LM2903BQDRQ1 - Dual Rail-to-Rail Comparator | Texas Instruments
MPN: LM2903BQDRQ1 ✓ فعالLM2903BQDRQ1 نمای کلی
A comparator is an analog signal-processing IC that compares two input voltages and produces a digital output indicating which input is higher. Comparators belong to the broader amplifier IC category and are commonly used as threshold detectors, sensor interfaces, overvoltage monitors, and control-loop decision elements. Unlike a general-purpose operational amplifier, the LM2903BQDRQ1 is intended primarily for open-loop voltage comparison rather than precision closed-loop amplification.
The primary features of the LM2903BQDRQ1 are its dual differential input architecture, open-collector output stage, rail-to-rail input capability, and broad supply-voltage range. The open-collector outputs require an external pull-up resistor, allowing the output state to be set by the external pull-up voltage. This arrangement is useful when interfacing with automotive logic, transistor-based level conversion, relay drivers, or multiple devices sharing a wired bus. Its -40 °C to +125 °C temperature range supports applications across industrial, automotive, and other extended-temperature environments.
The LM2903B-Q1 family is described by Texas Instruments as a next-generation version of the industry-standard LM2903-Q1 comparator family. Its stated improvements include lower offset voltage, higher supply-voltage capability, lower supply current, lower input bias current, lower propagation delay, and improved 2 kV ESD performance, together with drop-in replacement convenience. The target MPN combines these automotive-grade features in the 8-SOIC package identified by ordering code D.
Typical uses include battery-pack threshold detection, automotive sensor conditioning, overvoltage and undervoltage protection, industrial control inputs, window or level monitoring, and logic-level translation. In each case, the two comparator channels can monitor independent thresholds or operate as complementary detectors. The open-collector architecture also permits a system designer to select the pull-up voltage and current rather than being restricted to a fixed push-pull output voltage.
When laying out a board, place the pull-up resistor close to the open-collector output and keep comparator input traces short to reduce susceptibility to injected noise. Confirm output-current limits, input common-mode behavior, supply sequencing, and logic thresholds in the manufacturer datasheet before finalizing the design. Consider a device with push-pull outputs when an external pull-up is undesirable, or verify an alternate comparator carefully when its output architecture or input range differs.
This page combines the manufacturer’s automotive comparator information, verified ordering details, and practical drop-in guidance. It helps engineers identify the correct package, temperature grade, output type, and replacement options while emphasizing the electrical checks that matter during schematic and PCB design.
جایگزینهای drop-in برای LM2903BQDRQ1 — همان پکیج، سازگار پینبهپین. قطعات با پکیج متفاوت که نیاز به تغییر PCB دارند مستثنی هستند.
گونهها در این سری
مدلهای همسری که جایگزین مستقیم هستند برای LM2903BQDRQ1 (همان فرمفاکتور و فوتپرینت) — متفاوت در Package, Number of Channels, Output Type, Automotive Qualification, Input Bias Current.
LM2903DR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2903BIDR
✅ جایگزین مستقیمبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2903BIDRQ1
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LM2903QDRQ1
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشدهبرای قیمت تماس بگیرید
مشاهده دیتاشیت ←LM2903BQDR
✅ جایگزین مستقیم ⚠️ مشخصات تأییدنشده📋 جایگزین مرجع (خارج از کاتالوگ)
LM2903BQDRQ1 حداکثر مقادیر مجاز و مشخصات الکتریکی
| Comparator Type | Dual differential comparator |
| Number of Channels | 2 channels |
| نوع خروجی | Open-collector |
| Input Common-Mode Range | Rail-to-rail |
| Supply Voltage Range | ±18 V or 36 V total |
| بستهبندی | SOIC (D), 8 pins |
| محدوده دمای کاری | -40 °C to +125 °C |
| Automotive Qualification | AEC-Q100 |
| Output Pull-Up Requirement | External pull-up resistor required |
| Improved ESD Performance | 2 kV |
| نوع نصب | Surface mount |
راهنمای پیکربندی پین LM2903BQDRQ1 soic (d), 8 pins
پیکربندی پین برای LM2903BQDRQ1 (پکیج soic (d), 8 pins). این قطعه آنالوگ دارای پینهای ورودی، خروجی و تغذیه است. برای پیکربندیهای پین offset null، جبرانسازی و فعالسازی به دیتاشیت سازنده مراجعه کنید. ایدهآل برای مدارهای شرطیسازی سیگنال و تقویتکننده.
داده پینآوت تفصیلی موجود نیست برای LM2903BQDRQ1.
به دیتاشیت برای پیکربندی کامل پینها.
کاربردهای معمول
LM2903BQDRQ1 مناسب است برای 6 کاربردs: Automotive Battery Threshold Detection, Overvoltage and Undervoltage Protection, Industrial Sensor Interfacing, Automotive Sensor and Actuator Conditioning, Relay and Solenoid Drive Logic, Logic Level Translation.
Automotive Battery Threshold Detection
The LM2903BQDRQ1 fits automotive battery-pack monitoring because it combines differential inputs, open-collector outputs, and operation across -40 °C to +125 °C. Place one channel across a divided battery voltage and the other across a precise reference to detect overvoltage or undervoltage conditions. Its external pull-up can be tied to the vehicle logic supply, while the wide ±18 V or 36 V total supply capability supports protected industrial-style sensing paths. Because the output is open collector, multiple detection nodes can be combined where appropriate. Confirm input overvoltage protection and transient performance in the final power-distribution network.
