LM224NG4 - Quad 1.2MHz Op Amp | Texas Instruments
MPN: LM224NG4 ✓ Hoạt độngLM224NG4 Tóm tắt
An operational amplifier is an analog signal-processing IC that amplifies the difference between its inverting and non-inverting inputs. Its high open-loop gain, negative-feedback operation, and internal compensation allow it to function as an inverting amplifier, non-inverting amplifier, voltage follower, comparator-style interface, or active filter building block. The LM224NG4 belongs to the broad operational-amplifier hierarchy within analog and linear integrated circuits.
The key headline specifications are four amplifier circuits in one package, a 1.2 MHz gain-bandwidth product, and a 14-pin DIP package. The LM224 family is designed for operation from a single supply or split supplies, with a documented supply-voltage range of 3 V to 32 V. This combination supports economical industrial, instrumentation, sensor, and test-equipment designs where four general-purpose amplifiers are needed on one board.
The quad organization reduces component count and PCB area compared with four separate single operational amplifiers. Each amplifier has independent inverting and non-inverting inputs, an output, and a power connection, allowing unused amplifier sections to be configured according to standard feedback arrangements. Internal frequency compensation removes the need for an external dominant-pole capacitor in typical closed-loop uses.
Typical applications include low-frequency instrumentation amplifiers, transducer-signal conditioning, current-to-voltage conversion, sensor interfaces, sample-and-hold stages, active filtering, and general industrial control. The 1.2 MHz gain-bandwidth product is most suitable for low-to-moderate-frequency signal paths rather than high-speed video or RF amplification. Users should also account for input common-mode range, output swing, input bias current, and supply-current limits when defining the usable signal range.
For a new 14-pin DIP design, verify the pin arrangement and operating limits in the manufacturer datasheet before layout. Place bypass capacitors close to the supply pins, keep sensitive inverting-input traces short, and connect unused amplifier inputs to a defined potential rather than allowing them to float. Thermal design should consider the dissipation from all four amplifiers and the maximum ambient and junction temperatures permitted for the purchased package variant.
This page combines the verified LM224NG4 device identity with application guidance, drop-in comparison criteria, package considerations, and design notes that help engineers evaluate the part before committing it to a 14-DIP board layout.
Bộ thay thế dễ dàng lắp đặt cho LM224NG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM224NG4 (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Package, Compensation, Maximum Supply Voltage, Number of Circuits.
LM224N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224AN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224NG
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224AN
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM224NG4 Tỷ lệ tối đa & tính chất điện
| Amplifier Type | General-purpose operational amplifier |
| Number of Circuits | 4 circuits |
| Gain-Bandwidth Product | 1.2 MHz |
| Supply Voltage Range | 3 V to 32 V |
| Supply Configuration | Single supply or split supply |
| Compensation | Internally frequency compensated |
| Package Type | 14-pin DIP (0.300 inch, 7.62 mm pitch) |
| Package Family | PDIP |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân LM224NG4 pdip
Cấu hình chân cho LM224NG4 (pdip gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM224NG4.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM224NG4 phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Current-to-Voltage Conversion, Active Audio and Control Filtering, Test and Measurement Equipment, Battery and Supply Monitoring, Data Acquisition Front End.
Industrial Sensor Signal Conditioning
LM224NG4 fits low-frequency industrial sensor interfaces because four independently usable amplifiers can amplify, buffer, and filter one sensor chain in a 14-pin DIP package. Its 3 V to 32 V operating range accommodates common industrial supply rails, while the 1.2 MHz gain-bandwidth product is adequate for many process and position sensors. Use one section for front-end amplification and another for an active low-pass filter, then verify input offset, bias current, common-mode range, and output swing against the sensor output.
Current-to-Voltage Conversion
LM224NG4 is well suited to precision current-to-voltage conversion in instrumentation and test circuits. Four amplifier sections allow multiple conversion or measurement channels to share one package, reducing board area compared with discrete single amplifiers. The 1.2 MHz gain-bandwidth product supports low-to-moderate measurement bandwidth, and the 3 V to 32 V supply range supports single- and split-supply architectures. Select feedback resistors for the required gain and confirm that source current, output swing, and input offset remain within the operating limits.
