Texas Instruments

LM358ADGKRG4 - Dual 700 kHz Operational Amplifier | Texas Instruments

MPN: LM358ADGKRG4 ✗ Cuối đời
2 mV Vdss 200 nA Id 8-VSSOP / 8-TSSOP / 8-MSOP Package
MOQ: 1 |

LM358ADGKRG4 Tóm tắt

Texas Instruments LM358ADGKRG4 is a dual, general-purpose operational amplifier with two independently usable amplifier channels, 700 kHz gain-bandwidth, 0.3 V/µs slew rate, and 2 mV input offset voltage. The device is supplied in an 8-pin VSSOP surface-mount package and is intended for general-purpose signal conditioning, buffering, amplification, and feedback applications. It supports a single-supply operating range up to 26 V and is also suitable for split-supply circuits.

An operational amplifier, or op amp, is a high-gain differential amplifier that uses negative feedback to control gain and improve linearity. The LM358 integrates two independent, internally compensated amplifier sections into one package. Within the semiconductor hierarchy, it belongs to the amplifier IC family, which is part of the broader analog and mixed-signal IC category. Its dual-channel construction can reduce board area when a design needs two amplifier functions.

Key characteristics include a 0.7 MHz gain-bandwidth value, 0.3 V/µs slew rate, and typical supply-current drain of 0.7 mA. The low 200 nA input-bias current supports higher-source-impedance sensing circuits, while the 2 mV input offset specification defines the typical baseline for dc input imbalance. These characteristics make the device suitable for general instrumentation, industrial control, sensor interfaces, and low-to-moderate-frequency analog signal paths.

The LM358 architecture is based on bipolar transistor input stages with complementary output stages. Internally compensated operation simplifies closed-loop designs because no external compensation capacitor is required for typical voltage-follower and non-inverting amplifier configurations. The amplifier can operate from a single positive supply or from positive and negative supplies, allowing common-ground signal-conditioning arrangements to share the same device.

Typical applications include transimpedance-style sensor front ends, audio preamplifier stages, active filters, comparators with suitable output interfacing, power-supply feedback networks, and industrial control interfaces. Its 0.3 V/µs slew rate is sufficient for general analog signals, while the 700 kHz bandwidth is better suited to audio, measurement, and control loops than to high-speed data acquisition.

Designers should provide input and output bypassing close to the device, maintain adequate input and output voltage headroom, and verify common-mode range, output swing, and stability with the intended feedback network. Because the LM358 is not rail-to-rail at both input and output, supply selection must account for the signal range. The 8-pin VSSOP package also requires careful escape routing and thermal assessment in dense layouts.

This page combines the LM358ADGKRG4 electrical characteristics, drop-in replacement assessment, comparison table, application guidance, and practical PCB design notes into a compact engineering reference for component selection and implementation.

Bộ thay thế dễ dàng lắp đặt cho LM358ADGKRG4 — cùng gói, chân-to-chân tương thích. Các bộ phận yêu cầu hàn PCB bị loại trừ.

Các biến thể trong loạt này

Các mẫu cùng loạt có thể lắp đặt dễ dàng tương thích với LM358ADGKRG4 (cùng hình factor và footprint) — khác nhau ở Amplifier Type, Input Offset Voltage, Maximum Supply Voltage.

Texas Instruments
Amplifier Type: Dual general-purpose operational amplifier
Input Offset Voltage: 3 mV
Maximum Supply Voltage: 30 V
So sánh với LM358ADGKRG4 →

LM358ADGKR

✅ Drop-In
Texas Instruments
📦 8-VSSOP (DGK, 3.0 mm width)
Dual general-purpose operational amplifier · 2 channels · 30 V · 700 kHz · 3 mV · 0 °C to +70 °C · VSSOP (DGK) · 8 pins

