LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments
MPN: LM2903BQDRQ1 ✓ Hoạt độngLM2903BQDRQ1 Tóm tắt
A comparator is an analog signal-processing IC that compares two input voltages and produces a digital output indicating which input is higher. Comparators belong to the broader amplifier IC category and are commonly used as threshold detectors, sensor interfaces, overvoltage monitors, and control-loop decision elements. Unlike a general-purpose operational amplifier, the LM2903BQDRQ1 is intended primarily for open-loop voltage comparison rather than precision closed-loop amplification.
The primary features of the LM2903BQDRQ1 are its dual differential input architecture, open-collector output stage, rail-to-rail input capability, and broad supply-voltage range. The open-collector outputs require an external pull-up resistor, allowing the output state to be set by the external pull-up voltage. This arrangement is useful when interfacing with automotive logic, transistor-based level conversion, relay drivers, or multiple devices sharing a wired bus. Its -40 °C to +125 °C temperature range supports applications across industrial, automotive, and other extended-temperature environments.
The LM2903B-Q1 family is described by Texas Instruments as a next-generation version of the industry-standard LM2903-Q1 comparator family. Its stated improvements include lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance, together with drop-in replacement convenience. The target MPN combines these automotive-grade features in the 8-SOIC package identified by ordering code D.
Typical uses include battery-pack threshold detection, automotive sensor conditioning, overvoltage and undervoltage protection, industrial control inputs, window or level monitoring, and logic-level translation. In each case, the two comparator channels can monitor independent thresholds or operate as complementary detectors. The open-collector architecture also permits a system designer to select the pull-up voltage and current rather than being restricted to a fixed push-pull output voltage.
When laying out a board, place the pull-up resistor close to the open-collector output and keep comparator input traces short to reduce susceptibility to injected noise. Confirm output-current limits, input common-mode behavior, supply sequencing, and logic thresholds in the manufacturer datasheet before finalizing the design. Consider a device with push-pull outputs when an external pull-up is undesirable, or verify an alternate comparator carefully when its output architecture or input range differs.
This page combines the manufacturer’s automotive comparator information, verified ordering details, and practical drop-in guidance. It helps engineers identify the correct package, temperature grade, output type, and replacement options while emphasizing the electrical checks that matter during schematic and PCB design.
Bộ thay thế dễ dàng lắp đặt cho LM2903BQDRQ1 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903BQDRQ1 (cùng hình factor và footprint) — khác nhau ở Package, Number of Channels, Output Type, Automotive Qualification, Input Bias Current.
LM2903DR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903BIDR
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903BIDRQ1
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM2903QDRQ1
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2903BQDR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM2903BQDRQ1 Tỷ lệ tối đa & tính chất điện
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| Kiểu đầu ra | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| Supply Voltage Range | ±18 V or 36 V total |
| Hộp | SOIC (D), 8 pins |
| Khoảng nhiệt độ hoạt động | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 |
| Output Pull-Up Requirement | External pull-up resistor required |
| Improved ESD Performance | 2 kV |
| Kiểu lắp đặt | Surface mount |
Hướng dẫn cấu hình chân LM2903BQDRQ1 soic (d), 8 pins
Cấu hình chân cho LM2903BQDRQ1 (soic (d), 8 pins gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2903BQDRQ1.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2903BQDRQ1 phù hợp cho 6 Áp dụngs: Automotive Battery Threshold Detection, Overvoltage and Undervoltage Protection, Industrial Sensor Interfacing, Automotive Sensor and Actuator Conditioning, Relay and Solenoid Drive Logic, Logic Level Translation.
Automotive Battery Threshold Detection
The LM2903BQDRQ1 fits automotive battery-pack monitoring because it combines differential inputs, open-collector outputs, and operation across -40 °C to +125 °C. Place one channel across a divided battery voltage and the other across a precise reference to detect overvoltage or undervoltage conditions. Its external pull-up can be tied to the vehicle logic supply, while the wide ±18 V or 36 V total supply capability supports protected industrial-style sensing paths. Because the output is open collector, multiple detection nodes can be combined where appropriate. Confirm input overvoltage protection and transient performance in the final power-distribution network.
Được đề xuất
Overvoltage and Undervoltage Protection
The LM2903BQDRQ1 can implement independent protection decisions by comparing divided supply voltages against a reference. Its dual-channel architecture allows one section to monitor an upper limit while the other monitors a lower limit, reducing the number of discrete comparator assemblies required. The open-collector outputs support direct interface to an enable, shutdown, or fault input through an external pull-up. The LM2903B-Q1 generation is described as offering lower offset voltage and lower propagation delay than the earlier LM2903 family, which are useful traits in protection systems. Validate threshold accuracy, response time, and output-current limits against the system thresholds.