Active Audio and Control Filtering
LM224NG4 can implement active filters and audio-control signal paths with bandwidth below the amplifier's 1.2 MHz gain-bandwidth product. Multiple amplifier sections allow Sallen-Key or multiple-feedback stages to be built without using four separate packages. The device's 3 V to 32 V supply range accommodates many control boards, but passive-component tolerances, amplifier noise, slew rate, and output loading determine the actual response. Check the gain-bandwidth and common-mode limits before extending the filter beyond its intended low-frequency range.
Test and Measurement Equipment
LM224NG4 is useful in test and measurement equipment requiring buffered inputs, programmable gain stages, or active filtering around low-frequency sources. Its four internal amplifiers provide independent channels for source buffering, gain conversion, offset correction, and output isolation. The 1.2 MHz gain-bandwidth product suits many precision low-frequency instruments rather than wideband scopes or arbitrary-waveform output stages. Validate input capacitance, output drive, stability, and supply noise performance with the intended source and load impedances.
Battery and Supply Monitoring
LM224NG4 can amplify low-level monitoring signals in battery-powered or industrial power systems because it operates from a supply as low as 3 V and contains four amplifier sections. The parts may buffer sensed voltages, create differential measurements, or drive comparator inputs, subject to the common-mode and output-swing limits. Because the quad package can consume current even when only some sections are active, analyze total quiescent demand and battery life. A series input limiter may also be required when the monitored node can exceed the amplifier's supply rails.
Data Acquisition Front End
LM224NG4 is suitable for conditioning outputs from low-speed sensors and converters in a data-acquisition front end. One section can amplify a bipolar or unipolar sensor signal, another can provide gain or offset adjustment, and additional sections can filter or buffer the result. The 1.2 MHz gain-bandwidth product is suitable for many multiplexed low-frequency acquisition channels, while the 3 V to 32 V range simplifies interface design. Confirm settling behavior, source impedance, channel isolation, and the applicable conversion-system sampling requirements.
Dữ liệu tham khảo kỹ thuật cho LM224NG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM224N | LM224AN | LM224NG | LM224N | LM224AN |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | onsemi | onsemi | onsemi |
| Package | 14-DIP (0.300 inch, 7.62 mm pitch) | 14-DIP (0.300 inch, 7.62 mm pitch) - same | 14-DIP (0.300 inch, 7.62 mm pitch) - same | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same |
Bảo phân biệt quan trọng
- Four general-purpose amplifiers in one through-hole package (vsLM224NG)
- Exact Texas Instruments family continuity (vsLM224N)
- Pin- and package-consistent family option (vsLM224AN)
Ghi chú thiết kế
Decouple each supply rail close to the device with a local bypass capacitor and adequate ground-plane return. Estimated: if the total quiescent current is IQ and the supply is VS, the static device power is approximately VS × IQ; add output-stage dissipation from the driven channels and compare the result with the package power rating. Place the capacitor where its ground connection shares a low-impedance path with the amplifier supply ground.
Keep the inverting-input node physically short because feedback and parasitic capacitance at that node can alter stability and settling. Route outputs away from high-impedance inputs, use a continuous ground plane, and avoid long parallel traces that can couple output currents into sensitive inputs. Use the numbered manufacturer pin diagram when laying out the 14-pin DIP because rotation or mirroring can connect power and signal pins incorrectly.
Do not assume that the 3 V to 32 V supply range defines the allowable signal range. Check common-mode input limits, output swing, input offset, bias current, output-current capability, and operating temperature. Unused amplifier inputs must be tied to a defined potential within the input range. If a sensor output can exceed the supply rails, add suitable input protection or isolation before the amplifier package.
The 1.2 MHz gain-bandwidth product limits useful closed-loop bandwidth according to the required noise gain and stability margin. Keep normal closed-loop gains low enough for stable operation with the selected feedback network, and test source impedance, capacitive loading, and output-load effects. For active filters, calculate component tolerances and verify settling time when operating close to the amplifier's bandwidth limit.
Thông tin tuân thủ
Compliance status was not stated in the manufacturer or distributor information for this device. Confirm the current declarations and exact ordering code with Texas Instruments before production release.