LC4064C-10T48I - 64-Macrocell 125MHz CPLD | Lattice
MPN: LC4064C-10T48I ✗ Cuối đờiLC4064C-10T48I Tóm tắt
A complex programmable logic device is a programmable digital logic IC that combines an array of programmable logic and interconnect resources with configuration memory. Within the broader semiconductor hierarchy, the LC4064C belongs to the CPLD class, then to programmable logic devices and digital logic ICs. Unlike a mask-programmed PAL or GAL device, its logic configuration can be loaded or changed by a programmer, making it useful for prototyping, control, glue logic, and compact system integration.
The LC4064C-10T48I provides 64 macrocells and a stated 125 MHz maximum operating frequency in the 4000C family. Its in-system-programmable architecture supports 3.3 V, 2.5 V, and 1.8 V device variants identified in the family documentation. The 48-pin TQFP package is a surface-mount format with 0.5 mm pitch, and the exact ordering code denotes tray packaging with an industrial temperature designation.
The 4000C architecture combines programmable logic blocks with dedicated input and output structures, global clock resources, and programmable interconnect. This allows several related state machines, decoding functions, counters, and interface control functions to be consolidated in one device. Its deterministic CPLD implementation can also simplify timing analysis compared with a general-purpose microcontroller configuration containing multiple peripherals and interrupt paths.
Typical uses include industrial control and factory automation, instrument-panel logic, sensor conditioning, power-system sequencing, communications interface control, and embedded control support. In each case, the device is useful when the logic must be retained non-volatile, the design must boot without executing a firmware image, or a small deterministic controller is needed close to the associated interface circuitry.
PCB design should preserve the TQFP-48 land pattern, route programming access signals away from sensitive analog or high-speed nets, and validate all I/O assumptions against the device pin-description table. Because the documented architecture and I/O behavior determine the final system timing and power budget, designers should also check the manufacturer datasheet for electrical limits, clock requirements, and programming recommendations before release to production.
This product page consolidates the verified device identity, package information, programming characteristics, lifecycle status, and drop-in candidates into an engineering-focused reference. It also adds practical design notes, parameter comparisons, and sourcing guidance intended to make legacy CPLD evaluation and replacement planning faster.
Bộ thay thế dễ dàng lắp đặt cho LC4064C-10T48I — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LC4064C-10T48I (cùng hình factor và footprint) — khác nhau ở Device Family, Package Type.
LC4064C-10TN48I
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LC4064V-10T48I
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LC4064V-10TN48I
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LC4064ZE-7TN48I
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LC4064C-10T48I Tỷ lệ tối đa & tính chất điện
| Device Type | Complex Programmable Logic Device (CPLD) |
| Device Family | ispMACH 4000C |
| Macrocell Count | 64 macrocells |
| Maximum Operating Frequency | 125 MHz |
| Nominal Supply Voltage | 1.8 V |
| Supported Family Supply Voltages | 1.8 V, 2.5 V, or 3.3 V |
| Configuration Method | In-System Programmable (ISP) |
| Package Type | 48-pin TQFP |
| Package Pitch | 0.5 mm |
| Kiểu lắp đặt | Surface Mount |
| Shipping Format | Tray |
| Temperature Grade | Industrial |
Hướng dẫn cấu hình chân LC4064C-10T48I 0.5 mm
Cấu hình chân cho LC4064C-10T48I (0.5 mm gói). IC số này bao gồm chân GPIO, giao diện truyền thông (UART, SPI, I2C) và chân nguồn. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết các chức năng chân thay thế và tùy chọn cấu hình. Cực kỳ quan trọng cho thiết kế hệ thống tích hợp và lập trình PCB.
Không có dữ liệu chân cụ thể sẵn có cho LC4064C-10T48I.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LC4064C-10T48I phù hợp cho 6 Áp dụngs: Industrial Control and Automation, Instrumentation and Data Acquisition, Power-System Sequencing, Communications Interface Control, Sensor Signal Conditioning, Embedded System Support Logic.
Industrial Control and Automation
The LC4064C-10T48I is appropriate for deterministic factory-control logic that combines state machines, input decoding, sequencing, and output interlocks within 64 macrocells. Its 125 MHz maximum operating frequency provides ample timing headroom for many machine-control tasks, while in-system programming allows board-level configuration during production or maintenance. The 48-pin TQFP package supports compact surface-mount assemblies. Engineers should still validate every input threshold, output timing path, and supply condition against the device datasheet before connecting field wiring or safety-related circuits.
Được đề xuất
Instrumentation and Data Acquisition
In laboratory and process-instrumentation systems, the LC4064C-10T48I can consolidate measurement sequencing, mode control, alarm decoding, and interface timing into one programmable logic device. The 64-macrocell density is suitable for several small state machines without moving the design into a larger FPGA. Its non-volatile configuration also supports repeatable standalone operation after power is restored. Design care is needed for analog grounding, clock distribution, and isolation boundaries, because the CPLD coordinates digital functions but does not replace front-end signal conditioning.