Liên hệ để biết giá

Xem tài liệu →

LM358ADGKRG4 Tỷ lệ tối đa & tính chất điện

Number of Amplifier Circuits 2 circuits
Amplifier Type General purpose
Gain-Bandwidth Product 700 kHz
Rated Gain-Bandwidth Product 0.7 MHz
Slew Rate 0.3 V/µs
Input Offset Voltage 2 mV
Input Bias Current 200 nA
Typical Supply-Current Drain 0.7 mA
Minimum Single-Supply Operating Voltage 3 V
Maximum Single-Supply Operating Voltage 26 V
Maximum Supply Voltage 16 V
Hộp 8-VSSOP / 8-TSSOP / 8-MSOP
Package Width 3.00 mm
Package Body Width 0.118 inch
Packaging Tape and reel
Kiểu lắp đặt Surface mount

Hướng dẫn cấu hình chân LM358ADGKRG4 0.118 inch

Cấu hình chân cho LM358ADGKRG4 (0.118 inch gói). Thành phần số hiệu này có chân đầu vào, đầu ra và nguồn cung cấp. Tham khảo tài liệu thông số kỹ thuật của nhà sản xuất để biết cấu hình chân bù, bù trừ và chân kích hoạt. Hoàn hảo cho điều kiện tín hiệu và mạch khuếch đại.

Bảng cấu hình chân 0.118 inch cho LM358ADGKRG4

Không có dữ liệu chân cụ thể sẵn có cho LM358ADGKRG4.

Tham khảo: tài liệu kỹ thuật cho cấu hình chân đầy đủ.

Ứng dụng tiêu biểu

LM358ADGKRG4 phù hợp cho 6 Áp dụngs: Industrial Sensor Signal Conditioning, Audio Preamplification and Buffering, Power-Supply Feedback and Control, Active Filtering and Feedback Networks, Battery-Powered Monitoring System, Communication Interface Buffering.

🏭

Industrial Sensor Signal Conditioning

LM358ADGKRG4 fits two-stage industrial sensor conditioning when the signal bandwidth remains below its 700 kHz gain-bandwidth product. The 200 nA input bias current reduces loading on high-impedance sensors, while the 3 V to 26 V single-supply range accommodates common industrial rails. Two channels can provide sequential gain stages or a differential-to-single-ended input stage. Designers should verify the input common-mode range against the sensor output and use the 0.3 V/µs slew rate to assess large-signal settling time.

🎧

Audio Preamplification and Buffering

The LM358ADGKRG4 can provide two general-purpose stages in audio preamplifier or buffer circuits. Its 700 kHz gain-bandwidth product covers the audio band with substantial margin, and the 0.3 V/µs slew rate supports ordinary low-to-moderate level signals. One channel may amplify a microphone or line input while the other drives a subsequent stage or forms an active filter. Headroom calculations should include the input common-mode requirement and the output swing relative to the selected supply voltage.

⚡

Power-Supply Feedback and Control

LM358ADGKRG4 is appropriate for error-amplifier and supervisory feedback functions around 3 V to 26 V single-supply systems. Its 0.7 mA typical supply-current drain suits low-power monitoring circuits, while two channels permit a voltage-feedback amplifier plus a current or threshold-monitoring amplifier. Compensation and loop stability must be evaluated with the power-stage transfer function, output capacitance, and compensation network, particularly when the monitored rail has wide dynamic range or a delayed response.

🔧

Active Filtering and Feedback Networks

The two internally compensated channels in LM358ADGKRG4 can implement active filters, integrators, and feedback networks in instrumentation. A 700 kHz gain-bandwidth product permits useful closed-loop bandwidth for low-frequency measurement and control functions, while 2 mV input offset and 200 nA bias current should be included in dc-error analysis. Keep resistor values high enough to limit thermal noise yet low enough to prevent parasitic loading, and confirm stability with the complete source and load configuration.

📱

Battery-Powered Monitoring System

LM358ADGKRG4 can supervise a battery-derived analog system because it starts at a 3 V supply and has a 0.7 mA typical supply-current drain. One channel may buffer a battery or sensor measurement while the other compares a scaled voltage against a reference. Since the amplifier is not rail-to-rail, the sensing and output ranges must remain inside the usable common-mode and swing regions. Low-current operation should be evaluated with the actual divider impedances and the device's quiescent-current tolerance.

