LM339LVRTER - Quad 5.5V Comparator | Texas Instruments
MPN: LM339LVRTER ✓ Hoạt độngLM339LVRTER Tóm tắt
A voltage comparator is an analog integrated circuit that compares two input voltages and changes its output state when the non-inverting input rises above the inverting input, or vice versa. Comparators belong to the broader integrated-circuit hierarchy and are used to implement threshold detection, level translation, signal conditioning, overvoltage detection, and autonomous system decisions. The LM339LV belongs to the low-voltage comparator family and is intended to replace standard LM339-family devices in low-voltage systems where rail-to-rail input operation improves usable signal range.
Four independent channels allow one device to implement several comparison functions without using separate single-channel packages. The 1.65 V to 5.5 V supply range supports low-voltage portable, embedded, industrial-control, and mixed-signal systems. Rail-to-rail input behavior permits sensing signals near either supply rail, while the open-collector outputs provide flexible interface options when paired with suitable pull-up resistors. Maximum quiescent current is 35 µA per channel.
The open-collector architecture requires an external pull-up resistor on each output node. This arrangement allows wired-open logic, level translation to another supply voltage, and direct interfacing with open-drain-compatible devices. Because the output transistor can sink current but cannot actively drive a supply rail, output rise time depends on the pull-up resistance, total bus capacitance, and leakage from connected devices. System designers should not substitute a push-pull output without rechecking downstream logic compatibility.
Typical uses include battery-powered threshold detection, sensor signal conditioning, overvoltage and undervoltage monitoring, industrial control logic, and four-channel level translation. The quad organization is especially useful when a system compares several rails or sensor thresholds against independent references. Input offset, common-mode behavior, response delay, and output leakage should be considered when setting switching thresholds or designing hysteresis.
For reliable operation, place the pull-up resistor close to the output node and route comparator inputs away from switching-node and high-current paths. The small WQFN package benefits from careful assembly practices and adequate PCB copper, although exposed-pad thermal requirements depend on ambient temperature and dissipation. Confirm the manufacturer pin description table before assigning signals because the public result excerpts do not reproduce every terminal name.
This product page consolidates the key electrical ratings, package information, application guidance, and replacement considerations for LM339LVRTER. It also distinguishes true drop-in options from comparators that differ in channel count, package, output architecture, or supply rating, helping engineers make a board-level decision without assuming that every similarly named LM339 device is interchangeable.
Bộ thay thế dễ dàng lắp đặt cho LM339LVRTER — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.
Không có bộ thay thế dễ dàng lắp đặt sẵn có cho sản phẩm này.
Yêu cầu các bộ thay thếLM339LVRTER Tỷ lệ tối đa & tính chất điện
| Comparator Type | General-purpose voltage comparator |
| Number of Channels | 4 channels |
| Supply Voltage Range | 1.65 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Kiểu đầu ra | Open-collector |
| Propagation Delay | 600 ns typical |
| Device-Level Propagation Delay | 1 µs |
| Điện áp yên tĩnh | 35 µA maximum per channel |
| Khoảng nhiệt độ hoạt động | -40 °C to 125 °C |
| Hộp | 16-WQFN (3 x 3 mm, RTE) |
| Số lượng chân | 16 pins |
| Kiểu lắp đặt | Surface mount |
| ESD Protection | Integrated ESD protection |
Hướng dẫn cấu hình chân LM339LVRTER 16-wqfn (3 x 3 mm, rte)
Cấu hình chân cho LM339LVRTER (16-wqfn (3 x 3 mm, rte) gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.
Không có dữ liệu chân cụ thể sẵn có cho LM339LVRTER.
Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.
Ứng dụng tiêu biểu
LM339LVRTER phù hợp cho 6 Áp dụngs: Battery-Powered Threshold Detection, Industrial Sensor Signal Conditioning, Power-Rail Supervision, Open-Drain Level Translation, Portable Medical and Wearable Electronics, Automotive and Transportation Control.
Battery-Powered Threshold Detection
The LM339LVRTER fits battery-powered sensing because its four channels operate from 1.65 V to 5.5 V and consume no more than 35 µA quiescent current per channel. A resistor divider can establish a reference for each inverting input, while the other input receives a battery, sensor, or divider-derived voltage. Rail-to-rail input operation is valuable when the monitored signal approaches either supply rail. Because the outputs are open-collector, each node requires a pull-up resistor selected to balance low current consumption against the required logic rise time. Four threshold detectors can therefore be implemented with one compact IC, reducing component count while preserving independent reference points and switching behavior.
Được đề xuất
Industrial Sensor Signal Conditioning
The LM339LVRTER can convert slowly changing sensor signals into decisive digital transitions for an industrial controller. Its rail-to-rail inputs allow a divided sensor signal to be compared with a local threshold over most of the 1.65 V to 5.5 V supply range, while the 600 ns typical propagation delay is suitable for many measurement and interlock functions. The open-collector output can feed a controller input through a suitable pull-up or support a wired-open alarm network. Engineers should add hysteresis around the threshold to prevent chatter from sensor noise and should route sensitive input traces away from motors, relays, and switching power stages.