پیشنهادی
Overvoltage and Undervoltage Protection
The LM2903BQDRQ1 can implement independent protection decisions by comparing divided supply voltages against a reference. Its dual-channel architecture allows one section to monitor an upper limit while the other monitors a lower limit, reducing the number of discrete comparator assemblies required. The open-collector outputs support direct interface to an enable, shutdown, or fault input through an external pull-up. The LM2903B-Q1 generation is described as offering lower offset voltage and lower propagation delay than the earlier LM2903 family, which are useful traits in protection systems. Validate threshold accuracy, response time, and output-current limits against the system thresholds.
پیشنهادی
Industrial Sensor Interfacing
The LM2903BQDRQ1 is useful for converting analog sensor conditions into discrete control decisions. A resistive divider can translate a sensor output into the differential input range, and the comparator then generates an open-collector event when the sensing threshold is crossed. Rail-to-rail input operation helps the design use much of the available signal range, while the -40 °C to +125 °C rating supports extended-temperature industrial equipment. Choose the pull-up voltage to match the controller domain and size the resistor for the required rise time. Sensor hysteresis or filtering should be added where electrical noise could cause repeated threshold transitions.
پیشنهادی
Automotive Sensor and Actuator Conditioning
The LM2903BQDRQ1 supports threshold decisions around automotive sensors, switches, and actuator feedback loops. Its dual differential inputs permit comparison against a local reference, and the open-collector output can pull down a control line or drive a subsequent transistor stage. The automotive LM2903B-Q1 positioning, AEC-Q100 identification, and extended temperature range make it appropriate for electronics located near harsh vehicle environments. Ensure the surrounding divider, reference, and protection components also meet their respective automotive requirements. The comparator should sit behind appropriate transient protection when connected to external wiring.
پیشنهادی
Relay and Solenoid Drive Logic
The LM2903BQDRQ1 can create a low-side relay or solenoid control signal by comparing a command voltage with a threshold and using the open-collector output to drive an external transistor. This arrangement prevents the comparator from carrying the full actuator current and lets the pull-up voltage match the control logic. Differential inputs are valuable when the command is referenced to a remote or offset signal node. The LM2903B-Q1 family’s stated improvements in propagation delay and input bias current support responsive threshold decisions. Include transistor base current, flyback protection, and contactor-specific voltage ratings in the complete driver design.
پیشنهادی
Logic Level Translation
The LM2903BQDRQ1 can translate between voltage domains by using its open-collector output with a pull-up to the destination logic voltage. When the input comparator detects the appropriate logic state, it releases the pulled-up line or pulls it down, allowing a higher-voltage or lower-voltage domain to be read by the receiving circuit. This arrangement is particularly useful because the output-high level is set by the external resistor rather than a fixed internal voltage. Keep the pull-up current within the output rating and check the destination receiver’s thresholds. Input and output absolute-maximum limits must also be checked for every translated voltage.
پیشنهادی
خلاصه محصولات پیشنهادی
دادههای مرجع مهندسی برای LM2903BQDRQ1 — مقایسه، راهنمای طراحی و اطلاعات انطباق.
راهنمای انتخاب
مقایسه با جایگزینها
| پارامتر | این محصول | LM2903DR | LM2903BIDR | LM2903BIDRQ1 | LM2903QDRQ1 | LM2903BQDR |
|---|---|---|---|---|---|---|
| Package | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 | SOIC-8 |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels | 2 channels |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Automotive Qualification | AEC-Q100 | Not stated for this ordering code | Not stated for this ordering code | Q1 ordering family | Q1 ordering family | Non-Q1 ordering suffix |
| Family Generation | LM2903B-Q1 with lower offset, supply current, bias current, propagation delay, and improved 2 kV ESD performance | LM2903 family | LM2903B family | LM2903B-Q1 family | LM2903-Q1 family | LM2903B-Q1 family |
تفاوتهای کلیدی
- Automotive LM2903B-Q1 family positioning (در مقابلLM2903QDRQ1)
- Documented drop-in package compatibility (در مقابلLM2903DR)
- Extended-temperature automotive specification (در مقابلLM2903BIDR)
یادداشتهای طراحی
Do not treat the open-collector output as a push-pull logic output. Add a pull-up resistor to the required logic rail and confirm that its maximum current, rise time, and power dissipation are acceptable. If a redesign removes the resistor, the output will remain unable to source current in the high state. Also check whether downstream circuitry requires wired-AND behavior or isolated high-side signaling before reusing this topology.
Place the pull-up resistor close to the LM2903BQDRQ1 output pin to limit the trace length carrying the rising edge. Keep differential input traces short, route them away from switching nodes, and connect the ground return directly to the device ground pin. If the comparator monitors a remote or high-voltage node, place divider and protection components near the connector and provide a defined low-impedance return path to minimize differential pickup.
Add controlled hysteresis around the comparison threshold when slow input transitions or output noise could cause repeated switching. Positive feedback can provide hysteresis, but the resistor network must preserve the available differential input range. Verify offset and propagation delay at the actual temperature and supply voltage, and do not rely solely on nominal values when the decision affects protection, braking, or another safety-relevant function.
Decouple the comparator supply with a local ceramic capacitor and place it adjacent to the supply and ground pins. Keep the supply return current away from sensitive input and output-return paths. When using single-supply operation, confirm that the comparator inputs, outputs, and pull-up rail remain within the datasheet limits under startup, shutdown, and transient conditions; rail-to-rail input wording does not override absolute-maximum ratings.
اطلاعات انطباق
Texas Instruments identifies LM2903B-Q1 as an automotive family and the LM2903BQDRQ1 ordering entry as AEC-Q100. Other compliance declarations are not stated in the cited product information.