🌐

Communication Interface Buffering

LM358ADGKRG4 can buffer or amplify slow communication-interface signals when rise times remain compatible with its 0.3 V/µs slew rate. The dual-channel arrangement may handle a receive path and a transmit-control path, although modern high-speed interfaces require substantially wider bandwidth. The 200 nA bias current can reduce errors at high source impedances, while the 2 mV offset specification must be compared with the signal resolution. Use short feedback traces and separate sensitive-signal routing from switching nodes.

What is the operating voltage of LM358ADGKRG4?
The LM358ADGKRG4 supports a single-supply operating range from 3 V up to 26 V. It can also operate with positive and negative supply rails for applications requiring a zero-volt signal reference. Texas Instruments lists the LM358 family as an industry-standard dual operational amplifier; use its pin-description and electrical-characteristics tables when confirming output swing and common-mode limits for the selected supply voltage.
What are the key specifications of LM358ADGKRG4 that engineers should know?
The LM358ADGKRG4 combines two general-purpose amplifier channels in an 8-pin VSSOP package. Its principal ratings include 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, 2 mV input offset voltage, 200 nA input bias current, and 0.7 mA typical supply-current drain. These values position it for general instrumentation, buffering, feedback, and audio-frequency analog circuits rather than high-speed or precision rail-to-rail applications.
Where can I download the LM358ADGKRG4 datasheet PDF?
The LM358ADGKRG4 datasheet is available through the Texas Instruments product documentation and the indexed datasheet links on this page. The manufacturer document is titled “Industry-Standard Dual Operational Amplifiers” and contains the electrical characteristics, package information, pin descriptions, typical performance curves, and application guidance needed to evaluate the device. Compare the package drawing for the DGK ordering code before committing a PCB footprint.
Where can I find the LM358ADGKRG4 pinout?
Use the pin-description table in the Texas Instruments LM358ADGKRG4 datasheet to identify each of the eight VSSOP terminals. The device contains two amplifier channels, including their respective non-inverting and inverting inputs, outputs, power terminals, and ground connection. Because the package drawing and pin numbering are critical for PCB construction, do not infer the arrangement solely from the amplifier channel count.
How does LM358ADGKRG4 compare with LM2904?
The LM358ADGKRG4 and LM2904 are closely related dual operational-amplifier families, but their qualification levels and operating-temperature grades differ. LM358-family devices are intended for the broader commercial and industrial temperature range, whereas LM2904-family devices emphasize extended temperature use. A substitution is valid only when the alternative uses the same package and pin arrangement and satisfies the required supply, temperature, offset, and bias-current limits.
What is the best drop-in replacement for LM358ADGKRG4?
The best drop-in replacement must use the same 8-pin VSSOP footprint, preserve the LM358 pinout, and meet the required supply-voltage and temperature limits. Confirm the offset voltage, bias current, common-mode range, output swing, and stability in the proposed circuit before production release. The cross-reference material identifies LM2904 and several compatible or analogous LM358 families, but it does not establish a verified VSSOP substitute for this exact ordering code.
Can a different manufacturer's LM358 equivalent replace LM358ADGKRG4?
A cross-manufacturer LM358 equivalent can replace LM358ADGKRG4 only if it is available in the same 8-pin VSSOP package with a verified pin-to-pin layout. General-purpose LM358 families commonly share functional behavior, but package options, temperature grades, offset limits, and electrical limits vary by manufacturer. Request the candidate's current datasheet and compare those parameters before approving the substitution.
