LM324N/NOPB - Low-Power Quad Op Amp | Texas Instruments
MPN: LM324N/NOPB ✓ Hoạt độngLM324N/NOPB Tóm tắt
An operational amplifier is an analog signal-conditioning device that uses high open-loop gain and negative feedback to amplify voltage differences. The LM324 belongs to the general-purpose amplifier family, combining internal frequency compensation with a common-emitter output stage that can source and sink current. Placing four amplifiers in one 14-pin PDIP saves board area in analog circuits that need several independent signal-processing channels.
Key features include four amplifier circuits per package, internally frequency compensation, operation from a single power supply, and a wide input-voltage range. Each amplifier provides independent input, output, and power connections, allowing different sections of the device to process separate signals. The quad organization makes the LM324N/NOPB suitable for sensor conditioning, buffer stages, analog summation, and general instrumentation.
The internal compensation trades gain bandwidth for ease of use by eliminating the need for an external compensation network in typical closed-loop configurations. Because the amplifiers operate from one supply, the usable signal range depends on the supply voltage and the common-mode input limits. Engineers should check the manufacturer datasheet for input common-mode range, output swing, output-current capability, and stability requirements before fixing the gain and bypassing arrangement.
Typical applications include transducer-amplifier front ends, DC gain blocks, active filters, sensor interfaces, and general instrumentation. In a sensor-conditioning channel, one amplifier can amplify a bridge or resistive-transducer output while another channel provides buffering, reference conversion, or output amplification. The four independent amplifiers also allow parallel use for improved output-current capability or broader signal handling within one package.
When designing around the LM324N/NOPB, maintain adequate bypass capacitance at the supply pins and keep feedback-loop routing compact. Check input-bias-current effects at high source impedances, verify output swing at the intended load, and confirm that the selected gain and load remain compatible with the device’s stability characteristics. The PDIP package also requires adequate spacing from conductive surfaces and nearby heat sources.
This page consolidates the manufacturer description, package information, cross-reference findings, and application guidance for engineers evaluating the LM324N/NOPB. It also organizes same-package alternatives, practical circuit considerations, and side-by-side parameter coverage so that form, fit, function, and signal-chain trade-offs can be evaluated before PCB release.
Bộ thay thế dễ dàng lắp đặt cho LM324N/NOPB — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM324N/NOPB (cùng hình factor và footprint) — khác nhau ở Supply Configuration, Mounting Type, Package, Amplifier Type, Compensation.
LM324AN/NOPB
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324AN
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM324APWR
✅ Drop-In ⚠️ Thông số chưa được xác minhLiên hệ để biết giá
Xem tài liệu →LM324N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324N
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM324N/NOPB Tỷ lệ tối đa & tính chất điện
| Number of Amplifiers | 4 circuits |
| Amplifier Type | Single operational amplifier |
| Cấu trúc | 4 independent, high-gain operational amplifiers |
| Compensation | Internally frequency compensated |
| Supply Configuration | Single power supply |
| Power Class | Low power |
| Package Type | 14-PDIP |
| Total Pin Count | 14 pins |
| Kiểu lắp đặt | Through-hole |
| Primary Application | Transducer amplifiers, DC gain blocks, and conventional op-amp circuits |
Cấu hình chân LM324N/NOPB
| Chân 1 | OUT1 — Amplifier 1 output |
| Chân 2 | -IN1 — Amplifier 1 inverting input |
| Chân 3 | +IN1 — Amplifier 1 non-inverting input |
| Chân 4 | GND — Ground connection |
| Chân 5 | +IN2 — Amplifier 2 non-inverting input |
| Chân 6 | -IN2 — Amplifier 2 inverting input |
| Chân 7 | OUT2 — Amplifier 2 output |
| Chân 8 | OUT3 — Amplifier 3 output |
| Chân 9 | -IN3 — Amplifier 3 inverting input |
| Chân 10 | +IN3 — Amplifier 3 non-inverting input |
| Chân 11 | GND — Ground connection |
| Chân 12 | +IN4 — Amplifier 4 non-inverting input |
| Chân 13 | -IN4 — Amplifier 4 inverting input |
| Chân 14 | OUT4 — Amplifier 4 output |
Ứng dụng tiêu biểu
LM324N/NOPB phù hợp cho 6 Áp dụngs: Resistive Transducer Signal Conditioning, DC Gain and Reference Buffering, Industrial Sensor Interface, Active Audio and Control Filtering, General-Purpose Instrumentation, Power Supply Monitoring and Control Loops.
Resistive Transducer Signal Conditioning
The LM324N/NOPB suits resistive-transducer front ends because it provides four independent high-gain amplifiers with internal frequency compensation and single-supply operation. One channel can amplify a strain-gauge, RTD, or resistive-sensor differential while the remaining channels provide buffering, offset correction, and output amplification. Internal compensation removes the need for an external compensation capacitor in conventional closed-loop use, simplifying the analog chain. The design must still account for input bias-current error at high sensor impedance and the output-swing limits at the selected supply voltage.
