
| Chân 69 | I/O — User I/O pin (bank 3) |
| Chân 70 | I/O — User I/O pin (bank 3) |
| Chân 71 | VCC — 5.0 V supply (bank 3) |
| Chân 72 | I/O — User I/O pin (bank 4) |
| Chân 73 | I/O — User I/O pin (bank 4) |
| Chân 74 | I/O — User I/O pin (bank 4) |
| Chân 75 | I/O — User I/O pin (bank 4) |
| Chân 76 | I/O — User I/O pin (bank 4) |
| Chân 77 | I/O — User I/O pin (bank 4) |
| Chân 78 | I/O — User I/O pin (bank 4) |
| Chân 79 | I/O — User I/O pin (bank 4) |
| Chân 80 | I/O — User I/O pin (bank 4) |
| Chân 81 | I/O — User I/O pin (bank 4) |
| Chân 82 | I/O — User I/O pin (bank 4) |
| Chân 83 | GND — Ground |
| Chân 84 | I/O — User I/O pin (bank 4) |
| Chân 85 | I/O — User I/O pin (bank 4) |
| Chân 86 | I/O — User I/O pin (bank 4) |
| Chân 87 | I/O — User I/O pin (bank 4) |
| Chân 88 | I/O — User I/O pin (bank 4) |
| Chân 89 | I/O — User I/O pin (bank 4) |
| Chân 90 | I/O — User I/O pin (bank 4) |
| Chân 91 | I/O — User I/O pin (bank 4) |
| Chân 92 | I/O — User I/O pin (bank 4) |
| Chân 93 | I/O — User I/O pin (bank 4) |
| Chân 94 | I/O — User I/O pin (bank 4) |
| Chân 95 | VCC — 5.0 V supply (bank 4) |
| Chân 96 | I/O — User I/O pin (bank 4) |
| Chân 97 | I/O — User I/O pin (bank 4) |
| Chân 98 | I/O — User I/O pin (bank 4) |
| Chân 99 | TDO — JTAG Test Data Out |
| Chân 100 | I/O — User I/O pin (bank 1) |
Ứng dụng tiêu biểu
EPM7160STC100-10 phù hợp cho 6 Áp dụngs: Microprocessor Bus Glue Logic, Address Decoding & Chip-Select Generation, Industrial Control State Machines, Peripheral Interface Bridging (UART/SPI/I2C), Legacy TTL/CMOS Logic Integration, Test Equipment & JTAG Boundary-Scan Control.
Microprocessor Bus Glue Logic
The EPM7160STC100-10 is widely used as a glue-logic bridge between microprocessors and peripherals where deterministic 10 ns timing matters more than raw logic density. Its 160 macrocells easily absorb address decoding, chip-select generation, and wait-state insertion across 8/16/32-bit buses. The 5.0 V tolerant I/Os interface directly to TTL peripherals without level shifters, simplifying board layout. Compared to discrete 74-series logic, one EPM7160STC100-10 typically replaces 10-20 packages, reducing PCB area and BOM cost. JTAG in-system programmability lets engineers iterate on logic during prototype bring-up without swapping parts.
Được đề xuất
Address Decoding & Chip-Select Generation
With 160 macrocells and 84 user I/Os, the EPM7160STC100-10 can decode large memory maps and generate chip-select signals for banks of memory-mapped peripherals simultaneously. Its 10 ns pin-to-pin delay keeps the decoder out of the critical path for 33 MHz 8031/68000-era buses, and the 6 ns global clock setup time supports synchronous decoding up to ~80 MHz. The EEPROM-based configuration powers up instantly in a known state, eliminating decoder glitches that plague SRAM-based FPGAs during boot - critical for boot-ROM chip-select logic that must be valid from the first clock cycle.
Được đề xuất
Industrial Control State Machines
The deterministic timing and instant-on EEPROM configuration of the EPM7160STC100-10 make it ideal for industrial PLC state machines controlling stepper motors, solenoids, and conveyor sequencing. Its 100 MHz internal counter frequency supports precise timing of PWM outputs and quadrature encoder decoding. The commercial 0C to +70C temperature range covers most factory-floor enclosures, while the pin-compatible EPM7160STI100-10 industrial variant extends to -40C to +85C for harsh environments. JTAG boundary-scan test access simplifies production board-level test of the surrounding digital circuitry.
Được đề xuất
Peripheral Interface Bridging (UART/SPI/I2C)
The EPM7160STC100-10 frequently bridges between incompatible peripheral interfaces - translating between SPI and parallel buses, multiplexing UARTs, or converting I2C to memory-mapped registers. Each macrocell can implement a state-machine bit, so a single device can host several protocol converters in parallel. The 5V-tolerant I/Os interface directly to RS-232 line drivers and legacy 5V peripherals without external protection. Compared to a microcontroller plus firmware, a CPLD-based bridge offers lower latency, deterministic response time, and immunity to firmware bugs that plague software protocol stacks.