When should I choose LM358ADGKRG4 over another dual op amp?
Choose LM358ADGKRG4 when a design needs two general-purpose amplifier channels, a 0.3 V/µs slew rate, low 200 nA bias current, and operation from a 3 V to 26 V single supply. It is particularly suitable for buffered sensors, audio-frequency signal conditioning, and industrial feedback networks. Select a rail-to-rail amplifier instead when signals approach the supply rails or when a bipolar-compatible input/output range is not required.
Is LM358ADGKRG4 suitable for sensor and industrial signal conditioning?
Yes, LM358ADGKRG4 is suitable for many sensor and industrial signal-conditioning stages because it offers 200 nA input bias current and 700 kHz gain-bandwidth product. Its 0.3 V/µs slew rate supports signals within the audio and general-control bandwidth range. Ensure that the sensor output, common-mode input range, supply rails, and required closed-loop gain remain inside the device's operating limits.
Where to buy LM358ADGKRG4 online?
Use the Request a Quote form on this page to ask about LM358ADGKRG4 availability, order quantity, and current lead time. The listing identifies the part as a Texas Instruments 8-VSSOP dual operational amplifier supplied in tape-and-reel packaging. A purchasing request should include the complete ordering code, target quantity, shipment destination, and required delivery date.
What is the price of LM358ADGKRG4?
Current commercial pricing for LM358ADGKRG4 should be requested through the Request a Quote form on this page. The form captures the exact MPN, quantity, and delivery requirements so the current channel can be checked without publishing a stale transaction value. The part number's 8-VSSOP tape-and-reel configuration should remain unchanged when obtaining the quotation.
What is the lead time for LM358ADGKRG4?
Request the current lead time through the Request a Quote form on this page. Lead time can depend on the requested quantity, manufacturing condition, packaging configuration, and destination, so a generic schedule may not match the actual order. Include the complete MPN LM358ADGKRG4 and the required shipment date when requesting a commitment.
Is LM358ADGKRG4 in stock?
Check current availability through the Request a Quote form on this page. The searchable listings include LM358ADGKRG4 inventory references, but stock changes by channel and quantity. The quote request is the appropriate method for confirming allocation and delivery for the exact 8-VSSOP tape-and-reel configuration.
What can replace LM358ADGKRG4?
LM358ADGKRG4 can be replaced by a dual operational amplifier with the same 8-VSSOP footprint and pinout, provided its electrical ratings cover the design. LM2904 and other LM358-family devices are logical candidates to investigate, while cross-manufacturer RC4558-class parts may also be considered. Final selection requires package, temperature-grade, offset, bias-current, supply-range, and output-swing comparisons.
Is LM358ADGKRG4 the same as LM358N?
No, LM358ADGKRG4 and LM358N are not package-identical parts. LM358ADGKRG4 uses the compact 8-VSSOP surface-mount package, while LM358N is associated with an 8-pin through-hole package. Both belong to the LM358 family, but changing from one to the other requires a PCB footprint and assembly-process change rather than a direct drop-in substitution.
What design considerations matter for LM358ADGKRG4 decoupling and stability?
Place the supply-bypass capacitor close to the LM358ADGKRG4 power and ground pins, and keep the feedback-resistor network compact to minimize parasitic coupling. The LM358 is internally compensated for common closed-loop configurations, but high-gain layouts can still require careful grounding and output-load checks. Confirm stability with the actual source impedance, capacitive load, supply network, and PCB geometry used in production.