Được đề xuất
DC Gain and Reference Buffering
In DC gain-block and reference-buffer circuits, the LM324N/NOPB converts a low-level voltage into a larger, usable analog signal while maintaining a stable output reference. Its four internally compensated amplifiers can form cascaded gain stages, difference amplifiers, or unity-gain buffers without requiring an external compensation network. Because classic LM324-class outputs are not rail-to-rail, leave the necessary headroom to the positive and negative rails. Feedback-component values should also be kept close to the amplifier to minimize parasitic feedback and improve transient behavior.
Được đề xuất
Industrial Sensor Interface
The LM324N/NOPB is applicable to industrial sensor interfaces that combine sensing, scaling, and buffering in one analog subsystem. Its single-supply architecture simplifies grounding, while four independent channels allow simultaneous conditioning of multiple inputs or a combination of sensing, filtering, and output-driver stages. The wide single-supply operating concept supports industrial designs, but the exact supply limits must be checked against the LM324-N datasheet. Input protection, common-mode range, output loading, and isolation from switching nodes require separate engineering review.
Được đề xuất
Active Audio and Control Filtering
The LM324N/NOPB can implement active low-pass, high-pass, and band-pass sections where the required bandwidth does not demand a high-speed amplifier. Internal frequency compensation makes each channel convenient to use as a conventional closed-loop filter stage, while the four-channel package reduces the component count in multistage audio and control filters. Component tolerances determine the filter accuracy, and the non-rail-to-rail output can limit signal swing in low-voltage systems. Confirm stability with the intended source impedance and capacitive load before releasing the layout.
Được đề xuất
General-Purpose Instrumentation
The LM324N/NOPB is well suited to general instrumentation where inexpensive, independent analog channels are needed for amplification, buffering, and level shifting within the common-mode limits. Its internally compensated high-gain architecture supports conventional amplifier configurations without external frequency-compensation components. In test and measurement equipment, bypass capacitors and grounded guard techniques help control noise, while careful feedback routing limits susceptibility to parasitic oscillation. The DIP package makes hand assembly and socket-based prototyping convenient.
Được đề xuất
Power Supply Monitoring and Control Loops
The LM324N/NOPB can supervise a power rail, amplify a feedback-error voltage, and drive a slow control signal in low-bandwidth regulation or monitoring loops. Four amplifiers permit separate sensing, error amplification, filtering, and actuator-driving functions. The device’s low-power general-purpose architecture is useful where switching noise and high bandwidth are not central requirements. Designers must verify that the monitored signal remains inside the input common-mode range and that the output can reach the required control level with the chosen load.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM324N/NOPB — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
Choose the STMicroelectronics LM324N or onsemi LM324N when sourcing a second manufacturer is advantageous, but review input bias current, offset, common-mode range, output drive, bandwidth, and stability against the original circuit. Do not choose a rail-to-rail amplifier merely to obtain the same DIP footprint; use one when the signal must operate closer to the supply rails, lower offset or bias current is essential, or higher bandwidth is required.
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM324AN/NOPB | LM324AN | LM324AP | LM324N | LM324N |
|---|---|---|---|---|---|---|
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | STMicroelectronics | onsemi |
| Package | 14-PDIP | 14-PDIP - same | 14-PDIP - same | 14-PDIP - same | 14-DIP - same | 14-DIP - same |
| Number of Amplifiers | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits | 4 circuits |
| Supply Configuration | Single power supply | Single power supply | Single power supply | Single power supply | Single power supply | Single power supply |
| Compensation | Internal | Internal | Internal | Internal | Internal | Internal |
| Mounting Style | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole PDIP | Through-hole DIP | Through-hole DIP |
Bảo phân biệt quan trọng
- Four independent amplifier channels in one 14-pin PDIP package (vsLM2902KNSR)
- Single-supply general-purpose operation with internal compensation (vsLM324N)
- Exact Texas Instruments ordering configuration (vsLM324N)
Ghi chú thiết kế
Place the supply bypass capacitor immediately adjacent to the LM324N/NOPB supply and ground connections, and keep the current loop compact. Because all four amplifiers share the same supply pins, supply noise can affect every channel. Route sensitive signals away from switching-node copper and high-current return paths. Use separate local decoupling where multiple analog stages are distributed across the board.
Do not assume that the outputs can reach either supply rail. The classic LM324-class output stage requires output headroom, and the inputs also have common-mode restrictions under single-supply operation. Check the output load, gain, and signal level against the LM324-N recommended operating conditions. Using a rail-to-rail amplifier is preferable when the required input or output voltage approaches the supply limits.
Keep feedback resistors and their signal paths close to the relevant amplifier pins, and avoid routing inputs beneath noisy analog or digital traces. High-impedance inputs should use guarded or driven-shield techniques where offset drift from bias current is significant. For the PDIP footprint, maintain adequate clearance from conductive hardware and confirm that the selected socket and board layout accommodate the pin-1 orientation.
Thông tin tuân thủ
The LM324-N is a general-purpose amplifier rather than an automotive-qualified device, so AEC-Q100 is not applicable. RoHS, REACH, lead-free, halogen-free, and conflict-minerals statements should be confirmed from the current TI product documentation or declaration for the exact ordering code.