Được đề xuất
Industrial Sensor Interfacing
The LM2903BQDRQ1 is useful for converting analog sensor conditions into discrete control decisions. A resistive divider can translate a sensor output into the differential input range, and the comparator then generates an open-collector event when the sensing threshold is crossed. Rail-to-rail input operation helps the design use much of the available signal range, while the -40 °C to +125 °C rating supports extended-temperature industrial equipment. Choose the pull-up voltage to match the controller domain and size the resistor for the required rise time. Sensor hysteresis or filtering should be added where electrical noise could cause repeated threshold transitions.
Được đề xuất
Automotive Sensor and Actuator Conditioning
The LM2903BQDRQ1 supports threshold decisions around automotive sensors, switches, and actuator feedback loops. Its dual differential inputs permit comparison against a local reference, and the open-collector output can pull down a control line or drive a subsequent transistor stage. The automotive LM2903B-Q1 positioning, AEC-Q100 identification, and extended temperature range make it appropriate for electronics located near harsh vehicle environments. Ensure the surrounding divider, reference, and protection components also meet their respective automotive requirements. The comparator should sit behind appropriate transient protection when connected to external wiring.
Được đề xuất
Relay and Solenoid Drive Logic
The LM2903BQDRQ1 can create a low-side relay or solenoid control signal by comparing a command voltage with a threshold and using the open-collector output to drive an external transistor. This arrangement prevents the comparator from carrying the full actuator current and lets the pull-up voltage match the control logic. Differential inputs are valuable when the command is referenced to a remote or offset signal node. The LM2903B-Q1 family’s stated improvements in propagation delay and input bias current support responsive threshold decisions. Include transistor base current, flyback protection, and contactor-specific voltage ratings in the complete driver design.
Được đề xuất
Logic Level Translation
The LM2903BQDRQ1 can translate between voltage domains by using its open-collector output with a pull-up to the destination logic voltage. When the input comparator detects the appropriate logic state, it releases the pulled-up line or pulls it down, allowing a higher-voltage or lower-voltage domain to be read by the receiving circuit. This arrangement is particularly useful because the output-high level is set by the external resistor rather than a fixed internal voltage. Keep the pull-up current within the output rating and check the destination receiver’s thresholds. Input and output absolute-maximum limits must also be checked for every translated voltage.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2903BQDRQ1 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2903DR | LM2903BIDR | LM2903BIDRQ1 | LM2903QDRQ1 | LM2903BQDR |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Automotive Qualification | AEC-Q100 | Not stated for this ordering code | Not stated for this ordering code | Q1 ordering family | Q1 ordering family | Non-Q1 ordering suffix |
| Family Generation | LM2903B-Q1 with lower offset, supply current, bias current, propagation delay, and improved 2 kV ESD performance | LM2903 family | LM2903B family | LM2903B-Q1 family | LM2903-Q1 family | LM2903B-Q1 family |
Bảo phân biệt quan trọng
- Automotive LM2903B-Q1 family positioning (vsLM2903QDRQ1)
- Documented drop-in package compatibility (vsLM2903DR)
- Extended-temperature automotive specification (vsLM2903BIDR)
Ghi chú thiết kế
Do not treat the open-collector output as a push-pull logic output. Add a pull-up resistor to the required logic rail and confirm that its maximum current, rise time, and power dissipation are acceptable. If a redesign removes the resistor, the output will remain unable to source current in the high state. Also check whether downstream circuitry requires wired-AND behavior or isolated high-side signaling before reusing this topology.
Place the pull-up resistor close to the LM2903BQDRQ1 output pin to limit the trace length carrying the rising edge. Keep differential input traces short, route them away from switching nodes, and connect the ground return directly to the device ground pin. If the comparator monitors a remote or high-voltage node, place divider and protection components near the connector and provide a defined low-impedance return path to minimize differential pickup.
Add controlled hysteresis around the comparison threshold when slow input transitions or output noise could cause repeated switching. Positive feedback can provide hysteresis, but the resistor network must preserve the available differential input range. Verify offset and propagation delay at the actual temperature and supply voltage, and do not rely solely on nominal values when the decision affects protection, braking, or another safety-relevant function.
Decouple the comparator supply with a local ceramic capacitor and place it adjacent to the supply and ground pins. Keep the supply return current away from sensitive input and output-return paths. When using single-supply operation, confirm that the comparator inputs, outputs, and pull-up rail remain within the datasheet limits under startup, shutdown, and transient conditions; rail-to-rail input wording does not override absolute-maximum ratings.
Thông tin tuân thủ
Texas Instruments identifies LM2903B-Q1 as an automotive family and the LM2903BQDRQ1 ordering entry as AEC-Q100. Other compliance declarations are not stated in the cited product information.