Dữ liệu tham khảo kỹ thuật cho LM358ADGKRG4 — so sánh, hướng dẫn thiết kế và thông tin tuân thủ.

Hướng dẫn chọn lựa

Choose LM358ADGKRG4 for a compact, general-purpose dual-amplifier design that operates from a 3 V to 26 V single supply and does not require rail-to-rail input or output behavior. Its 700 kHz gain-bandwidth product, 0.3 V/µs slew rate, and 200 nA typical input bias current are well suited to audio-frequency buffering, industrial sensor conditioning, active filtering, and power-supply feedback. LM358N is useful for through-hole construction but requires a different PCB footprint. LM2904 is relevant when its extended-temperature qualification is appropriate, though both the package and grade must be verified. Cross-manufacturer LM358-class parts should be selected only when their documentation confirms the same 8-VSSOP footprint and pinout together with acceptable offset, bias-current, common-mode, swing, and temperature limits.

So sánh với các sản phẩm thay thế

Tham số Sản phẩm này
Package 8-VSSOP / 8-TSSOP / 8-MSOP
Brand Texas Instruments
Number of Circuits 2 circuits
Amplifier Type General purpose
Gain-Bandwidth Product 700 kHz
Slew Rate 0.3 V/µs
Input Offset Voltage 2 mV
Input Bias Current 200 nA
Typical Supply-Current Drain 0.7 mA
Minimum Single-Supply Operating Voltage 3 V
Maximum Single-Supply Operating Voltage 26 V
Packaging Tape and reel

Bảo phân biệt quan trọng

  • Two general-purpose amplifier channels in one compact package (vsLM358N)
  • Low input bias current for general-purpose signal conditioning (vsLM2904)
  • Single-supply operating range covers common industrial rails (vsRC4558)

Ghi chú thiết kế

Place the supply-bypass capacitor immediately between the LM358 power and ground pins, with the shortest possible ground return. Keep the amplifier input, feedback components, and output routing away from switching nodes and high-current traces. Because the device uses a compact 8-VSSOP footprint, verify courtyard clearance, solder-paste volume, reflow profile, and assembly inspection requirements before releasing the PCB.

Use the pin-description table and package drawing from the manufacturer datasheet before assigning PCB pads. The LM358 contains two amplifier channels, but the channel order and power-pin locations must not be inferred from generic LM358 diagrams. A board-level drop-in decision also requires matching the exact 8-VSSOP land pattern; a functional LM358 in a through-hole or different surface-mount package cannot be soldered onto the same footprint.

Do not treat the 26 V single-supply capability as permission to apply 26 V to every pin or expect rail-to-rail behavior. Check input common-mode voltage, output swing, supply sequencing, and maximum total supply voltage in the worst-case operating condition. Also confirm the intended gain and capacitive load against the 0.3 V/µs slew rate and 700 kHz gain-bandwidth product rather than relying on the nominal amplifier description alone.

Estimated: the quiescent-current contribution is 0.7 mA per LM358ADGKRG4 package at the typical condition stated in the product listing. Input 3.3 V and calculate supply power as 3.3 V multiplied by 0.7 mA, which equals approximately 2.31 mW for the quiescent path. Add load current and external-network consumption when sizing the regulator and bypass capacitor. This estimate does not include temperature, supply tolerance, or worst-case current variation.

Thông tin tuân thủ

RoHS
Unknown
REACH
Unknown
AEC-Q100
Not Applicable
Không chì
Unknown
Không halogen
Unknown
Khoáng vật xung đột
Unknown

No specific RoHS, REACH, lead-free, halogen-free, or conflict-minerals declaration was identified for the exact ordering code. AEC-Q100 is not applicable to this general-purpose dual operational amplifier.

Dữ liệu được xác minh vào: 2026-11-09 — dữ liệu được xác minh và quản lý bởi đội ngũ kỹ thuật phần cứng của XAIPART

Tìm kiếm liên quan

LM358ADGKRG4 datasheet LM358ADGKRG4 pinout LM358ADGKRG4 datasheet pdf LM358ADGKRG4 equivalent LM358ADGKRG4 replacement LM358ADGKRG4 cross reference LM358ADGKRG4 vs LM2904 LM358ADGKRG4 footprint LM358ADGKRG4 spice model LM358ADGKRG4 price LM358ADGKRG4 stock Texas Instruments LM358ADGKRG4 LM358 VSSOP-8 pinout LM358 dual operational amplifier application LM358ADGKRG4 schematic

Các bộ phận và thuật ngữ liên quan

Texas Instruments LM358ADGKRG4 LM358 LM2904 LM358N RC4558 dual operational amplifier operational amplifier op amp analog integrated circuit amplifier IC semiconductor bipolar operational amplifier gain-bandwidth product slew rate input offset voltage input bias current common-mode input voltage range supply-current drain single-supply operation split-supply operation 8-VSSOP TSSOP MSOP surface-mount technology SMD industrial sensor conditioning audio preamplification active filtering power-supply feedback
Báo giá nhanh RFQ
Hãy điền đầy đủ thông tin — đội ngũ bán hàng của chúng tôi sẽ phản hồi trong vòng 24 giờ
Mã sản phẩm Nhà sản xuất Kiểu đóng gói QTY Giá mục tiêu Phụ
✓
Báo giá đã gửi!

Chúng tôi sẽ trả lời email của bạn trong vòng 24 giờ

1
RFQ đã gửi
2
Phiếu báo giá nhận được
3
Đặt hàng thành công
4
Thanh toán
5
Đã gửi
6
Đã giao hàng
Xem chi tiết RFQ