LM2876TF - 40W Mono Class AB Amplifier | Texas Instruments
MPN: LM2876TF ✓ Hoạt độngLM2876TF Tóm tắt
An audio power amplifier is an integrated circuit that increases the voltage and current capability of an audio signal so it can drive a loudspeaker, subwoofer, or other high-impedance acoustic load. The LM2876 belongs to the amplifier IC hierarchy, where Class AB describes the output-stage operating method: the amplifier conducts during both halves of the audio waveform while minimizing crossover distortion. It also provides SPiKe protection, described by Texas Instruments as dynamically protecting the device against instantaneous thermal peaks.
The principal specifications are 40 W continuous average output power, operation from 20 V to 60 V, and compatibility with an 8 ohm load. The LM2876 is a mono design intended for single-channel audio amplification. Its 0.1% THD+N rating covers 20 Hz to 20 kHz, providing a defined distortion and bandwidth reference when comparing it with other high-power audio amplifiers.
Internally, the LM2876 combines Class AB output operation with a mute function and SPiKe thermal protection. The protection system is intended to react to instantaneous power events more effectively than a basic thermal shutdown alone. The isolated TO-220-11 construction supports conventional through-hole assembly and provides a mechanically robust option for audio equipment where heatsinking and grounding layout are important.
Typical uses include monoblock subwoofer amplifiers, powered speaker systems, hi-fi amplifier output stages, home-theater audio power amplifiers, and industrial audio drivers. In each case, the amplifier requires a stable high-voltage supply, appropriate output filtering for the selected load, adequate copper area and thermal management, and careful separation of input, output, and power-ground paths.
Design should begin with the 40 W continuous-power target rather than the absolute device rating. A practical implementation must provide enough supply headroom, verify thermal conditions at the selected load impedance, and account for the difference between continuous music power and short-duration peaks. The mute and SPiKe features add control and protection functions, but successful operation still depends on correct board layout and thermal design.
This page combines the manufacturer’s core LM2876 specifications with purchasing guidance, application-focused engineering guidance, and a packaging-aware replacement assessment. It is intended to help designers determine whether the LM2876TF suits a high-power mono audio stage and how to verify board-level thermal, electrical, and sourcing requirements before committing to a design.
Bộ thay thế dễ dàng lắp đặt cho LM2876TF — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2876TF (cùng hình factor và footprint) — khác nhau ở Load Impedance, Number of Pins, Supply Voltage Range.
LM2876TF/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2876TF Tỷ lệ tối đa & tính chất điện
| Product Type | Mono audio power amplifier IC |
| Manufacturer | Texas Instruments |
| Amplifier Class | Class AB |
| Number of Channels | 1 channel |
| Continuous Average Output Power | 40 W |
| Load Impedance | 8 ohm |
| Supply Voltage Range | 20 V to 60 V |
| Total Harmonic Distortion Plus Noise | 0.1% at 40 W into 8 ohm from 20 Hz to 20 kHz |
| Frequency Range | 20 Hz to 20 kHz |
| Mute Function | Yes |
| Protection Technology | SPiKe Self Peak Instantaneous Temperature protection |
| Package Type | TO-220-11 isolated package |
| Số lượng chân | 11 pins |
| Kiểu lắp đặt | Through-hole |
Hướng dẫn cấu hình chân LM2876TF to-220-11 isolated package
Cấu hình chân cho LM2876TF (to-220-11 isolated package gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2876TF.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2876TF phù hợp cho 6 Áp dụngs: Monoblock Subwoofer Amplifier, Powered Speaker Output Stage, Home Theater Amplifier, Hi-Fi Stereo Amplifier, Industrial Audio Driver, Audio Test and Measurement Amplifier.
Monoblock Subwoofer Amplifier
The LM2876TF fits a monoblock subwoofer output stage because it is specified for 40 W continuous average power into an 8 ohm load with 0.1% THD+N from 20 Hz to 20 kHz. Place the amplifier in the final power stage, then add the crossover, input filtering, offset control, and output network required by the selected loudspeaker. The 20 V to 60 V supply can support the output voltage needed for high-power operation, while SPiKe protection helps manage instantaneous thermal events. The enclosure and heatsink must dissipate continuous Class AB losses rather than only short-lived musical peaks.
Được đề xuất
Powered Speaker Output Stage
For a powered bookshelf or floor-standing speaker, the LM2876TF can provide a 40 W Class AB mono output stage from a 20 V to 60 V supply. The 8 ohm load rating aligns with common passive speaker configurations, while the stated 0.1% THD+N across 20 Hz to 20 kHz provides a clear distortion target for amplifier selection. The LM2876TF is placed after preamplification and volume control, with the signal level adjusted so the amplifier does not enter clipping. A thermally sized heatsink and low-impedance output routing are essential because sustained high-level music can raise dissipation substantially.
