LM2903MX - Dual Differential Comparator | Texas Instruments
MPN: LM2903MX ✓ Hoạt độngLM2903MX Tóm tắt
An analog comparator is an integrated circuit that evaluates two input voltages and changes its output state according to their relative polarity. Within the semiconductor hierarchy, a comparator belongs to the broader group of analog ICs and serves as an interface between sensors and digital logic. The LM2903MX is useful when a design needs to detect crossings, thresholds, overvoltage, undervoltage, or differences between two analog signals without converting them into a digital quantity.
The two channels operate independently, allowing one device to implement two unrelated threshold functions. Key features include comparison of input voltages near ground potential, a wide supply range, low current drain, and open-collector outputs that require an external pull-up resistor. Rail-to-rail input behavior is particularly valuable when the signal of interest lies close to either supply rail. The specified 1.3 us response time makes the comparators appropriate for power-line, protection, sensing, and general signal-conditioning circuits.
Typical uses include monitoring a divided battery voltage, detecting an over-temperature condition with a sensor, comparing an adjustable reference with an analog input, and translating a sensor threshold into a logic-level event. The open-collector topology also allows several comparator outputs to share a wired bus when each output has a suitable pull-up and the system design accounts for the resulting behavior.
PCB implementation should follow the manufacturer pin-description table and place input, output, and decoupling connections to minimize switching noise. Input traces should be kept short and away from high-current paths. Use a pull-up resistor sized for the target logic family, and verify its maximum current across all operating conditions. Do not substitute a push-pull output device without reviewing the full pinout and signal behavior.
This page compares the LM2903MX with documented same-footprint alternatives, summarizes verified electrical and package characteristics, and adds practical PCB, logic-interface, and replacement guidance for engineers evaluating this dual comparator.
Bộ thay thế dễ dàng lắp đặt cho LM2903MX — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2903MX (cùng hình factor và footprint) — khác nhau ở Comparator Type, Operating Temperature Range, Package, Supply Current.
LM2903MX/NOPB
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2903MX
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903M
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2903MX Tỷ lệ tối đa & tính chất điện
| Comparator Type | General Purpose |
| Number of Comparators | 2 |
| Supply Voltage Range, Single Supply | 2 V to 36 V |
| Supply Voltage Range, Dual Supply | 1 V to 18 V |
| Response Time | 1.3 us |
| Kiểu đầu ra | Open-Collector |
| Input Common-Mode Capability | Rail-to-Rail |
| Logic Compatibility | CMOS, MOS, TTL |
| Differential Input Voltage Range | ±38 V |
| Hộp | 8-SOIC, 0.154 in (3.90 mm) body width |
| Số lượng chân | 8 pins |
| Khoảng nhiệt độ hoạt động | -40 °C to +85 °C |
| Low Offset | 0.37 mV |
| Low Input Bias Current | 3.5 nA |
| Điện áp cung cấp | 200 uA per comparator |
| ESD Rating | 2 kV HBM |
Hướng dẫn cấu hình chân LM2903MX 8-soic, 0.154 in (3.90 mm) body width
Cấu hình chân cho LM2903MX (8-soic, 0.154 in (3.90 mm) body width gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM2903MX.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM2903MX phù hợp cho 6 Áp dụngs: Battery Voltage Monitoring, Over-Temperature Protection, Power-Supply Fault Detection, Sensor Threshold Conditioning, Zero-Crossing and Signal Detection, Motor and Solenoid Control Interface.
Battery Voltage Monitoring
The LM2903MX fits battery monitoring because each comparator can evaluate a divided pack voltage against an adjustable reference using the device's 2 V to 36 V single-supply range and rail-to-rail inputs. Connect one channel to a resistor-divider output and the other input to a precision reference, then use the 1.3 us response time to detect an undervoltage or overvoltage event. The open-collector output can pull up a logic interrupt, though the divider resistance, reference accuracy, and fault-current limits require separate validation.
Được đề xuất
Over-Temperature Protection
The LM2903MX can implement over-temperature protection by comparing a temperature-sensor signal with a threshold generated by a resistor network or reference. Its rail-to-rail input capability is useful when the sensor output approaches either supply rail, and the 1.3 us response time supports prompt shutdown signaling. Because the output is open-collector, a pull-up can drive a shutdown input or fault indicator. Component tolerances, sensor slope, hysteresis, and the propagation path should be evaluated together.
