LM2904QP - Dual 26V 700kHz Op-Amp TSSOP-8 | Texas Instruments
MPN: LM2904QP ✓ Hoạt độngLM2904QP Tóm tắt
A dual operational amplifier is an integrated circuit that packs two independent, internally frequency-compensated op amps onto a single silicon die within one package. Op amps are the foundational building blocks of the analog signal chain, sitting within the broader hierarchy of amplifier ICs, linear ICs, and semiconductors, and they perform amplification, buffering, filtering, comparison, and level shifting in virtually every electronic system.
Key features of the LM2904QP include operation from a single supply or dual supplies, a low supply-current drain of approximately 0.7 mA typ that is largely independent of supply voltage, and a common-mode input voltage range that includes ground, allowing direct sensing of signals near 0 V in single-supply systems. The two channels are closely matched, reducing board space versus discrete single-channel amplifiers.
Technically, the LM2904 family uses internally compensated bipolar technology, which guarantees unity-gain stability without external compensation components. The ground-inclusive input common-mode range and single-supply capability eliminate the need for a negative rail in low-side sensing applications, while the 700 kHz bandwidth covers audio, low-speed control loops, and general industrial signal conditioning. Low input bias and offset currents minimize error in high-impedance source applications.
Typical applications include automotive sensor signal conditioning, low-side current sensing, active filters, transducer amplifiers, and battery-powered industrial instrumentation, where single-supply operation near ground and wide temperature tolerance are essential.
Design consideration: the output cannot swing rail-to-rail, so allow headroom on both rails and verify the output swing specification in the manufacturer datasheet against your signal range, especially at elevated temperature and light load.
This page synthesizes the manufacturer product data, drop-in alternatives, comparison tables, and practical design notes in one place, providing engineering context beyond a raw parametric listing.
Bộ thay thế dễ dàng lắp đặt cho LM2904QP — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM2904QP (cùng hình factor và footprint) — khác nhau ở Package, Amplifier Type, Gain-Bandwidth Product, Operating Temperature Range, Automotive Qualification.
LM2904QPWRQ1
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904BQPWRQ1
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2904BQPWR
✅ Drop-In ⚠️ Thông số chưa được xác minh📋 Tham chiếu thay thế (không có trong danh mục)
LM2904QPWRG4Q1
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM2904YPT
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2904QP Tỷ lệ tối đa & tính chất điện
| Number of Channels | 2 |
| Supply Voltage Range (single supply) | up to 26 V |
| Gain Bandwidth Product | 700 kHz |
| Supply Current (per amplifier) | 0.7 mA (typ) |
| Common-Mode Input Voltage Range | Includes ground |
| Input Type | Bipolar, internally compensated |
| Automotive Qualification | AEC-Q100 qualified (Q package) |
| Khoảng nhiệt độ hoạt động | -40C to +125C |
| Hộp | TSSOP-8 (PW) |
| Kiểu lắp đặt | Surface Mount |
| Trạng thái RoHS | Compliant |
Cấu hình chân LM2904QP
| Chân 1 | OUT1 — Output of amplifier 1 |
| Chân 2 | IN1- — Inverting input of amplifier 1 |
| Chân 3 | IN1+ — Non-inverting input of amplifier 1 |
| Chân 4 | V-/GND — Negative supply or ground (single supply) |
| Chân 5 | IN2+ — Non-inverting input of amplifier 2 |
| Chân 6 | IN2- — Inverting input of amplifier 2 |
| Chân 7 | OUT2 — Output of amplifier 2 |
| Chân 8 | V+ — Positive supply |
Ứng dụng tiêu biểu
LM2904QP phù hợp cho 6 Áp dụngs: Automotive Sensor Signal Conditioning, Low-Side Current Sensing, Active Filters and Signal Chains, Battery-Powered Portable Instrumentation, Industrial Control and PLC I/O, Audio Pre-Amplification in Automotive and Consumer Systems.
