LM339ADBR - 4-Channel 30V Open-Collector Comparator | Texas Instruments
MPN: LM339ADBR ✓ Hoạt độngLM339ADBR Tóm tắt
A quad differential comparator is an analog integrated circuit that compares two input voltages and changes its output state when their difference crosses a defined threshold. The LM339 belongs to the comparator hierarchy within analog ICs and broader semiconductor signal-conditioning systems. Its four independent channels can compare unrelated signals because the devices share only power and ground connections.
The open-collector outputs support wired-AND operation, level translation, and direct connection to pull-up resistors. Low input offset voltage of 0.37mV supports accurate switching decisions near the comparison threshold, while 3.5nA input bias current reduces source-loading effects in high-impedance sensing circuits. A 2V minimum supply permits operation from low-voltage rails, and the 30V operating range supports higher-voltage industrial systems. The B-version family also supports maximum ratings up to 38V.
Each channel provides independent comparison inputs, allowing one device to implement four threshold, sorting, window-detection, or fault-monitoring functions. The open-collector architecture is useful when several comparator outputs must share a bus, although an external pull-up resistor is required for normal logic-high operation. Quiescent current of 200µA per comparator supports low-power monitoring systems when the device is operated near light-load conditions.
Typical uses include industrial sensor monitoring, battery threshold detection, power-supply sequencing, overvoltage and undervoltage protection, window comparators, and logic interfaces. The low offset and bias-current characteristics are particularly useful when the source impedance and input voltage accuracy are important. The 14-pin SSOP package also supports compact board layouts where a larger SOIC or DIP package would be unnecessary.
For reliable operation, select pull-up resistors according to the required rise time and sink-current budget, keep input and output paths separated to prevent switching transients from affecting comparisons, and observe the absolute maximum supply rating of 38V. The open-collector stage does not actively drive a logic-high state, so every application must include an appropriate pull-up arrangement or relay interface.
This product record combines the electrical characteristics, package details, sourcing information, drop-in family options, and practical circuit guidance needed to evaluate the LM339ADBR in new comparator designs.
Bộ thay thế dễ dàng lắp đặt cho LM339ADBR — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Các biến thể trong loạt này
Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM339ADBR (cùng hình factor và footprint) — khác nhau ở Differential Input Voltage Range, Number of Channels, Output Type, Package, Common-Mode Input Voltage Range.
LM339DBRE4
✅ Drop-InLiên hệ để biết giá
Xem tài liệu →LM2901DBR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM239DBR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM2901ADBR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM239ADBR
✅ Drop-In📋 Tham chiếu thay thế (không có trong danh mục)
LM339ADBR Tỷ lệ tối đa & tính chất điện
| Comparator Type | Quad differential voltage comparator |
| Number of Channels | 4 independent channels |
| Supply Voltage Range | 2V to 30V |
| Maximum Rated Supply Voltage | 38V |
| Kiểu đầu ra | Open-collector |
| Input Offset Voltage | 0.37mV |
| Input Bias Current | 3.5nA |
| Điện áp cung cấp | 200µA per comparator |
| Common-Mode Input Voltage Range | Includes ground |
| Differential Input Voltage Range | Equal to the maximum-rated supply voltage, up to ±38V |
| ESD Rating | 2kV HBM |
| Logic Compatibility | Compatible with TTL, MOS, and CMOS |
| Hộp | 14-pin SSOP |
| Kiểu lắp đặt | Surface mount |
| Trạng thái RoHS | RoHS3 compliant |
| Lead-Free Status | Lead free |
Cấu hình chân LM339ADBR
| Chân 1 | OUT1 — Comparator 1 open-collector output |
| Chân 2 | IN1- — Comparator 1 inverting input |
| Chân 3 | IN1+ — Comparator 1 noninverting input |
| Chân 4 | GND — Ground connection |
| Chân 5 | IN2+ — Comparator 2 noninverting input |
| Chân 6 | IN2- — Comparator 2 inverting input |
| Chân 7 | OUT2 — Comparator 2 open-collector output |
| Chân 8 | OUT3 — Comparator 3 open-collector output |
| Chân 9 | IN3- — Comparator 3 inverting input |
| Chân 10 | IN3+ — Comparator 3 noninverting input |
| Chân 11 | GND — Ground connection |
| Chân 12 | IN4+ — Comparator 4 noninverting input |
| Chân 13 | IN4- — Comparator 4 inverting input |
| Chân 14 | OUT4 — Comparator 4 open-collector output |
Ứng dụng tiêu biểu
LM339ADBR phù hợp cho 6 Áp dụngs: Industrial Sensor Threshold Monitoring, Battery Overvoltage and Undervoltage Protection, Power Supply Sequencing and Rail Monitoring, Window Comparator and Signal Qualification, Automotive and Heavy Equipment Interlock, Digital Logic Interface and Level Translation.
Industrial Sensor Threshold Monitoring
The LM339ADBR fits industrial sensor monitoring because its four independent differential channels can establish separate warning, alarm, or control thresholds. Its 3.5nA input bias current limits the loading imposed on high-impedance sensors, while the A-grade 0.37mV input offset supports decisions close to the reference voltage. The device accepts a single supply from 2V to 30V, allowing it to operate directly from many industrial rails. Each channel compares a sensor signal with a local reference and drives an open-collector output. Pull-up resistors convert the open-collector state into a logic level, and the shared four-channel package reduces component count compared with four separate comparators.