Được đề xuất
Power-Supply Fault Detection
The LM2903MX is appropriate for detecting an out-of-range power rail by comparing a scaled feedback voltage with a reference. Two independent channels can supervise positive and negative rails or implement upper and lower limits on one supply. The wide 2 V to 36 V operating range supports many industrial and automotive supply systems, while the open-collector output provides a flexible fault bus with an external pull-up. Designers should include input filtering, verify tolerance stack-up, and confirm that all inputs remain within rated conditions during faults.
Được đề xuất
Sensor Threshold Conditioning
The LM2903MX converts a sensor-derived analog threshold into a logic-compatible event by comparing the sensor output with a reference voltage. Rail-to-rail input behavior makes it useful for low-level current, voltage, and resistive sensing where the signal can lie close to ground. Its 1.3 us response time supports reasonably fast threshold recognition, and the open-collector output can be pulled up to the voltage used by CMOS, MOS, or TTL circuitry. Hysteresis may be added with positive feedback to prevent repeated switching near the threshold.
Được đề xuất
Zero-Crossing and Signal Detection
The LM2903MX can detect when an analog waveform crosses a reference by using one input for the signal and the other for the threshold. The rail-to-rail input range supports detection near the supply rails, and the specified 1.3 us response time provides a defined switching interval for control or measurement systems. Open-collector outputs can pull up a digital input without committing to a fixed push-pull logic voltage. Input-source impedance, noise, propagation delay, and input overvoltage should be checked for the selected waveform.
Được đề xuất
Motor and Solenoid Control Interface
The LM2903MX can supervise a motor current-sense or position signal before allowing a driver stage to operate. One channel may detect an upper current threshold while the other monitors a control or position condition, and the open-collector output can assert a shutdown input through an external pull-up. The 1.3 us response time helps identify threshold crossings, but actual protection latency also includes signal filtering and the downstream driver's response. Choose pull-up and driver interfaces that tolerate the application's voltage and fault conditions.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2903MX — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2903MX/NOPB | LM2903MX | LM2903M |
|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | ROHM Semiconductor | onsemi |
| Package | 8-SOIC | 8-SOIC | 8-SOIC | 8-SOIC |
| Number of Pins | 8 pins | 8 pins | 8 pins | 8 pins |
Bảo phân biệt quan trọng
- Two independent channels in one device (vsLM2903MX/NOPB)
- Wide single-supply operating range (vsLM2903MX)
- Rail-to-rail input comparison (vsLM2903M)
- Defined response time (vsLM2903M)
Ghi chú thiết kế
Place the LM2903MX close to the signals being compared and keep input traces short. Reserve the exposed ground-lead connections according to the manufacturer layout guidance, connect the supply bypass capacitor at the device, and keep comparator traces away from switching nodes, motor phases, and high-current return paths. For high-impedance sensors, minimize leakage from board contamination and guard the input node when the layout permits.
Use an external pull-up resistor for each open-collector output and size it for the target CMOS, MOS, or TTL input. Verify both the pull-up high level and the maximum sink current at the lowest valid supply voltage. If multiple outputs share a wired node, confirm that only one output can actively pull the node low at a time and account for leakage from every connected device.
Do not treat the SOIC body width as proof of electrical compatibility. Compare pin functions, input common-mode limits, differential input rating, output sink current, response time, offset voltage, input bias current, operating temperature, and qualification before substituting a part. The LM2903MX supports a differential input voltage of up to ±38 V, but sustained operation near an absolute maximum rating should not be used as a normal operating condition.
A comparator can switch abruptly and create narrow current spikes even when its output changes infrequently. Keep the open-collector pull-up network close to the device or receiver, use a value that limits switching current without producing excessive rise time, and route the output away from sensitive analog inputs. Add hysteresis when noise near the threshold could cause repeated output transitions and associated EMI.
Thông tin tuân thủ
The LM2903 product page and distributor records do not explicitly state the requested environmental or material-compliance classifications. Use the manufacturer product page and current declarations for the exact ordering code before making a compliance claim.