Automotive Sensor Signal Conditioning
The LM2904QP is AEC-Q100 qualified for the -40C to +125C automotive temperature range, which makes it a natural fit for conditioning signals from throttle position sensors, coolant temperature sensors, MAP/MASS airflow transducers, and battery voltage dividers. Its 26 V rating covers automotive 12 V load-dump transients with modest series protection, and the common-mode input range extending to ground allows direct amplification of low-side sensor outputs without a negative rail. Each of the two matched channels can serve an independent sensor path, halving component count versus single-channel amplifiers. Place a small RC filter (for example 1 kOhm and 100 nF) at each input to reject automotive EMC transients, and keep closed-loop bandwidth well below the 700 kHz limit to preserve phase margin in the presence of wiring capacitance.
Được đề xuất
Low-Side Current Sensing
Because the LM2904QP's common-mode input voltage range includes ground, it can directly amplify the small voltage across a low-side shunt resistor without lifting the input above the rail. A typical single-supply configuration places a 5 to 20 mOhm shunt in the ground return path, amplifies the drop with a gain of 20 to 100 using two precision resistors, and feeds an ADC on a microcontroller. The 0.7 mA typ per-channel supply current suits battery-powered monitoring nodes, while the 700 kHz bandwidth comfortably handles overcurrent-detection loops. Design caveat: the bipolar input stage draws bias current that develops error across large shunt/source impedances, so keep resistor values moderate, and remember the output cannot reach the true ground rail - bias the output slightly above ground or account for the offset in firmware calibration.
Được đề xuất
Active Filters and Signal Chains
The LM2904QP's internally compensated, unity-gain-stable bipolar architecture lets each channel implement Sallen-Key or multiple-feedback active filters up to a few tens of kilohertz without external compensation. In automotive and industrial control boards it commonly forms anti-aliasing filters ahead of ADC inputs, band-limiting filters for PWM feedback, and conditioning stages for analog setpoints. The 700 kHz gain-bandwidth product supports Q values up to roughly 10 at 10 kHz cutoffs while maintaining gain accuracy; for higher-frequency filters select a wider-bandwidth amplifier. The dual-channel package enables a two-stage cascaded filter in one footprint, and the 26 V rating allows filtering of signals referenced to 12 V and 24 V industrial rails. Use 1% resistors and C0G capacitors to control filter corner tolerance across temperature.
Được đề xuất
Battery-Powered Portable Instrumentation
With approximately 0.7 mA typ supply current per amplifier and single-supply operation from low voltages, the LM2904QP suits battery-operated meters, gas detectors, weigh scales, and handheld test instruments. The ground-inclusive input common-mode range means signals generated near 0 V, such as photodiode or thermocouple outputs referenced to ground, can be amplified directly. The dual configuration provides a signal channel plus a spare for filtering, buffering, or a voltage reference buffer within a single 8-pin TSSOP, saving board area in compact enclosures. For maximum battery life, verify the supply current over the full supply range since the drain is specified as largely independent of supply voltage, and power the device from a regulated rail if input signals approach the upper common-mode limit near V+.
Được đề xuất
Industrial Control and PLC I/O
On 24 V industrial rails the LM2904QP's 26 V rating requires modest headroom, and it is widely used in PLC analog input modules, 4-20 mA receiver loops, and actuator drive conditioning where cost and robustness dominate. The wide -40C to +125C Q-grade temperature range covers sealed control cabinets and motor-drive environments, and each dual package handles one transmit and one receive conditioning path. The 700 kHz bandwidth is more than sufficient for 4-20 mA loop bandwidths of a few hundred hertz and for PWM current-loop feedback filtering below 10 kHz. For industrial use, add input series resistance and clamp diodes for IEC surge exposure, and ensure the output stage load does not pull the swing away from the ADC reference range at the connected controller.