Được đề xuất
Power-System Sequencing
The LC4064C-10T48I can implement rail-ordering, enable-control, monitor, and fault-latch logic around a multi-rail power system. Its 125 MHz maximum operating frequency allows rapid sequencing decisions compared with many low-speed supervisory mechanisms, while 64 macrocells can support multiple independent control paths. A real implementation should define fail-safe states, constrain unused outputs, and account for power-up behavior before programming is applied. The CPLD should not be the sole protection element where a hardware fault must be handled independently of programmable logic.
Được đề xuất
Communications Interface Control
The LC4064C-10T48I is useful as protocol glue logic between sensors, converters, memories, and host processors. Typical duties include framing, byte assembly, command decoding, parity generation, and programmable timing delays. The 64-macrocell capacity allows these functions to be consolidated while the 125 MHz figure supports reasonably fast control paths. For communication links, engineers must define clock-domain boundaries, metastability treatment, I/O voltage compatibility, and timing margins in the system design rather than treating the CPLD as a protocol controller with fixed standard compliance.
Được đề xuất
Sensor Signal Conditioning
The LC4064C-10T48I can coordinate digital filtering, threshold comparison, calibration tables, sampling control, and alarm outputs in a sensor interface. Its programmable architecture allows timing constants and control sequences to be changed without changing the PCB, while the non-volatile configuration preserves selected calibration behavior after power cycling. Performance depends on the external sensors and analog front end because the CPLD processes digital logic rather than directly conditioning precision analog signals. Review I/O thresholds and ground-return paths with the complete analog design.
Được đề xuất
Embedded System Support Logic
The LC4064C-10T48I can serve as deterministic companion logic beside a microcontroller, handling reset coordination, power gating, watchdog supervision, interrupt routing, peripheral chip selection, or bus-cycle decoding. This arrangement preserves firmware flexibility while offloading small, timing-sensitive tasks into non-volatile programmable logic. The 48-pin TQFP footprint is manageable in a mixed-signal board, but designers must define ownership of every signal to prevent contention between the microcontroller and CPLD. Post-reset and brownout behavior should be verified for every cross-device path.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LC4064C-10T48I — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LC4064C-10TN48I | LC4064V-10T48I | LC4064V-10TN48I | LC4064ZE-7TN48I |
|---|---|---|---|---|---|
| Package | 48-pin TQFP | 48-pin package | 48-pin TQFP | 48-pin package | 48-pin package |
| Brand | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor | Lattice Semiconductor |
| Device Family | ispMACH 4000C | ispMACH 4000C | LC4064V | LC4064V | LC4064ZE |
| Speed Designator | 10 | 10 | 10 | 10 | 7 |
Bảo phân biệt quan trọng
- Directly preserves the original C-generation device identity (vsLC4064V-10T48I)
- Provides a documented 125 MHz maximum operating frequency (vsLC4064ZE-7TN48I)
- Uses the 48-pin TQFP format specified for the original design (vsLC4064C-10TN48I)
- Combines compact logic density with non-volatile configuration (vsATF16LV8C-10JU)
Ghi chú thiết kế
Route the programming interface and clock inputs according to the manufacturer pin-description and recommended-layout sections. Keep programming traces away from switching nodes and sensitive analog inputs, use a continuous ground reference beneath the device where the board stack-up permits, and place decoupling capacitors close to the associated supply pins. Confirm the actual pin assignments in the LC4064C datasheet before releasing artwork.
Do not treat a similar LC4064 suffix as proof of electrical equivalence. Compare device generation, speed code, temperature code, package drawing, I/O standards, supply limits, macrocell allocation, and programming architecture. The four listed candidates are drop-in review candidates, but each legacy substitution should be recompiled and timing-checked against the original design before production use.
Decouple each applicable supply rail locally and validate startup, shutdown, and brownout behavior in the assembled board. The device supports multiple voltage options across the family, so the ordering code and exact datasheet must determine the operating values. Where the CPLD controls sequencing for other circuits, define conservative output states before configuration is loaded and prevent unsafe outputs from being enabled solely through a programmable state machine.
Use the global clock and interconnect resources as directed in the device documentation, and constrain external timing paths according to the actual system clock rather than the 125 MHz maximum operating frequency. That headline figure describes device capability under specified conditions; it does not guarantee the same edge rate for every board-level path. Check setup, hold, skew, and output-load assumptions before assigning a high-speed clock to an external peripheral.
Thông tin tuân thủ
The device is identified as an industrial-temperature LC4064C CPLD, but specific RoHS, REACH, lead-free, halogen-free, and conflict-minerals declarations require confirmation from current manufacturer or lot documentation.