Được đề xuất
Battery Overvoltage and Undervoltage Protection
The LM339ADBR can implement independent upper and lower battery thresholds using two of its four comparison channels. Its 2V-to-30V supply range supports low-voltage battery systems, and the 38V maximum rated supply provides additional transient headroom when protection devices are present. The 0.37mV offset helps reduce the error introduced when a battery voltage is compared against a precision reference. Additional channels can supervise charger status, load presence, or system initialization. Because every output is open-collector, the protection signals can be combined into a wired-AND fault bus or pulled up to the system logic voltage without requiring four dedicated input buffers.
Được đề xuất
Power Supply Sequencing and Rail Monitoring
The LM339ADBR is suitable for monitoring multiple supply rails and sequencing controller enable signals. Its four independent channels can compare each rail against a reference, while the open-collector outputs can provide wired-AND fault signaling or individual active-low control signals. The wide 2V-to-30V operating range covers low-voltage processor rails and higher-voltage industrial systems. Its 200µA per-comparator supply current is useful when continuous monitoring is required across multiple rails. External pull-up resistors should be selected to match the controlled interface voltage and sink-current requirements. Designers should also allow sufficient logic threshold margin so that normal rail tolerance does not cause repeated comparator transitions.
Được đề xuất
Window Comparator and Signal Qualification
The LM339ADBR can implement a signal-quality window detector by using two comparator channels to establish upper and lower limits. Its low 3.5nA input bias current is beneficial when the monitored signal comes from a high-impedance source, and its 0.37mV offset supports precise limit placement. The remaining two channels can monitor auxiliary conditions or provide independent fault flags. Open-collector outputs make it practical to combine both limit states into one fault output or route separate indications to a controller. The design must account for input common-mode limits, output pull-up behavior, and the response characteristics of the compared signals rather than treating the comparator as a general-purpose amplifier.
Được đề xuất
Automotive and Heavy Equipment Interlock
The LM339ADBR can support machine-interlock and fault-detection functions where multiple discrete conditions must be consolidated. Four open-collector channels can monitor switches, sensor lines, and safety-related thresholds, with wired-AND outputs providing a compact common fault indication. The 2V-to-30V supply range accommodates many 12V and 24V systems, and the 38V maximum rated supply supports protected supply rails. The low 3.5nA input bias current reduces disturbance of resistive sensing networks. Automotive qualification is not established for this ordering, so an explicitly qualified comparator should be selected when formal automotive requirements apply. Input protection and transient filtering remain essential in vehicle or industrial environments.
Được đề xuất
Digital Logic Interface and Level Translation
The LM339ADBR can serve as a robust open-collector interface between analog sensing circuits and digital control logic. Each comparator channel can translate a thresholded signal to the target logic domain by using a pull-up resistor connected to the desired logic voltage. The open-collector output supports TTL, MOS, and CMOS compatibility according to the Texas Instruments LM339A documentation. Four channels reduce board area when several digital status signals must be conditioned. The 0.37mV offset supports accurate threshold decisions, although comparator outputs should not be used for high-speed data beyond the device's specified response characteristics. Select pull-up values carefully to balance rise time, power consumption, bus capacitance, and output sink-current capability.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM339ADBR — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này | LM339DBR | LM2901DBR | LM239DBR | LM2901ADBR | LM239ADBR |
|---|---|---|---|---|---|---|
| Package | 14-pin SSOP | 14-pin SSOP | 14-pin SSOP | 14-pin SSOP | 14-pin SSOP | 14-pin SSOP |
| Brand | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments | Texas Instruments |
| Comparator Channels | 4 | 4 | 4 | 4 | 4 | 4 |
| Supply Voltage Range | 2V to 30V | 2V to 30V | 2V to 30V | 2V to 30V | 2V to 30V | 2V to 30V |
| Output Type | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector | Open-collector |
| Device Family and Grade | LM339A grade | LM339 standard grade | LM2901 family | LM239 family | LM2901 A grade | LM239 A grade |
Bảo phân biệt quan trọng
- Improved A-grade input offset (vsLM339DBR)
- Four independent channels in one package (vsLM2901DBR)
- Wide single-supply operating range (vsLM239ADBR)
- Open-collector wired-AND capability (vsLM2901ADBR)
Ghi chú thiết kế
The open-collector outputs require external pull-up resistors. Select each resistor according to the target logic voltage, bus capacitance, required rise time, and maximum sink current. Do not allow an output to remain in a high-impedance state without a defined pull-up path, and ensure that the pull-up voltage remains within the output and device ratings.
Place pull-up resistors close to the relevant comparator outputs to minimize trace capacitance and obtain a predictable rising edge. Keep comparator inputs away from switching nodes and output traces, because the open-collector transitions can produce coupling into adjacent input paths. Connect the ground pins to a low-impedance ground plane and provide local supply bypassing near the device.
The 3.5nA input bias current makes the LM339ADBR suitable for many high-impedance sensing networks, but source resistance still forms an offset with bias current. Estimated: an input source of 10kΩ produces an input-current error of 35µV, while 1MΩ produces 3.5mV. Use the input-bias-current limit and source impedance when calculating comparison-point error.
The quoted 200µA supply current applies to each comparator channel, so four active channels can consume more current than a single-channel estimate suggests. Estimated: at 30V, 200µA per channel corresponds to 6mW per channel and 24mW for four channels before pull-up loading is included. Include pull-up current in the overall power budget.
Thông tin tuân thủ
The catalog record identifies the LM339ADBR as RoHS3 compliant and lead free. Automotive qualification, REACH status, halogen-free status, and conflict-minerals status are not established by the available product information.