Được đề xuất
Audio Pre-Amplification in Automotive and Consumer Systems
The LM2904QP's 700 kHz bandwidth exceeds the full audio band by more than an order of magnitude, and its dual matched channels are well matched for stereo pre-amplifiers, microphone buffers, and tone-control stages in automotive head units and low-cost consumer audio. The 26 V rating permits operation from vehicle battery rails or 24 V audio supply rails for higher headroom, while the ground-referenced single-supply capability simplifies biasing with a mid-rail virtual ground generated from a resistor divider buffered by one channel. Limit closed-loop gain so that the gain-bandwidth product maintains loop gain at 20 kHz (a gain of 100 consumes 2 MHz of bandwidth, which exceeds the device limit, so keep audio-stage gains below roughly 30). Cross-over distortion inherent to the class-AB output stage at light loads can be mitigated with a small pull-down load to ground.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM2904QP — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM2904QPWRQ1 | LM2904BQPWRQ1 | LM2904BQPWR | LM2904QPWR | LM2904YPT |
|---|---|---|---|---|---|---|
| Package | TSSOP-8 (PW) | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 (PW) - same | TSSOP-8 - same |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics |
| Channels | 2 | 2 | 2 | 2 | 2 | 2 |
| Pinout | Standard dual op amp 8-pin (OUT1/IN1-/IN1+/V-/IN2+/IN2-/OUT2/V+) | Identical | Identical | Identical | Identical | Identical (industry-standard LM2904 pinout) |
Bảo phân biệt quan trọng
- Automotive AEC-Q100 qualification (vsLM2904QPWR)
- Improved precision at no layout cost (vsLM2904BQPWRQ1)
- Dual-channel integration with ground-inclusive inputs (vsTS321IDR)
Ghi chú thiết kế
Supply the LM2904QP from a rail within its 26 V rating and decouple with a 100 nF ceramic capacitor directly across pins 8 and 4, plus a 1 uF bulk capacitor per board region. In automotive 12 V systems, account for load-dump transients by adding a series resistor or TVS diode ahead of the supply pin. The supply current is approximately 0.7 mA typ per amplifier and largely independent of supply voltage, so battery-life budgets can be computed easily; however, verify current over temperature and supply extremes for sleep-mode designs.
Do not assume rail-to-rail operation: the LM2904QP output cannot swing fully to either rail, and the input stage loses precision when the common-mode voltage approaches V+. In single-supply low-side sensing this means the output rests slightly above ground - either bias the ADC range accordingly or add a small pull-down resistor on the output to sink the crossover current and improve low-level accuracy. Also remember that a gain of 30 already consumes about 21 MHz-worth of the 700 kHz gain-bandwidth budget at 20 kHz; keep closed-loop gains modest in audio circuits.
Keep input traces short and guard the inverting node of each high-gain stage to reduce leakage and parasitic capacitance, which degrade phase margin and offset accuracy. Route the ground pin (pin 4) as a low-impedance return, especially when the output drives loads that return through the same ground, since shared return impedance couples output current into the input reference. Place 100 nF decoupling within 2 mm of pin 8. Where the amplifier drives cables or capacitive loads above roughly 100 pF, add an isolation resistor (tens of ohms) in series with the output to prevent oscillation.
Estimated: at 0.7 mA typ per channel from a 26 V supply, worst-case device dissipation is roughly 26 V x 1.4 mA = about 36 mW, far below the TSSOP-8 thermal capability, so self-heating is negligible. The dominant thermal consideration is instead the ambient environment: the Q package is qualified to +125C, so verify adjacent hot components (regulators, drivers) do not create local hotspots above the qualified range on the PCB.
Thông tin tuân thủ
Q-suffix package denotes automotive grade per Texas Instruments family structure (LM2904-Q1 is listed by TI as automotive-grade). RoHS status listed as compliant on distributor listings; REACH and conflict-minerals status not stated in retrieved data.