Được đề xuất
Power-Rail Supervision
Four independent LM339LVRTER channels can supervise multiple low-voltage rails against resistor-derived reference points. The device compares divided rail voltages with references and reports faults through open-collector outputs, allowing pull-ups to the monitored logic level. Its 1.65 V to 5.5 V operating range covers common portable and embedded supply domains, and the -40 °C to 125 °C rating supports industrial equipment. The design must account for input offset and resistor tolerances when defining trip points. Use separate pull-up supplies when the monitored outputs connect to a domain different from the comparator supply, and verify that every output remains within its external logic-level limits during startup.
Được đề xuất
Open-Drain Level Translation
The LM339LVRTER open-collector outputs allow a low-voltage domain to drive a higher-voltage logic domain by placing the pull-up resistor on the higher rail. The comparator supply can remain at 1.65 V to 5.5 V while each output transistor sinks current from the external pull-up node. This arrangement is useful for translating fault, ready, or threshold signals between systems with different voltage levels. It is not a high-speed bidirectional translator, so rise time must be checked against bus capacitance and leakage. Pull-up resistance should also be chosen so that the maximum sink-current capability of the output is not exceeded under the worst-case logic-low voltage.
Được đề xuất
Portable Medical and Wearable Electronics
The LM339LVRTER can support low-voltage monitoring in portable medical, wearable, and personal-health devices where four compact sensing channels are useful. The 1.65 V to 5.5 V supply range accommodates small battery systems, while the rail-to-rail inputs improve threshold coverage near the rail limits. Four comparisons can evaluate battery status, sensor thresholds, charge-state signals, or safety-related limits. Because this is a general-purpose comparator rather than a medical-qualified device, system designers must evaluate the complete signal chain for the intended risk classification. Low quiescent current helps conserve battery capacity, while open-collector outputs allow pull-ups to a local low-voltage rail or an appropriate interface domain.
Được đề xuất
Automotive and Transportation Control
The LM339LVRTER can evaluate multiple low-voltage signals in transportation electronics where its -40 °C to 125 °C operating range is useful. Four channels can monitor redundant sensor lines, discrete control signals, or supply-derived thresholds. Rail-to-rail inputs support low-voltage signal chains, and open-collector outputs suit wired-open interfaces used in vehicle electrical systems. The exact LM339LVRTER ordering option is not identified as an AEC-Q100-qualified variant, so it should not be treated as automotive-grade merely because of its temperature range. Vehicle-system qualification, transient protection, fault tolerance, and electromagnetic compatibility must be assessed at the application level.
Được đề xuất
Tóm tắt các sản phẩm được đề xuất
Dữ liệu tham khảo kỹ thuật cho LM339LVRTER — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.
Hướng dẫn chọn lựa
So sánh với các sản phẩm thay thế
| Tham số | Sản phẩm này |
|---|---|
| Brand | Texas Instruments |
| Package | 16-WQFN (3 x 3 mm, RTE) |
| Number of Channels | 4 channels |
| Supply Voltage Range | 1.65 V to 5.5 V |
| Maximum Supply Voltage | 5.5 V |
| Input Common-Mode Range | Rail-to-rail |
| Output Type | Open-collector |
| Propagation Delay | 600 ns typical |
| Quiescent Current | 35 µA maximum per channel |
| Operating Temperature Range | -40 °C to 125 °C |
Bảo phân biệt quan trọng
- Four independent channels in a compact low-voltage package (vsLM393LV)
- Low-voltage operation with rail-to-rail inputs (vsStandard LM339 family devices)
- Flexible open-collector output interface (vsPush-pull comparator families)
Ghi chú thiết kế
Treat the LM339LVRTER as a mixed-signal component even though its function is simple. Keep the four comparator input nets short and position their reference dividers close to the associated inputs. Route inputs away from switching nodes, relay contacts, inductors, and high-current return paths. A solid ground plane reduces sensitivity to common-mode disturbance, while avoiding input traces directly beneath the switching stage can prevent induced threshold errors.
Do not assume an open-collector output can source current. Every output requires a pull-up resistor, and its high level equals the pull-up supply rather than the comparator supply. Confirm the external pull-up voltage remains within the limits of every connected device. Also account for input offset and resistor tolerances when defining trip points; add positive feedback for hysteresis when the compared signal may cross the threshold slowly or contain noise.
Place output pull-up resistors close to the LM339LVRTER pins to minimize the duration of the high-impedance output state and reduce susceptibility to capacitive coupling and leakage. Select resistance from the required rise time, total node capacitance, and available sink-current budget rather than choosing solely for low power. The manufacturer package drawing should be followed for the exposed-pad connection and land pattern, and assembly should maintain the specified solder and moisture-handling controls.
Rail-to-rail input capability does not eliminate EMI sensitivity. If a comparator detects a fast sensor or switching signal, keep the input path compact and consider a small series resistor with input filtering at the pin. Hysteresis must remain larger than the filtered input noise while still meeting the required trip-point accuracy. Validate the complete circuit with conducted and radiated emissions measurements when it operates beside switching power converters or motor drivers.
Thông tin tuân thủ
The current product excerpts do not state the compliance status of the exact LM339LVRTER ordering option. RoHS, REACH, AEC-Q100, lead-free, halogen-free, and conflict-minerals status must be confirmed from the manufacturer product page or declaration before qualification.