Được đề xuất
Legacy TTL/CMOS Logic Integration
The EPM7160STC100-10 is a drop-in consolidation device for legacy boards built from discrete 74LS, 74HC, and 74F logic gates, latches, and counters. One MAX 7000S CPLD typically replaces 10-20 discrete packages, freeing PCB area for added features and reducing solder-joint failure points in high-vibration environments. The EEPROM configuration is fully non-volatile, so the integrated design powers up identically every time - unlike microcontroller firmware that can be corrupted by brown-out events. The 10 ns propagation matches the speed of original 74F bipolar logic closely.
Được đề xuất
Test Equipment & JTAG Boundary-Scan Control
Beyond its own JTAG ISP interface, the EPM7160STC100-10 is widely used as a JTAG controller in test fixtures and boundary-scan test access port (TAP) aggregators for boards with mixed CPLD/FPGA/MCU devices. Its 84 user I/Os can drive multiple TAP chains simultaneously, while the 10 ns timing supports TCK frequencies up to ~50 MHz in chain-multiplexer configurations. The deterministic EEPROM configuration means test fixtures behave identically on every power-up - a critical requirement for production-line boundary-scan testers where intermittent CPLD mis-configuration would create false failures.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho EPM7160STC100-10 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | EPM7160STC100-10N | EPM7160STC100-7 | EPM7160STC100-15 | EPM7160STC100-6 | EPM7160STI100-10 | EPM7160STC100-10F |
|---|---|---|---|---|---|---|---|
| Package | TQFP-100 | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same | TQFP-100 - same |
| Brand | Intel (formerly Altera) | Intel | Intel | Intel | Intel | Intel | Intel |
| Macro Cells | 160 | 160 | 160 | 160 | 160 | 160 | 160 |
| User I/Os | 84 | 84 | 84 | 84 | 84 | 84 | 84 |
| Propagation Delay (tPD1) | 10 ns | 10 ns | 7 ns | 15 ns | 6 ns | 10 ns | 10 ns |
| Supply Voltage | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V | 5.0 V |
| Operating Temperature | 0C to +70C (commercial) | 0C to +70C | 0C to +70C | 0C to +70C | 0C to +70C | -40C to +85C (industrial) | 0C to +70C |
| RoHS Compliance | Non-RoHS (legacy) | RoHS compliant | Non-RoHS (legacy) | Non-RoHS (legacy) | Non-RoHS (legacy) | Non-RoHS (legacy) | Lead-free finish |
| Family | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S | MAX 7000S |
Bảo phân biệt quan trọng
- Largest logic capacity in MAX 7000S TQFP-100 family (vsEPM7128STC100-10)
- Balanced speed grade for mid-frequency designs (vsEPM7160STC100-7)
- Direct RoHS migration path available (vsEPM7160STC100-10N)
Ghi chú thiết kế
The EPM7160STC100-10 requires a stable 5.0 V supply with 4.75 V to 5.25 V tolerance per the MAX 7000S datasheet. Place 0.1 uF decoupling capacitors within 5 mm of every VCC pin (4 pins total: pins 21, 46, 71, 95) and add a 10 uF bulk capacitor near the package. During in-system programming via JTAG, VCC must rise monotonically - any brownout during configuration can leave the EEPROM in an indeterminate state requiring re-programming.
The 10 ns tPD1 propagation delay of the EPM7160STC100-10 requires careful PCB layout for clock and asynchronous signal routing. Keep global clock traces (GCLK1 pin 24, GCLK2 pin 49) shorter than 25 mm with 50 ohm characteristic impedance. Use series termination resistors (33-68 ohm) on clock outputs driving multiple loads. The 6 ns global clock setup time supports synchronous designs up to ~80 MHz internal frequency when clock skew is held under 1 ns across the chip.
Do not confuse the EPM7160STC100-10 (commercial temp, 10 ns) with the EPM7160STI100-10 (industrial -40C to +85C temp, 10 ns) - they are NOT interchangeable in production bins. The pin-compatible EPM7160SQC160-10 uses a 160-pin PQFP package, NOT 100-pin TQFP - attempting to substitute it on a TQFP-100 PCB will fail. When migrating legacy designs, always verify exact package code (STC=TQFP-100, SQC=PQFP-160, SLC=PLCC-84, SLI=PLCC-84 industrial) before ordering.
The TQFP-100 package has a 0.5 mm pitch and 1.6 mm height profile. Allow at least 0.2 mm solder mask expansion and use NSMD (non-solder mask defined) pads for reliable paste release during reflow. For hand-prototyping, use a TQFP-100 breakout board or adapter; the 0.5 mm pitch is below the practical limit for hand-soldering with a standard iron. A hot-air rework station with a TQFP nozzle is recommended for prototype rework.
Thông tin tuân thủ
Original EPM7160STC100-10 is non-RoHS leaded Altera part. The -10N suffix variant is RoHS compliant with lead-free finish. Pin-compatible RoHS variant EPM7160STC100-10N recommended for new EU-market designs.