Được đề xuất
Home Theater Amplifier
The LM2876TF can serve as a mono power channel in a home-theater or multichannel audio amplifier, especially where each channel drives an 8 ohm loudspeaker or speaker group. Its 40 W continuous average capability and 20 Hz to 20 kHz distortion specification suit audio-band amplification, while mute supports controlled channel or system enable functions. The designer should coordinate the device with a preamplifier that prevents excessive input drive, implement channel-specific gain structure, and verify thermal performance in a closed enclosure. SPiKe protection addresses instantaneous thermal peaks but does not replace speaker DC blocking, overload control, or system-level protection.
Được đề xuất
Hi-Fi Stereo Amplifier
In a high-power stereo design, two LM2876TF devices can form a left and right Class AB output pair, each rated to deliver 40 W continuous average power into an 8 ohm load. The device operates from a 20 V to 60 V supply, which makes it appropriate for a dedicated high-voltage power-transformer and rectifier arrangement. Low THD+N is relevant to preserving small musical signals near the output stage. Symmetrical layout, carefully routed feedback and output paths, and independent channel testing are important. Each package requires adequate heatsinking, and the bias and feedback components must follow the manufacturer reference circuit.
Được đề xuất
Industrial Audio Driver
The LM2876TF is suitable for a dedicated industrial or commercial audio driver when the load is an 8 ohm speaker and the enclosure can accommodate its heat dissipation. The 40 W continuous output rating supports stronger sound-pressure levels than low-power headphone or line-level amplifiers, while the mute input can support panel-driven channel control. Industrial systems may also require DC-offset prevention, over-temperature shutdown, fuse coordination, and robust output protection around the amplifier. The 20 V to 60 V supply design must include regulation adequate for peak audio demand, while SPiKe handles the amplifier’s instantaneous thermal stress.
Được đề xuất
Audio Test and Measurement Amplifier
The LM2876TF can provide a high-power Class AB output stage for a loudspeaker test fixture, acoustic measurement system, or laboratory audio driver. Its 0.1% THD+N specification from 20 Hz to 20 kHz and 40 W continuous average output into 8 ohms provide a useful starting point for controlled test signals. The amplifier should be operated within the stated supply range, with output protection and DC blocking designed for the fixture. Because distortion and thermal behavior depend on signal level and frequency, use controlled test waveforms and verify the thermal design under sustained operation rather than assuming nominal output power applies to every waveform.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2876TF — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2876TF/NOPB |
|---|---|---|
| Brand | Texas Instruments | Texas Instruments |
| Package | TO-220-11 | TO-220-11 - same |
| Amplifier Type | Mono Class AB audio power amplifier | Mono Class AB audio power amplifier |
| Continuous Output Power | 40 W | 40 W |
| Load Impedance | 8 ohm | 8 ohm |
| Supply Voltage Range | 20 V to 60 V | 20 V to 60 V |
| THD+N | 0.1% from 20 Hz to 20 kHz under stated test conditions | 0.1% from 20 Hz to 20 kHz under stated test conditions |
| Number of Channels | 1 channel | 1 channel |
| Mute Function | Yes | Yes |
| Protection | SPiKe instantaneous-temperature protection | SPiKe instantaneous-temperature protection |
Bảo phân biệt quan trọng
- Full 40 W Class AB mono output in an audio power-amplifier package (vsLM2876TF/NOPB)
- High-voltage supply capability for high-power audio stages (vsLM2876TF/NOPB)
- Integrated mute and SPiKe protection functions (vsLM2876TF/NOPB)
Ghi chú thiết kế
Size the heatsink for continuous Class AB dissipation rather than the 40 W output rating alone. Estimated: amplifier dissipation is the DC power delivered to the load plus transistor, bias, and switching losses, with actual junction temperature determined by package thermal resistance, heatsink resistance, copper area, airflow, and ambient temperature. Validate the worst-case music condition in the intended enclosure and confirm the operating-temperature limit against the manufacturer datasheet.
Use the manufacturer reference layout for the TO-220-11 device, especially because this 11-lead package is not equivalent to a standard three-lead TO-220. Keep the high-current supply and speaker-output paths short, use adequate copper width, and minimize loop area. Place input, feedback, and ground returns away from output and rectifier currents. Confirm every physical pin function against the package-specific pin-description table before fabrication.
Design the 20 V to 60 V supply for the output voltage swing, regulation, and current required at 40 W into 8 ohms. The ideal sinusoidal voltage for 40 W into 8 ohms is approximately 17.9 Vrms, but real Class AB output stages require additional supply headroom. Use transformer, rectifier, reservoir-capacitor, and protection arrangements based on the manufacturer reference design, and account for startup, line variation, and inrush behavior.
Do not treat SPiKe protection as a substitute for loudspeaker protection. DC offset, short circuits, excessive temperature, and loudspeaker overload may require separate system-level protection. Also do not substitute a standard TO-220 pinout for the TO-220-11 arrangement, and do not infer the correct mute polarity or signal-ground connection from a generic three-pin power-amplifier convention. Use the LM2876 manufacturer pin table and application circuit as the wiring authority.
Thông tin tuân thủ
The LM2876TF/NOPB ordering designation identifies a lead-free option, but no explicit RoHS, REACH, halogen-free, or conflict-minerals declaration is included in the referenced product information. Automotive qualification is not applicable to this audio power amplifier.